Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Ford Focus RS ST Mk2 S7Plus, with product code S7plus-ST/RS. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Ford Focus RS ST Mk2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Focus Mk2 kit ECU connector schedule

The Syvecs Focus Mk2 manual, version 1.2, says the kit is designed for RS and ST; its table is labelled “FocusRS Notes”. These are the Syvecs ECU connectors, not Ford's OEM connector positions. For an ST installation, confirm vehicle-specific assignments with Syvecs. Blank cells mean no kit function is identified in this manual.

Connector A — 34 way

PinSyvecs I/ORS kit function in source
A1PWR CTR OUTMain relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3—
A5H-Bridge4 / SlaveOut4—
A6H-Bridge5 / SlaveOut5—
A7H-Bridge6 / SlaveOut6—
A8H-Bridge7 / SlaveOut7—
A9H-Bridge8 / SlaveOut8—
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Reverse gear switch
A16FUEL7Secondary injector 1 or spare
A17FUEL8Secondary injector 2 or spare
A18PWM1 / *FUEL9Fuel pump
A19PWM2 / *FUEL10Fan
A20PWM3 / *FUEL11Boost solenoids 1 and 2
A21PWM4 / *FUEL12A/C clutch
A22PWM5Starter relay
A23PWM6—
A24PWM7VVT intake
A25PWM8VVT exhaust
A26IGN1Cylinder 1 ignition output
A27IGN2Cylinder 2 ignition output
A28IGN3Cylinder 3 ignition output
A29IGN4Cylinder 4 ignition output
A30IGN5Cylinder 5 ignition output
A31IGN6—
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDSee end of pinouts in source

Connector B — 26 way

PinSyvecs I/ORS kit function in source
B1PWRGND—
B2——
B3——
B4KNOCK—
B5KNOCK 2—
B6PVBAT—
B7IVBAT—
B8LAM1A—
B9LAM1B—
B10LAM1C—
B11LAM1D—
B12LAM1HEATER—
B13IVBAT—
B14LAM2A—
B15LAM2B—
B16LAM2C—
B17LAM2D—
B18LAM2HEATER—
B19IVBAT—
B20KLINEAlternator LIN
B21RS232RX—
B22RS232TX—
B23LANRX−—
B24LANRX+—
B25LANTX−—
B26LANTX+—

Connector C — 34 way

PinSyvecs I/ORS kit function in source
C1KNOCK GROUND—
C2ANGND—
C3ANGND—
C4ANGND—
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01Crank
C11AN02Oil pressure switch
C12AN03MAP sensor
C13AN04—
C14AN05PPSa
C15AN06—
C16AN07Inlet cam sensor
C17AN08Exhaust cam
C18AN09TPS input
C19AN10—
C20AN11TPS 2 input
C21AN12—
C22AN13Coolant temperature input
C23AN14—
C24AN15Air temperature
C25AN16Fuel pressure
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01—
C30AN S2 / Slave An02—
C31AN S3 / Slave An03—
C32AN S4 / Slave An04—
C33AN S5 / Slave An05—
C34AN S6 / Slave An06—

The manual leaves B2 and B3 unlabelled and refers to an end-of-pinout note for A34; it does not supply these missing details in the chart. Confirm them with Syvecs for the actual kit.