Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Link G4X VR4X plug-in ECU
Manufacturer product image of VR4X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X VR4X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Galant VR-4 and associated applications application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's VR4X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The VR4X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

VR4Link main header and expansion connector

From Link’s VR4Link installation manual, pages 14–15. The main connector is viewed into the ECU from the wire side. Only the positions shown by Link are listed; “nc” follows its table. Check the individual vehicle harness and board before wiring.

PinECU channelVehicle function
1nc
2nc
3nc
4An Volt 4Oxygen signal
5DI 2Power steering switch
6nc
7DI 4A/C request
8An Temp 1IAT
9nc
10An Volt 2MAF signal
11nc
12nc
13nc
14nc
15nc
16nc
17Ground (signal)
18DI 3Vehicle speed
19An Volt 1TPS signal
20An Temp 2ECT
21Trig 1Trig 1
22Trig 2Trig 2
23+5 V Out
24Ground (signal)
51Injector 1Injection
52Injector 2Injection
53Aux 2EGR solenoid
54Ignition 1Ignition 1/4
55Ignition 2Ignition 2/3
56Ignition 3 (Aux)Fuel pump relay
57Ignition 4 (Aux)Fuel pressure control valve
58Aux 8ISC stepper
59Aux 7ISC stepper
60Injector 3Injection
61Injector 4Injection
62Injector 5 (Aux)Purge solenoid
63Injector 6 (Aux)ECU hold power
64Aux 3CE light
65Aux 4A/C relay
66Injector 6 (Aux)ECU hold power
67Aux 5ISC stepper
68Aux 6ISC stepper
101Ground (signal)
102+14 V main relayECU power
103nc
104nc
105Aux 1Wastegate solenoid
106Ground
107+14 V main relayECU power
108DI 1Start signal
109nc
110DI 5Ignition switch

The manual lists injector 6 (Aux) at both 63 and 66 for ECU hold power; verify the specific harness. Injector drives 7 and 8 are not exposed and lack injector-driver hardware. The on-board MAP uses An Volt 3. Link notes the ISC stepper can be reversed on some vehicles, requiring wiring or setting changes.

Expansion connector

PinChannel
1Signal ground
2+5 V Out
3nc
4DI 6
5An Volt 5
6An Volt 6
7nc
8An Temp 3

CAN 1 / RS232 connector

PinFunction / cable colour
1Comms GND (brown)
2CAN1 L (green)
3CAN1 H (white)
4RS232 RX (grey)
5RS232 TX (yellow)

Link cautions that connected serial wires can interfere with USB when CAN 1/RS232 is used for CAN.