
Link G4X EVO9X is a vehicle-specific programmable plug-in ECU for the Mitsubishi Evo IX application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's EVO9X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The EVO9X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
EVO9X header and expansion schedules
Transcribed from Link EVOLink IX manual, pages 15–17. Link gives the view into the ECU from the wire side. Pins 36–40 and 69–70 are not listed in the source; “nc” is the manual’s label. Match market and vehicle wiring before connecting.
| Pin | ECU channel | Vehicle function |
|---|---|---|
| 1 | Injector 1 | Injection |
| 2 | Injector 4 | Injection |
| 3 | Ignition 5 (Aux) | O2 heater |
| 4 | Ignition 6 (Aux) | Secondary air solenoid |
| 5 | nc | |
| 6 | Ignition 7 (Aux) | EGR valve (some models) / high-speed fan relay (EVO 8 JAP) |
| 7 | nc | |
| 8 | nc | |
| 9 | Injector 2 | Injection |
| 10 | nc | |
| 11 | Ignition 1 | Ignition cylinders 1 & 4 |
| 12 | Ignition 2 | Ignition cylinders 2 & 3 |
| 13 | nc | |
| 14 | Aux 8 | ISC stepper |
| 15 | Aux 5 | ISC stepper |
| 16 | nc | |
| 17 | nc | |
| 18 | Aux 1 | Engine fan |
| 19 | nc | |
| 20 | Injector 5 (Aux) | AC relay |
| 21 | Ignition 3 (Aux) | Fuel pump relay |
| 22 | Injector 6 (Aux) | CE lamp |
| 23 | nc | |
| 24 | Injector 3 | Injection |
| 25 | nc | |
| 26 | nc | |
| 27 | nc | |
| 28 | Aux 7 | ISC stepper |
| 29 | Aux 6 | ISC stepper |
| 30 | Ignition 4 (Aux) | Condenser fans |
| 31 | Ignition 4 (Aux) | Condenser fans |
| 32 | Aux 2 | VVC solenoid EVO IX only, not VIII JAP |
| 33 | nc | |
| 34 | Ground (signal) | |
| 35 | nc | |
| 41 | Aux 3 | Wastegate solenoids |
| 42 | +5 V Out | |
| 43 | Trig 1 | Trig 1 |
| 44 | An Temp 1 | ECT |
| 45 | Tacho | From Trig 1 |
| 46 | Ground | |
| 47 | +14 V Unreg | ECU power |
| 48 | nc | |
| 49 | Ground | TPS / MAP |
| 50 | Trig 2 | Trig 2 |
| 51 | nc | |
| 52 | nc | |
| 53 | DI 1 | Inlet cam position EVO IX only, not VIII JAP |
| 54 | An Volt 5 | Power steering switch |
| 55 | Aux 12 | Fuel pump speed relay |
| 56 | Injector 7 (Aux) | Intercooler spray relay |
| 57 | Injector 8 (Aux) | ECU hold power |
| 58 | Ground | |
| 59 | +14 V Unreg | ECU power |
| 60 | nc | |
| 61 | An Volt 2 | MAF signal |
| 62 | An Temp 3 | MAF IAT |
| 63 | Aux 3 | Wastegate solenoids |
| 64 | nc | |
| 65 | nc | |
| 66 | DI 2 | Intercooler auto switch |
| 67 | DI 7 | Intercooler manual switch |
| 68 | DI 5 | Start signal |
| 71 | An Volt 4 | Front oxygen signal |
| 72 | nc | |
| 73 | nc | |
| 74 | nc | |
| 75 | Ground | |
| 76 | nc | |
| 77 | nc | |
| 78 | An Volt 3 | TPS signal |
| 79 | nc | |
| 80 | DI 3 | Vehicle speed |
| 81 | nc | |
| 82 | nc | |
| 83 | DI 4 | A/C request |
| 84 | nc | |
| 85 | nc | |
| 86 | nc | |
| 87 | nc | |
| 88 | DI 8 | Clutch switch |
| 89 | nc | |
| 90 | Ignition 8 (Aux) | Intercooler spray lamp |
| 91 | Knock 1 | Knock |
| 92 | An Volt 1 via jumper | MAP factory sensor |
| 93 | nc | |
| 94 | nc | |
| 95 | nc | |
| 96 | An Temp 2 | IAT EVO IX JAP/US only |
| 97 | nc | |
| 98 | nc | |
| 99 | DI 6 | Ignition switch |
| 100 | nc |
Pin 92 factory MAP and the on-board MAP both use An Volt 1 via a selector jumper. The manual repeats condenser fan Ignition 4 at 30/31 and wastegate Aux 3 at 41/63; identify the applicable loom. Injector 8 has hold-power hardware and is unsuitable for injector drive without modification.
Expansion connector
| Pin | ECU channel |
|---|---|
| 1 | Ground (signal) |
| 2 | +5 V Out |
| 3 | DI 9 |
| 4 | DI 10 |
| 5 | Aux 11 |
| 6 | An Volt 11 |
| 7 | An Volt 8 |
| 8 | An Temp 4 |
| 9 | Ground (signal) |
| 10 | +5 V Out |
| 11 | Aux 9 |
| 12 | Aux 10 |
| 13 | An Volt 6 |
| 14 | An Volt 7 |
| 15 | An Volt 9 |
| 16 | An Volt 10 |
CAN 1 / RS232
| Pin | Function / cable colour |
|---|---|
| 1 | Comms GND (brown) |
| 2 | CAN1 L (green) |
| 3 | CAN1 H (white) |
| 4 | RS232 RX (grey) |
| 5 | RS232 TX (yellow) |
CAN 2 / OBD
| Pin | Function / cable colour |
|---|---|
| 1 | GND (brown) |
| 2 | CAN2 L (green) |
| 3 | CAN2 H (white) |
| 4 | NC (grey) |
| 5 | +14 V (yellow) |
Link cautions that connected serial wires can interfere with USB when CAN 1 is used for CAN.