Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.
| Factory pin | Factory function | Adaptronic function | Manufacturer notes |
|---|---|---|---|
| 4Z | Grn / Red Injector (Rear Secondary) | Injector Output 4 | — |
| 4Y | Grn / Blk Injector (Rear Primary) | Injector Output 3 | — |
| 4X | Grn / Wht Injector (Front Secondary) | Injector Output 2 | — |
| 4W | Grn / Red Injector (Front Primary) | Injector Output 1 | — |
| 4V | Blk / Red Oil Metering Pump 1 bar | Aux Output 7 bar | Always functions opposite to 4T |
| 4U | Blk / Grn Oil Metering Pump 2 bar | Aux Output 8 bar | Always functions opposite to 4S |
| 4T | Blk / Blu Oil Metering Pump | Aux Output 7 | — |
| 4S | Blk / Ora Oil Metering Pump 2 | Aux Output 8 | — |
| 4R | Blu / Wht Boost Control | Aux Output 3 | — |
| 4Q | Blu / Grn Idle Control Solenoid Valve | Aux Output 2 | — |
| 4P | Wht / Blu Defogger input | — | — |
| 4O | Yel / Blk Blower input | Digital Input 7 | Electrical load input |
| 4N | Grn / Red unknown function | — | — |
| 4M | Blu / Ora PRC Solenoid Valve | — | — |
| 4L | Wht / Grn Headlight input | Digital Input 8 | Electrical load input |
| 4K | Brn Fuel pump (circuit opening) relay | Aux Output 5 | — |
| 4J | AWS Solenoid Valve | — | — |
| 4I | Split Air Solenoid Valve | — | — |
| 4H | Red Crankshaft Sensor -ve | SGND | Connects to “white” and “white/black” on the sensor itself (red and green in the loom) |
| 4G | Wht Crank Pos Sensor G (2 tooth) | CAS 2 input | Connects to “green” on the sensor itself (white in the loom) |
| 4F | NC | — | — |
| 4E | Blu Crank Pos Sensor NE (24 tooth) | CAS 1 input | Connects to “red” on the sensor itself (blue in the loom) |
| 4D | Brn / Blk Sensor Ground | SGND | — |
| 4C | Blk Chassis Ground | PGND | — |
| 4B | Blk / Wht Chassis Ground | PGND | — |
| 4A | Blk / Wht Chassis Ground | PGND | — |
| 3P | Blu / Ryel - Relief Solenoid Valve | Aux Output 4 | — |
| 3O | Blu / Red Switch Solenoid Valve | Aux Output 1 | — |
| 3N | Blu Port Air Solenoid Valve | — | If converting to 4 wheel speed inputs, this should be the front right wheel speed input. |
| 3M | Wht Knock Sensor | Knock input | — |
| 3L | Grn Intake Air Temperature Senor | MAT input | — |
| 3K | Grn / Ora MAF signal | Aux Temp | — |
| 3J | Brn / Red Power GND | PGND | — |
| 3I | Brn / Wht TPS 5V | TPS 5V | — |
| 3H | Grn / Yel MAP signal | MAP signal input | — |
| 3G | Blk / Grn TPS Full Range | TPS signal input | — |
| 3F | Grn / Red TPS Narrow Range | SVSS1 | Can be used for flex fuel sensor input or front left wheel speed input for traction control |
| 3E | Grn / Wht Coolant Temp Sensor | ECT | — |
| 3D | — | — | — |
| 3C | Blk Oxygen Sensor Input | O2 signal Input | — |
| 3B | Grn / Red Sensor GND | SGND | — |
| 3A | Grn / Red Oil Metering Pump Sensor | Ext In | — |
| 1V / V | Blu IGF ignition feedback | — | — |
| 1U / U | Brn / Yel Mileage Sensor 2 | — | — |
| 1T / T | Blk / Blu brake light switch | Digital Input 5 | — |
| 1S / S | Red / Blk Fog Lamp Switch | Digital Input 6 | Electrical load input |
| 1R / R | Grn / Blk Neutral Switch | Digital Input 2 | — |
| 1Q / Q | Grn / Red Clutch Switch | Digital Input 1 | — |
| 1P / P | Blk / Yel Heat Hazard | — | — |
| 1O / O | Blu / Ora A/C request | Digital Input 4 | This triggers digital input 4, after inversion, and also drives the A/C clutch output |
| 1N / N | LtGrn / Blk Steering Pressure Sensor | Digital Input 3 | Engine load input |
| 1M / M | Blu Speedometer | MVSS1 | If converting to 4 wheel speed inputs, this should be the rear left wheel speed input. |
| 1L / L | Blk / Wht A/C Relay | AC Relay Output | Driven by AC input |
| 1K / K | Grn / Red Fuel Pump Relay (Speed) | — | — |
| 1J / J | Brn / Yel Igniter Trailing select | Igniter Output 3 | If converting to direct fire, this becomes the trailing output for rotor 2. |
| 1I / I | Ora Data Link Connector | Igniter Output 4 | Not used on factory, but can use this pin for conversion to direct fire for leading ignition, rotor 2 (you lose the switch solenoid output then). This wire comes out at the diagnostic connector (orange wire) |
| 1H / H | Brn Igniter Leading | Igniter Output 1 | When converting to direct fire, this output becomes the trigger for leading ignition on rotor 1 (front) |
| 1G / G | Brn Igniter Trailing | Igniter Output 2 | If converting to direct fire, this becomes the trailing output for rotor 1. |
| 1F / F | Yel / Blk Data Link Connector | MVSS2 | If converting to 4 wheel speed inputs, this should be the rear right wheel speed input |
| 1E / E | Check light | Aux Ouptut 6 | — |
| 1D / D | Yel Data Link Connector | CAS 3, for flex fuel | This pin comes out at the the diagnostic connector (yellow wire). |
| 1C / C | Blk / Red starter interlock switch | — | — |
| 1B / B | Blk / Wht Main Relay | +12 Ignition | Output from EFI relay |
| 1A / A | Blu / Red constant power | Const 12V | Straight from battery via fuse |