Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Haltech standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
Haltech E6X is a E series programmable engine-management model. Haltech's specification describes programmable fuel and ignition, eight injector drivers, four dedicated PWM outputs, staged and up-to-four-bank sequential injection, and distributor, direct-fire or wasted-spark modes within specified engine limits. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E6X wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedule
These are the 36 positions from the Haltech E6X main harness wiring diagram. The diagram identifies the E6X main harness as revision A, 5 November 2008. It depicts a separate nine-way PC interface, with pins 2 TX, 3 RX and 5 ground. ECU power is shown at pins 7 and 25; consult the diagram for the fused supply and branching. This schedule is specific to the E6X; similarly numbered positions differ on the E6K and E6X. The diagram also documents the harness-side sensor, ignition, injector and relay connectors.
ECU pinFunctionHarness colour where documented1Spare A/DRed/black2O2 sensorGrey, shielded3PWM out 2Pink/black4PWM out 1Violet/white5Road speedGrey/yellow, shielded6TriggerYellow, shielded7+13 V DC ECUSee diagram8TXRed in shielded cable9RXBlue in shielded cable10TrimBlack/white11MAPYellow12Ignition 4Blue/yellow13HomeGreen, shielded14IDL 4Brown/white15IDL 3Yellow/red16IDL 2Green/yellow17IDL 1Brown18+5 V sensor supplyOrange19Injector 1Light blue20Injector 2Blue/red21Injector 3Green/red22Injector 4Pink23PWM out 3Blue/green24PWM out 4Green/white25+13 V DC ECURed/white26GroundBlack27Auxiliary outGreen/black28Auxiliary inGreen29Air temperatureGrey30CoolantViolet31Throttle positionWhite32ECU groundSee diagram33Pump relay triggerBlack/yellow34Ignition 3 / digital out 2Blue35Ignition 2 / digital out 1White/black36Ignition 1Light green
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Haltech E6X
Haltech E6X is a E series programmable engine-management model. Haltech's specification describes programmable fuel and ignition, eight injector drivers, four dedicated PWM outputs, staged and up-to-four-bank sequential injection, and distributor, direct-fire or wasted-spark modes within specified engine limits. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E6X wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedule
These are the 36 positions from the Haltech E6X main harness wiring diagram. The diagram identifies the E6X main harness as revision A, 5 November 2008. It depicts a separate nine-way PC interface, with pins 2 TX, 3 RX and 5 ground. ECU power is shown at pins 7 and 25; consult the diagram for the fused supply and branching. This schedule is specific to the E6X; similarly numbered positions differ on the E6K and E6X. The diagram also documents the harness-side sensor, ignition, injector and relay connectors.
| ECU pin | Function | Harness colour where documented |
|---|
| 1 | Spare A/D | Red/black |
| 2 | O2 sensor | Grey, shielded |
| 3 | PWM out 2 | Pink/black |
| 4 | PWM out 1 | Violet/white |
| 5 | Road speed | Grey/yellow, shielded |
| 6 | Trigger | Yellow, shielded |
| 7 | +13 V DC ECU | See diagram |
| 8 | TX | Red in shielded cable |
| 9 | RX | Blue in shielded cable |
| 10 | Trim | Black/white |
| 11 | MAP | Yellow |
| 12 | Ignition 4 | Blue/yellow |
| 13 | Home | Green, shielded |
| 14 | IDL 4 | Brown/white |
| 15 | IDL 3 | Yellow/red |
| 16 | IDL 2 | Green/yellow |
| 17 | IDL 1 | Brown |
| 18 | +5 V sensor supply | Orange |
| 19 | Injector 1 | Light blue |
| 20 | Injector 2 | Blue/red |
| 21 | Injector 3 | Green/red |
| 22 | Injector 4 | Pink |
| 23 | PWM out 3 | Blue/green |
| 24 | PWM out 4 | Green/white |
| 25 | +13 V DC ECU | Red/white |
| 26 | Ground | Black |
| 27 | Auxiliary out | Green/black |
| 28 | Auxiliary in | Green |
| 29 | Air temperature | Grey |
| 30 | Coolant | Violet |
| 31 | Throttle position | White |
| 32 | ECU ground | See diagram |
| 33 | Pump relay trigger | Black/yellow |
| 34 | Ignition 3 / digital out 2 | Blue |
| 35 | Ignition 2 / digital out 1 | White/black |
| 36 | Ignition 1 | Light green |
Revision 2: Haltech E6X
Haltech E6X is a E series programmable engine-management model. Haltech's specification describes programmable fuel and ignition, eight injector drivers, four dedicated PWM outputs, staged and up-to-four-bank sequential injection, and distributor, direct-fire or wasted-spark modes within specified engine limits. Manufacturer specification or guide.
Identification and output allocation
Record the full ECU label, serial number, hardware or harness revision, software and existing calibration. These characteristics are model-specific; a superficially similar E series ECU should not be treated as a drop-in replacement. Counts can be limited by shared outputs, external modules and the engine's ignition and injection strategy.
Model-specific pinout and wiring
Consult the E6X wiring documentation and the historic model manuals and connector archive where applicable. Select the named model and the precise harness revision; read its numbered connector view, driver characteristics, injector supply, power and ground notes. The connector appearance alone is not proof of identical pin functions.
Software and further information
legacy software matching the model. Haltech's download centre separates software and provides a legacy section. See Haltech standalone ECUs for the other families.
Manufacturer connector schedule
These are the 36 positions from the Haltech E6X main harness wiring diagram. The diagram identifies the E6X main harness as revision A, 5 November 2008. It depicts a separate nine-way PC interface, with pins 2 TX, 3 RX and 5 ground. ECU power is shown at pins 7 and 25; consult the diagram for the fused supply and branching. This schedule is specific to the E6X; similarly numbered positions differ on the E6K and E6X. The diagram also documents the harness-side sensor, ignition, injector and relay connectors.
| ECU pin | Function | Harness colour where documented |
|---|
| 1 | Spare A/D | Red/black |
| 2 | O2 sensor | Grey, shielded |
| 3 | PWM out 2 | Pink/black |
| 4 | PWM out 1 | Violet/white |
| 5 | Road speed | Grey/yellow, shielded |
| 6 | Trigger | Yellow, shielded |
| 7 | +13 V DC ECU | See diagram |
| 8 | TX | Red in shielded cable |
| 9 | RX | Blue in shielded cable |
| 10 | Trim | Black/white |
| 11 | MAP | Yellow |
| 12 | Ignition 4 | Blue/yellow |
| 13 | Home | Green, shielded |
| 14 | IDL 4 | Brown/white |
| 15 | IDL 3 | Yellow/red |
| 16 | IDL 2 | Green/yellow |
| 17 | IDL 1 | Brown |
| 18 | +5 V sensor supply | Orange |
| 19 | Injector 1 | Light blue |
| 20 | Injector 2 | Blue/red |
| 21 | Injector 3 | Green/red |
| 22 | Injector 4 | Pink |
| 23 | PWM out 3 | Blue/green |
| 24 | PWM out 4 | Green/white |
| 25 | +13 V DC ECU | Red/white |
| 26 | Ground | Black |
| 27 | Auxiliary out | Green/black |
| 28 | Auxiliary in | Green |
| 29 | Air temperature | Grey |
| 30 | Coolant | Violet |
| 31 | Throttle position | White |
| 32 | ECU ground | See diagram |
| 33 | Pump relay trigger | Black/yellow |
| 34 | Ignition 3 / digital out 2 | Blue |
| 35 | Ignition 2 / digital out 1 | White/black |
| 36 | Ignition 1 | Light green |