| 101 | Injector for cylinder 1 | Injector Output 2 | Injectors for cyl 1 & 4 paired |
| 102 | NC | — | — |
| 103 | Injector for cylinder 3 | Injector Output 3 | Injectors for cyl 3 & 5 paired |
| 104 | Fuel pump voltage control | +5V output | Connected straight to +5V |
| 105 | Injector for cylinder 2 | Injector Output 1 | Injectors for cyl 2 & 6 paired |
| 106 | Fuel pump voltage control (GTR) | +5V output | Fuel pump voltage control 2 on GTR, connected straight to +5V |
| 107 | Injector ground | Power Ground | — |
| 108 | Injector ground | Power Ground | — |
| 109 | +12V Ignition In | Switched 12V in | Power to the ECU |
| 110 | Injector for cylinder 5 | Injector Output 3 | Injectors for cyl 3 & 5 paired |
| 111 | NC | — | — |
| 112 | Injector for cylinder 6 | Injector Output 1 | Injectors for cyl 2 & 6 paired |
| 113 | Variable valve timing (R33 GTST only) | Aux Output 3 | Can be used as spare output on GTR and R32 |
| 114 | Injector for cylinder 4 | Injector Output 2 | Injectors for cyl 1 & 4 paired |
| 115 | O2 sensor heater ground | Power Ground | Connected straight to ground |
| 116 | Injector ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | Plugs for 1 & 6 are fired together |
| 2 | To Igniter for Cylinder 5 | Ignition output 2 | Plugs for 2 & 5 are fired together |
| 3 | To Igniter for Cylinder 3 | Ignition output 3 | Plugs for 3 & 4 are fired together |
| 4 | Idle Control Valve | Aux Output 1 | — |
| 5 | Auto Transmission | Aux Temp input | — |
| 6 | NC | Aux Output 8 | Electrical fan enable on GTR only, otherwise spare output |
| 7 | Tacho out | Aux Output 6 | — |
| 8 | NC | External 0-5V input | Can be used as external input for 0-5V wideband O2 sensor |
| 9 | Aircon relay | Aux Output 4 | — |
| 10 | Ground | Power Ground | — |
| 11 | To Igniter for Cylinder 6 | Ignition output 1 | Plugs for 1 & 6 are fired together |
| 12 | To Igniter for Cylinder 2 | Ignition output 2 | Plugs for 2 & 5 are fired together |
| 13 | To Igniter for Cylinder 4 | Ignition output 3 | Plugs for 3 & 4 are fired together |
| 14 | Auto Transmission | Digital Input 6 | — |
| 15 | Auto Transmission | Digital Input 7 | — |
| 16 | ECCS relay | — | When pin 45 has 12V, this pin is pulled low to activate the ECCS main relay |
| 17 | NC | Digital Input 8 | — |
| 18 | Fuel pump relay | Aux Output 5 | — |
| 19 | Power steering load input | Digital Input 1 | Connects via J8 |
| 20 | Ignition system ground | Power Ground | — |
| 21 | TXD | Air Temp signal input on some 130mm ECUs (not connected on current ECUs) | Formerly available to add air temp signal, now open circuit |
| 22 | RXD | Aux Output 8 | Available as spare output |
| 23 | Knock sensor 1 signal (cylinders 1-3) | Knock input | Both knock sensors are connected together |
| 24 | Knock sensor 2 signal (cylinders 4-6) | Knock input | Both knock sensors are connected together |
| 25 | Boost control | Aux Output 2 | — |
| 26 | AFM GND | Sensor Ground | — |
| 27 | AFM signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor |
| 28 | Engine Coolant Temperature | ECT signal input | — |
| 29 | O2/EGO sensor signal | O2/EGO signal input | For the GTR, this is the front O2/EGO sensor |
| 30 | Sensor ground | Sensor Ground | — |
| 31 | Clock | — | — |
| 32 | Check light | Aux Output 7 | — |
| 33 | NC | — | — |
| 34 | AFM Ground on GTR | Power ground | Connects via J9 |
| 35 | Front AFM signal on GTR | No connection | Connects via J10 |
| 36 | FICD solenoid input signal on R33, Air temp input on GTR | Air Temp signal input | Connects via J11. Connect external air temp signal to this wire instead of the FICD input. |
| 37 | NC | MVSS2 | Available as flex fuel input or rear right wheel speed |
| 38 | TPS signal | TPS signal input | A scaled version of this is output on pin 56 |
| 39 | NC | SVSS1 | Flex fuel or front left wheel speed |
| 40 | NC | SVSS2 | Front right wheel speed |
| 41 | 120 deg Cam Angle Sensor Signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 42 | 1 deg Cam Angle Sensor Signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 43 | Starter | — | — |
| 44 | Neutral switch | Digital Input 5 | — |
| 45 | Ignition switch | +12V Ignition | When this switches to 12V, the ECCS main relay is activated (see pin 16) |
| 46 | Aircon request input | Digital Input 2 | — |
| 47 | Check pin on CONSULT connector | CAS3 | Available as flex fuel input |
| 48 | +5V out | +5V output | +5V power supply for TPS |
| 49 | Control unit power supply | — | — |
| 50 | Control unit ground | Power Ground | — |
| 51 | 120 deg Cam Angle Sensor Signal | CAS 2 input | Connected to pin 41 internally |
| 52 | 1 deg Cam Angle Sensor Signal | CAS 1 input | Connected to pin 42 internally |
| 53 | Vehicle Speed Signal | MVSS1 | Gearbox speed sensor, or rear left wheel speed |
| 54 | Throttle Valve Switch | — | — |
| 55 | Rear O2 sensor (GTR) | O2/EGO signal input | Connected to pin 29 internally |
| 56 | Throttle sensor output signal | TPS signal (scaled by jumper J6) | TPS output signal to ALSD / ATESSA |
| 57 | Exhaust Temperature Sensor, or throttle valve switch on GTR | Sensor Ground | — |
| 58 | Battery power supply | Constant power in | — |
| 59 | Control unit power supply | — | — |
| 60 | Control unit ground | Power Ground | — |