Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 350Z DE HR S7Plus, with product code S7Plus-N350z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan 350Z DE HR S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Syvecs Nissan 350Z DE HR S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index

DE and HR kit ECU connector schedules

The Syvecs Nissan 350Z manual, version 1.2, pages 4–8, gives different DE and HR ECU schedules. These are Syvecs ECU-side connector positions, not the Nissan vehicle-harness pinout. Identify the exact engine and kit; B2/B3, for example, are CAN2 on the DE chart and thermocouple EGT2 on the HR chart. Blank notes reproduce unspecified cells in the manual.

DE engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source noteA1PWR CTR OUTMain relayA2H-Bridge1 / SlaveOut1DBW+A3H-Bridge2 / SlaveOut2DBW−A4H-Bridge3 / SlaveOut3—A5H-Bridge4 / SlaveOut4—A6H-Bridge5 / SlaveOut5—A7H-Bridge6 / SlaveOut6—A8H-Bridge7 / SlaveOut7—A9H-Bridge8 / SlaveOut8—A10FUEL1Cylinder 1 injectorA11FUEL2Cylinder 2 injectorA12FUEL3Cylinder 3 injectorA13FUEL4Cylinder 4 injectorA14FUEL5Cylinder 5 injectorA15FUEL6Cylinder 6 injectorA16FUEL7—A17FUEL8—A18PWM1 / *FUEL9Fuel pumpA19PWM2 / *FUEL10Throttle control relayA20PWM3 / *FUEL11—A21PWM4 / *FUEL12—A22PWM5 / *FUEL13VVTi 2; flyback solder bridge setA23PWM6 / *FUEL14VVTi 1; flyback solder bridge setA24PWM7 / *FUEL15VVT exhaust; flyback solder bridge setA25PWM8 / *FUEL16VVT2 exhaust; flyback solder bridge setA26IGN1Ignition 1A27IGN2Ignition 2A28IGN3Ignition 3A29IGN4Ignition 4A30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDECU groundA33PWRGNDECU groundA34PWRGND—

Connector B — 26 way

PinSyvecs I/OKit function / source noteB1PWRGNDPower groundB2CAN2L—B3CAN2H—B4KNOCKKnock sensor inputB5KNOCK 2—B6PVBAT—B7IVBAT12 V from ECMB8LAM1ABlack lambda LSUB9LAM1BRed lambda LSUB10LAM1C—B11LAM1DLambda groundB12LAM1HEATERGray LSUB13IVBAT12 V from ECMB14LAM2ABlack lambda LSUB15LAM2BRed lambda LSUB16LAM2C—B17LAM2DLambda groundB18LAM2HEATERGray LSUB19IVBAT—B20KLINE—B21RS232RX—B22RS232TX—B23LANRX−—B24LANRX+—B25LANTX−—B26LANTX+—

Connector C — 34 way

PinSyvecs I/OKit function / source noteC1KNOCK GROUND—C2ANGNDSensor groundC3ANGNDCam and crank groundC4ANGND—C55V OUTSensor supplyC65V OUTSensor supplyC75V OUT—C8CAN L—C9CAN H—C10AN01CrankC11AN02Cam 1C12AN03Cam 2C13AN04—C14AN05MAF sensorC15AN06Exhaust cam position 1C16AN07Power steering (MAP)C17AN08Exhaust cam position 2C18AN09TPS1AC19AN10TPS1BC20AN11PPSAC21AN12PPSBC22AN13Coolant temperature inputC23AN14Air temperature inputC24AN15Steering wheel switchC25AN16Oil temperatureC26EGT1−—C27EGT1+—C28PWR CTR INIgnition switchC29AN S1 / Slave An01—C30AN S2 / Slave An02Fuel temperatureC31AN S3 / Slave An03—C32AN S4 / Slave An04—C33AN S5 / Slave An05—C34AN S6 / Slave An06Brake switch

HR engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source noteA1PWR CTR OUTThrottle and main relayA2H-Bridge1 / SlaveOut1DBWA3H-Bridge2 / SlaveOut2DBWA4H-Bridge3 / SlaveOut3DBWA5H-Bridge4 / SlaveOut4DBWA6H-Bridge5 / SlaveOut5Boost solenoidA7H-Bridge6 / SlaveOut6Fuel pump 2A8H-Bridge7 / SlaveOut7EvapA9H-Bridge8 / SlaveOut8TachoA10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Primary injector 5A15FUEL6Primary injector 6A16FUEL7Secondary injector 1 or spareA17FUEL8Secondary injector 2 or spareA18PWM1 / *FUEL9Secondary injector 3 or spareA19PWM2 / *FUEL10Secondary injector 4 or spareA20PWM3 / *FUEL11Secondary injector 5 or spareA21PWM4 / *FUEL12Secondary injector 6 or spareA22PWM5VVT1 exhaustA23PWM6VVT2 exhaustA24PWM7VVT1 intakeA25PWM8VVT2 intakeA26IGN1Ignition 1A27IGN2Ignition 2A28IGN3Ignition 3A29IGN4Ignition 4A30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source noteB1PWRGNDPower groundB2EGT2+K-type thermocoupleB3EGT2−K-type thermocoupleB4KNOCK—B5KNOCK 2—B6PVBATConstant 12 VB7IVBAT12 VB8LAM1A2.2 V per sourceB9LAM1B1.8 V per sourceB10LAM1C—B11LAM1D—B12LAM1HEATERDenso heaterB13IVBAT12 VB14LAM2A2.2 V per sourceB15LAM2B1.8 V per sourceB16LAM2C—B17LAM2D—B18LAM2HEATERDenso heaterB19IVBAT12 VB20KLINE—B21RS232RX—B22RS232TX—B23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source noteC1KNOCKGNDKnock groundC2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT—C65V OUT—C75V OUT—C8CAN L—C9CAN H—C10AN01TPS1AC11AN02Cam 1 exhaust positionC12AN03TPS2AC13AN04Cam 2 exhaust positionC14AN05Cam position sensorC15AN06Crank position sensorC16AN07Cam 2 position sensorC17AN08—C18AN09MAP absolute sensorC19AN10PPS1C20AN11PPS2C21AN12—C22AN13Intake temperatureC23AN14Air charge temperatureC24AN15Coolant temperatureC25AN16Cruise control switchC26EGT1−—C27EGT1+—C28PWR CTR INIgnition switchC29AN S1 / Slave An01Oil temperatureC30AN S2 / Slave An02TPS1BC31AN S3 / Slave An03TPS2BC32AN S4 / Slave An04Brake switchC33AN S5 / Slave An05—C34AN S6 / Slave An06—

The HR section repeats lambda-1 software labels in the second-lambda rows; verify wiring and assigned sensor type with Syvecs. Follow the source diagram and the exact kit configuration for sensor polarity, current limits and solder-bridge settings.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs Nissan 350Z DE HR S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 350Z DE HR S7Plus, with product code S7Plus-N350z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan 350Z DE HR S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

DE and HR kit ECU connector schedules

The Syvecs Nissan 350Z manual, version 1.2, pages 4–8, gives different DE and HR ECU schedules. These are Syvecs ECU-side connector positions, not the Nissan vehicle-harness pinout. Identify the exact engine and kit; B2/B3, for example, are CAN2 on the DE chart and thermocouple EGT2 on the HR chart. Blank notes reproduce unspecified cells in the manual.

DE engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTMain relay
A2H-Bridge1 / SlaveOut1DBW+
A3H-Bridge2 / SlaveOut2DBW−
A4H-Bridge3 / SlaveOut3—
A5H-Bridge4 / SlaveOut4—
A6H-Bridge5 / SlaveOut5—
A7H-Bridge6 / SlaveOut6—
A8H-Bridge7 / SlaveOut7—
A9H-Bridge8 / SlaveOut8—
A10FUEL1Cylinder 1 injector
A11FUEL2Cylinder 2 injector
A12FUEL3Cylinder 3 injector
A13FUEL4Cylinder 4 injector
A14FUEL5Cylinder 5 injector
A15FUEL6Cylinder 6 injector
A16FUEL7—
A17FUEL8—
A18PWM1 / *FUEL9Fuel pump
A19PWM2 / *FUEL10Throttle control relay
A20PWM3 / *FUEL11—
A21PWM4 / *FUEL12—
A22PWM5 / *FUEL13VVTi 2; flyback solder bridge set
A23PWM6 / *FUEL14VVTi 1; flyback solder bridge set
A24PWM7 / *FUEL15VVT exhaust; flyback solder bridge set
A25PWM8 / *FUEL16VVT2 exhaust; flyback solder bridge set
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDECU ground
A33PWRGNDECU ground
A34PWRGND—

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCKKnock sensor input
B5KNOCK 2—
B6PVBAT—
B7IVBAT12 V from ECM
B8LAM1ABlack lambda LSU
B9LAM1BRed lambda LSU
B10LAM1C—
B11LAM1DLambda ground
B12LAM1HEATERGray LSU
B13IVBAT12 V from ECM
B14LAM2ABlack lambda LSU
B15LAM2BRed lambda LSU
B16LAM2C—
B17LAM2DLambda ground
B18LAM2HEATERGray LSU
B19IVBAT—
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−—
B24LANRX+—
B25LANTX−—
B26LANTX+—

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCK GROUND—
C2ANGNDSensor ground
C3ANGNDCam and crank ground
C4ANGND—
C55V OUTSensor supply
C65V OUTSensor supply
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01Crank
C11AN02Cam 1
C12AN03Cam 2
C13AN04—
C14AN05MAF sensor
C15AN06Exhaust cam position 1
C16AN07Power steering (MAP)
C17AN08Exhaust cam position 2
C18AN09TPS1A
C19AN10TPS1B
C20AN11PPSA
C21AN12PPSB
C22AN13Coolant temperature input
C23AN14Air temperature input
C24AN15Steering wheel switch
C25AN16Oil temperature
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01—
C30AN S2 / Slave An02Fuel temperature
C31AN S3 / Slave An03—
C32AN S4 / Slave An04—
C33AN S5 / Slave An05—
C34AN S6 / Slave An06Brake switch

HR engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTThrottle and main relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3DBW
A5H-Bridge4 / SlaveOut4DBW
A6H-Bridge5 / SlaveOut5Boost solenoid
A7H-Bridge6 / SlaveOut6Fuel pump 2
A8H-Bridge7 / SlaveOut7Evap
A9H-Bridge8 / SlaveOut8Tacho
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Primary injector 6
A16FUEL7Secondary injector 1 or spare
A17FUEL8Secondary injector 2 or spare
A18PWM1 / *FUEL9Secondary injector 3 or spare
A19PWM2 / *FUEL10Secondary injector 4 or spare
A20PWM3 / *FUEL11Secondary injector 5 or spare
A21PWM4 / *FUEL12Secondary injector 6 or spare
A22PWM5VVT1 exhaust
A23PWM6VVT2 exhaust
A24PWM7VVT1 intake
A25PWM8VVT2 intake
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2EGT2+K-type thermocouple
B3EGT2−K-type thermocouple
B4KNOCK—
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1A2.2 V per source
B9LAM1B1.8 V per source
B10LAM1C—
B11LAM1D—
B12LAM1HEATERDenso heater
B13IVBAT12 V
B14LAM2A2.2 V per source
B15LAM2B1.8 V per source
B16LAM2C—
B17LAM2D—
B18LAM2HEATERDenso heater
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCKGNDKnock ground
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01TPS1A
C11AN02Cam 1 exhaust position
C12AN03TPS2A
C13AN04Cam 2 exhaust position
C14AN05Cam position sensor
C15AN06Crank position sensor
C16AN07Cam 2 position sensor
C17AN08—
C18AN09MAP absolute sensor
C19AN10PPS1
C20AN11PPS2
C21AN12—
C22AN13Intake temperature
C23AN14Air charge temperature
C24AN15Coolant temperature
C25AN16Cruise control switch
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01Oil temperature
C30AN S2 / Slave An02TPS1B
C31AN S3 / Slave An03TPS2B
C32AN S4 / Slave An04Brake switch
C33AN S5 / Slave An05—
C34AN S6 / Slave An06—

The HR section repeats lambda-1 software labels in the second-lambda rows; verify wiring and assigned sensor type with Syvecs. Follow the source diagram and the exact kit configuration for sensor polarity, current limits and solder-bridge settings.

Revision 2: Syvecs Nissan 350Z DE HR S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 350Z DE HR S7Plus, with product code S7Plus-N350z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan 350Z DE HR S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

DE and HR kit ECU connector schedules

The Syvecs Nissan 350Z manual, version 1.2, pages 4–8, gives different DE and HR ECU schedules. These are Syvecs ECU-side connector positions, not the Nissan vehicle-harness pinout. Identify the exact engine and kit; B2/B3, for example, are CAN2 on the DE chart and thermocouple EGT2 on the HR chart. Blank notes reproduce unspecified cells in the manual.

DE engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTMain relay
A2H-Bridge1 / SlaveOut1DBW+
A3H-Bridge2 / SlaveOut2DBW−
A4H-Bridge3 / SlaveOut3—
A5H-Bridge4 / SlaveOut4—
A6H-Bridge5 / SlaveOut5—
A7H-Bridge6 / SlaveOut6—
A8H-Bridge7 / SlaveOut7—
A9H-Bridge8 / SlaveOut8—
A10FUEL1Cylinder 1 injector
A11FUEL2Cylinder 2 injector
A12FUEL3Cylinder 3 injector
A13FUEL4Cylinder 4 injector
A14FUEL5Cylinder 5 injector
A15FUEL6Cylinder 6 injector
A16FUEL7—
A17FUEL8—
A18PWM1 / *FUEL9Fuel pump
A19PWM2 / *FUEL10Throttle control relay
A20PWM3 / *FUEL11—
A21PWM4 / *FUEL12—
A22PWM5 / *FUEL13VVTi 2; flyback solder bridge set
A23PWM6 / *FUEL14VVTi 1; flyback solder bridge set
A24PWM7 / *FUEL15VVT exhaust; flyback solder bridge set
A25PWM8 / *FUEL16VVT2 exhaust; flyback solder bridge set
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDECU ground
A33PWRGNDECU ground
A34PWRGND—

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCKKnock sensor input
B5KNOCK 2—
B6PVBAT—
B7IVBAT12 V from ECM
B8LAM1ABlack lambda LSU
B9LAM1BRed lambda LSU
B10LAM1C—
B11LAM1DLambda ground
B12LAM1HEATERGray LSU
B13IVBAT12 V from ECM
B14LAM2ABlack lambda LSU
B15LAM2BRed lambda LSU
B16LAM2C—
B17LAM2DLambda ground
B18LAM2HEATERGray LSU
B19IVBAT—
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−—
B24LANRX+—
B25LANTX−—
B26LANTX+—

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCK GROUND—
C2ANGNDSensor ground
C3ANGNDCam and crank ground
C4ANGND—
C55V OUTSensor supply
C65V OUTSensor supply
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01Crank
C11AN02Cam 1
C12AN03Cam 2
C13AN04—
C14AN05MAF sensor
C15AN06Exhaust cam position 1
C16AN07Power steering (MAP)
C17AN08Exhaust cam position 2
C18AN09TPS1A
C19AN10TPS1B
C20AN11PPSA
C21AN12PPSB
C22AN13Coolant temperature input
C23AN14Air temperature input
C24AN15Steering wheel switch
C25AN16Oil temperature
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01—
C30AN S2 / Slave An02Fuel temperature
C31AN S3 / Slave An03—
C32AN S4 / Slave An04—
C33AN S5 / Slave An05—
C34AN S6 / Slave An06Brake switch

HR engine kit

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTThrottle and main relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3DBW
A5H-Bridge4 / SlaveOut4DBW
A6H-Bridge5 / SlaveOut5Boost solenoid
A7H-Bridge6 / SlaveOut6Fuel pump 2
A8H-Bridge7 / SlaveOut7Evap
A9H-Bridge8 / SlaveOut8Tacho
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Primary injector 6
A16FUEL7Secondary injector 1 or spare
A17FUEL8Secondary injector 2 or spare
A18PWM1 / *FUEL9Secondary injector 3 or spare
A19PWM2 / *FUEL10Secondary injector 4 or spare
A20PWM3 / *FUEL11Secondary injector 5 or spare
A21PWM4 / *FUEL12Secondary injector 6 or spare
A22PWM5VVT1 exhaust
A23PWM6VVT2 exhaust
A24PWM7VVT1 intake
A25PWM8VVT2 intake
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2EGT2+K-type thermocouple
B3EGT2−K-type thermocouple
B4KNOCK—
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1A2.2 V per source
B9LAM1B1.8 V per source
B10LAM1C—
B11LAM1D—
B12LAM1HEATERDenso heater
B13IVBAT12 V
B14LAM2A2.2 V per source
B15LAM2B1.8 V per source
B16LAM2C—
B17LAM2D—
B18LAM2HEATERDenso heater
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCKGNDKnock ground
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01TPS1A
C11AN02Cam 1 exhaust position
C12AN03TPS2A
C13AN04Cam 2 exhaust position
C14AN05Cam position sensor
C15AN06Crank position sensor
C16AN07Cam 2 position sensor
C17AN08—
C18AN09MAP absolute sensor
C19AN10PPS1
C20AN11PPS2
C21AN12—
C22AN13Intake temperature
C23AN14Air charge temperature
C24AN15Coolant temperature
C25AN16Cruise control switch
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01Oil temperature
C30AN S2 / Slave An02TPS1B
C31AN S3 / Slave An03TPS2B
C32AN S4 / Slave An04Brake switch
C33AN S5 / Slave An05—
C34AN S6 / Slave An06—

The HR section repeats lambda-1 software labels in the second-lambda rows; verify wiring and assigned sensor type with Syvecs. Follow the source diagram and the exact kit configuration for sensor polarity, current limits and solder-bridge settings.