Removed text is struck through; added text is highlighted.
Manufacturer product image of NS13X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
S13Link header and expansion connector schedules
From Link’s S13Link installation manual, pages 15–17. Link views the ECU from the wire side. The cited table distinguishes S13 CA18DET and S14 SR20DET uses; confirm the exact header and engine before wiring. Only source-listed positions are shown and “nc” is reproduced from Link.
PinECU channelVehicle function1Ignition 1Ignition2Ignition 2Ignition3Ignition 3Ignition4Injector 5 (Aux)ISC solenoid5Aux 1Boost solenoid S13 CA18DET only6Injector 6 (Aux)A/C out7Aux 2Tacho8Aux 3Intake runner control S13 CA18DET9Injector 6 (Aux)A/C out10Ground11Ignition 3 or 4 (via J1)Ignition12Ignition 4Ignition13nc14nc15nc16ECCS relay controlPulls to ground with ignition on17nc18Aux 4Fuel pump relay19Aux 3Engine fan low speed S14 SR20DET20Ground21nc22nc23Knock 1Knock24ncnc25Aux 6Boost solenoid S14 SR20DET26GroundAFM27An Volt 4AFM signal28An Temp 1ECT29An Volt 1Oxygen signal30Ground (signal)31nc32Aux 7CE light S14 SR20DET33Aux 8CAT light / engine fan high S14 SR20DET34DI 1Power steering switch S14 SR20DET35An Volt 2Factory MAP sensor S14 SR20DET36nc37nc38An Volt 5TPS39nc40nc41Trig 2Trig 242Trig 1Trig 143DI 3Start signal44nc4512 V ignition switch inputControls pin 1646DI 4A/C in47nc48+5 V Out49+14 V ECCS relayECU power50Ground (signal)51Trig 2Trig 252Trig 1Trig 153DI 2Vehicle speed54nc55An Temp 2Factory IAT some S13 CA18DET56nc57nc58nc59+14 V ECCS relayECU power60Ground (signal)101Injector 1Injection102nc103Injector 3Injection104nc105nc106Injector 5 (Aux)ISC solenoid107Ground108Ground109+12 V constantISC flywheeling110Injector 2Injection111nc112Injector 4Injection113Aux 5VTC cam solenoid S14 SR20DET114nc115GroundO2 heater116Ground
Aux 3 appears on both 8 and 19 with different vehicle functions. Ignition 3 or 4 on 11 depends on jumper J1. Injector drives 7 and 8 are not exposed and lack injector-drive hardware. On-board MAP uses An Volt 3.
Expansion connector
PinECU channel1Ground (signal)2+5 V Out3DI 54DI 65DI 76An Volt 67An Temp 48An Temp 39Ignition 510Ignition 611Ignition 712Ignition 813An Volt 814An Volt 915An Volt 1016An Volt 11
CAN 1 / RS232
PinFunction / cable colour1Comms GND (brown)2CAN1 L (green)3CAN1 H (white)4RS232 RX (grey)5RS232 TX (yellow)
CAN 2 / OBD
PinFunction / cable colour1GND (brown)2CAN2 L (green)3CAN2 H (white)4NC (grey)5+14 V (yellow)
Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Link G4X NS13X plug-in ECUManufacturer product image of NS13X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
S13Link header and expansion connector schedules
From Link’s S13Link installation manual, pages 15–17. Link views the ECU from the wire side. The cited table distinguishes S13 CA18DET and S14 SR20DET uses; confirm the exact header and engine before wiring. Only source-listed positions are shown and “nc” is reproduced from Link.
Pin
ECU channel
Vehicle function
1
Ignition 1
Ignition
2
Ignition 2
Ignition
3
Ignition 3
Ignition
4
Injector 5 (Aux)
ISC solenoid
5
Aux 1
Boost solenoid S13 CA18DET only
6
Injector 6 (Aux)
A/C out
7
Aux 2
Tacho
8
Aux 3
Intake runner control S13 CA18DET
9
Injector 6 (Aux)
A/C out
10
Ground
11
Ignition 3 or 4 (via J1)
Ignition
12
Ignition 4
Ignition
13
nc
14
nc
15
nc
16
ECCS relay control
Pulls to ground with ignition on
17
nc
18
Aux 4
Fuel pump relay
19
Aux 3
Engine fan low speed S14 SR20DET
20
Ground
21
nc
22
nc
23
Knock 1
Knock
24
nc
nc
25
Aux 6
Boost solenoid S14 SR20DET
26
Ground
AFM
27
An Volt 4
AFM signal
28
An Temp 1
ECT
29
An Volt 1
Oxygen signal
30
Ground (signal)
31
nc
32
Aux 7
CE light S14 SR20DET
33
Aux 8
CAT light / engine fan high S14 SR20DET
34
DI 1
Power steering switch S14 SR20DET
35
An Volt 2
Factory MAP sensor S14 SR20DET
36
nc
37
nc
38
An Volt 5
TPS
39
nc
40
nc
41
Trig 2
Trig 2
42
Trig 1
Trig 1
43
DI 3
Start signal
44
nc
45
12 V ignition switch input
Controls pin 16
46
DI 4
A/C in
47
nc
48
+5 V Out
49
+14 V ECCS relay
ECU power
50
Ground (signal)
51
Trig 2
Trig 2
52
Trig 1
Trig 1
53
DI 2
Vehicle speed
54
nc
55
An Temp 2
Factory IAT some S13 CA18DET
56
nc
57
nc
58
nc
59
+14 V ECCS relay
ECU power
60
Ground (signal)
101
Injector 1
Injection
102
nc
103
Injector 3
Injection
104
nc
105
nc
106
Injector 5 (Aux)
ISC solenoid
107
Ground
108
Ground
109
+12 V constant
ISC flywheeling
110
Injector 2
Injection
111
nc
112
Injector 4
Injection
113
Aux 5
VTC cam solenoid S14 SR20DET
114
nc
115
Ground
O2 heater
116
Ground
Aux 3 appears on both 8 and 19 with different vehicle functions. Ignition 3 or 4 on 11 depends on jumper J1. Injector drives 7 and 8 are not exposed and lack injector-drive hardware. On-board MAP uses An Volt 3.
Expansion connector
Pin
ECU channel
1
Ground (signal)
2
+5 V Out
3
DI 5
4
DI 6
5
DI 7
6
An Volt 6
7
An Temp 4
8
An Temp 3
9
Ignition 5
10
Ignition 6
11
Ignition 7
12
Ignition 8
13
An Volt 8
14
An Volt 9
15
An Volt 10
16
An Volt 11
CAN 1 / RS232
Pin
Function / cable colour
1
Comms GND (brown)
2
CAN1 L (green)
3
CAN1 H (white)
4
RS232 RX (grey)
5
RS232 TX (yellow)
CAN 2 / OBD
Pin
Function / cable colour
1
GND (brown)
2
CAN2 L (green)
3
CAN2 H (white)
4
NC (grey)
5
+14 V (yellow)
Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.
Revision 3: Link G4X NS13X plug-in ECUManufacturer product image of NS13X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X NS13X is a vehicle-specific programmable plug-in ECU for the Nissan S13 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's NS13X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The NS13X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
S13Link header and expansion connector schedules
From Link’s S13Link installation manual, pages 15–17. Link views the ECU from the wire side. The cited table distinguishes S13 CA18DET and S14 SR20DET uses; confirm the exact header and engine before wiring. Only source-listed positions are shown and “nc” is reproduced from Link.
Pin
ECU channel
Vehicle function
1
Ignition 1
Ignition
2
Ignition 2
Ignition
3
Ignition 3
Ignition
4
Injector 5 (Aux)
ISC solenoid
5
Aux 1
Boost solenoid S13 CA18DET only
6
Injector 6 (Aux)
A/C out
7
Aux 2
Tacho
8
Aux 3
Intake runner control S13 CA18DET
9
Injector 6 (Aux)
A/C out
10
Ground
11
Ignition 3 or 4 (via J1)
Ignition
12
Ignition 4
Ignition
13
nc
14
nc
15
nc
16
ECCS relay control
Pulls to ground with ignition on
17
nc
18
Aux 4
Fuel pump relay
19
Aux 3
Engine fan low speed S14 SR20DET
20
Ground
21
nc
22
nc
23
Knock 1
Knock
24
nc
nc
25
Aux 6
Boost solenoid S14 SR20DET
26
Ground
AFM
27
An Volt 4
AFM signal
28
An Temp 1
ECT
29
An Volt 1
Oxygen signal
30
Ground (signal)
31
nc
32
Aux 7
CE light S14 SR20DET
33
Aux 8
CAT light / engine fan high S14 SR20DET
34
DI 1
Power steering switch S14 SR20DET
35
An Volt 2
Factory MAP sensor S14 SR20DET
36
nc
37
nc
38
An Volt 5
TPS
39
nc
40
nc
41
Trig 2
Trig 2
42
Trig 1
Trig 1
43
DI 3
Start signal
44
nc
45
12 V ignition switch input
Controls pin 16
46
DI 4
A/C in
47
nc
48
+5 V Out
49
+14 V ECCS relay
ECU power
50
Ground (signal)
51
Trig 2
Trig 2
52
Trig 1
Trig 1
53
DI 2
Vehicle speed
54
nc
55
An Temp 2
Factory IAT some S13 CA18DET
56
nc
57
nc
58
nc
59
+14 V ECCS relay
ECU power
60
Ground (signal)
101
Injector 1
Injection
102
nc
103
Injector 3
Injection
104
nc
105
nc
106
Injector 5 (Aux)
ISC solenoid
107
Ground
108
Ground
109
+12 V constant
ISC flywheeling
110
Injector 2
Injection
111
nc
112
Injector 4
Injection
113
Aux 5
VTC cam solenoid S14 SR20DET
114
nc
115
Ground
O2 heater
116
Ground
Aux 3 appears on both 8 and 19 with different vehicle functions. Ignition 3 or 4 on 11 depends on jumper J1. Injector drives 7 and 8 are not exposed and lack injector-drive hardware. On-board MAP uses An Volt 3.
Expansion connector
Pin
ECU channel
1
Ground (signal)
2
+5 V Out
3
DI 5
4
DI 6
5
DI 7
6
An Volt 6
7
An Temp 4
8
An Temp 3
9
Ignition 5
10
Ignition 6
11
Ignition 7
12
Ignition 8
13
An Volt 8
14
An Volt 9
15
An Volt 10
16
An Volt 11
CAN 1 / RS232
Pin
Function / cable colour
1
Comms GND (brown)
2
CAN1 L (green)
3
CAN1 H (white)
4
RS232 RX (grey)
5
RS232 TX (yellow)
CAN 2 / OBD
Pin
Function / cable colour
1
GND (brown)
2
CAN2 L (green)
3
CAN2 H (white)
4
NC (grey)
5
+14 V (yellow)
Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.