
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 350Z DE HR S7Plus, with product code S7Plus-N350z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan 350Z DE HR S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Nissan 350Z DE HR S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
DE and HR kit ECU connector schedules
The Syvecs Nissan 350Z manual, version 1.2, pages 4–8, gives different DE and HR ECU schedules. These are Syvecs ECU-side connector positions, not the Nissan vehicle-harness pinout. Identify the exact engine and kit; B2/B3, for example, are CAN2 on the DE chart and thermocouple EGT2 on the HR chart. Blank notes reproduce unspecified cells in the manual.
DE engine kit
Connector A — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| A1 | PWR CTR OUT | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW+ |
| A3 | H-Bridge2 / SlaveOut2 | DBW− |
| A4 | H-Bridge3 / SlaveOut3 | — |
| A5 | H-Bridge4 / SlaveOut4 | — |
| A6 | H-Bridge5 / SlaveOut5 | — |
| A7 | H-Bridge6 / SlaveOut6 | — |
| A8 | H-Bridge7 / SlaveOut7 | — |
| A9 | H-Bridge8 / SlaveOut8 | — |
| A10 | FUEL1 | Cylinder 1 injector |
| A11 | FUEL2 | Cylinder 2 injector |
| A12 | FUEL3 | Cylinder 3 injector |
| A13 | FUEL4 | Cylinder 4 injector |
| A14 | FUEL5 | Cylinder 5 injector |
| A15 | FUEL6 | Cylinder 6 injector |
| A16 | FUEL7 | — |
| A17 | FUEL8 | — |
| A18 | PWM1 / *FUEL9 | Fuel pump |
| A19 | PWM2 / *FUEL10 | Throttle control relay |
| A20 | PWM3 / *FUEL11 | — |
| A21 | PWM4 / *FUEL12 | — |
| A22 | PWM5 / *FUEL13 | VVTi 2; flyback solder bridge set |
| A23 | PWM6 / *FUEL14 | VVTi 1; flyback solder bridge set |
| A24 | PWM7 / *FUEL15 | VVT exhaust; flyback solder bridge set |
| A25 | PWM8 / *FUEL16 | VVT2 exhaust; flyback solder bridge set |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | ECU ground |
| A33 | PWRGND | ECU ground |
| A34 | PWRGND | — |
Connector B — 26 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | Knock sensor input |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | — |
| B7 | IVBAT | 12 V from ECM |
| B8 | LAM1A | Black lambda LSU |
| B9 | LAM1B | Red lambda LSU |
| B10 | LAM1C | — |
| B11 | LAM1D | Lambda ground |
| B12 | LAM1HEATER | Gray LSU |
| B13 | IVBAT | 12 V from ECM |
| B14 | LAM2A | Black lambda LSU |
| B15 | LAM2B | Red lambda LSU |
| B16 | LAM2C | — |
| B17 | LAM2D | Lambda ground |
| B18 | LAM2HEATER | Gray LSU |
| B19 | IVBAT | — |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | — |
| B24 | LANRX+ | — |
| B25 | LANTX− | — |
| B26 | LANTX+ | — |
Connector C — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| C1 | KNOCK GROUND | — |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Cam and crank ground |
| C4 | ANGND | — |
| C5 | 5V OUT | Sensor supply |
| C6 | 5V OUT | Sensor supply |
| C7 | 5V OUT | — |
| C8 | CAN L | — |
| C9 | CAN H | — |
| C10 | AN01 | Crank |
| C11 | AN02 | Cam 1 |
| C12 | AN03 | Cam 2 |
| C13 | AN04 | — |
| C14 | AN05 | MAF sensor |
| C15 | AN06 | Exhaust cam position 1 |
| C16 | AN07 | Power steering (MAP) |
| C17 | AN08 | Exhaust cam position 2 |
| C18 | AN09 | TPS1A |
| C19 | AN10 | TPS1B |
| C20 | AN11 | PPSA |
| C21 | AN12 | PPSB |
| C22 | AN13 | Coolant temperature input |
| C23 | AN14 | Air temperature input |
| C24 | AN15 | Steering wheel switch |
| C25 | AN16 | Oil temperature |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition switch |
| C29 | AN S1 / Slave An01 | — |
| C30 | AN S2 / Slave An02 | Fuel temperature |
| C31 | AN S3 / Slave An03 | — |
| C32 | AN S4 / Slave An04 | — |
| C33 | AN S5 / Slave An05 | — |
| C34 | AN S6 / Slave An06 | Brake switch |
HR engine kit
Connector A — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| A1 | PWR CTR OUT | Throttle and main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | DBW |
| A5 | H-Bridge4 / SlaveOut4 | DBW |
| A6 | H-Bridge5 / SlaveOut5 | Boost solenoid |
| A7 | H-Bridge6 / SlaveOut6 | Fuel pump 2 |
| A8 | H-Bridge7 / SlaveOut7 | Evap |
| A9 | H-Bridge8 / SlaveOut8 | Tacho |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Primary injector 6 |
| A16 | FUEL7 | Secondary injector 1 or spare |
| A17 | FUEL8 | Secondary injector 2 or spare |
| A18 | PWM1 / *FUEL9 | Secondary injector 3 or spare |
| A19 | PWM2 / *FUEL10 | Secondary injector 4 or spare |
| A20 | PWM3 / *FUEL11 | Secondary injector 5 or spare |
| A21 | PWM4 / *FUEL12 | Secondary injector 6 or spare |
| A22 | PWM5 | VVT1 exhaust |
| A23 | PWM6 | VVT2 exhaust |
| A24 | PWM7 | VVT1 intake |
| A25 | PWM8 | VVT2 intake |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
Connector B — 26 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | EGT2+ | K-type thermocouple |
| B3 | EGT2− | K-type thermocouple |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | 2.2 V per source |
| B9 | LAM1B | 1.8 V per source |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | Denso heater |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | 2.2 V per source |
| B15 | LAM2B | 1.8 V per source |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | Denso heater |
| B19 | IVBAT | 12 V |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
Connector C — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| C1 | KNOCKGND | Knock ground |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | — |
| C9 | CAN H | — |
| C10 | AN01 | TPS1A |
| C11 | AN02 | Cam 1 exhaust position |
| C12 | AN03 | TPS2A |
| C13 | AN04 | Cam 2 exhaust position |
| C14 | AN05 | Cam position sensor |
| C15 | AN06 | Crank position sensor |
| C16 | AN07 | Cam 2 position sensor |
| C17 | AN08 | — |
| C18 | AN09 | MAP absolute sensor |
| C19 | AN10 | PPS1 |
| C20 | AN11 | PPS2 |
| C21 | AN12 | — |
| C22 | AN13 | Intake temperature |
| C23 | AN14 | Air charge temperature |
| C24 | AN15 | Coolant temperature |
| C25 | AN16 | Cruise control switch |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition switch |
| C29 | AN S1 / Slave An01 | Oil temperature |
| C30 | AN S2 / Slave An02 | TPS1B |
| C31 | AN S3 / Slave An03 | TPS2B |
| C32 | AN S4 / Slave An04 | Brake switch |
| C33 | AN S5 / Slave An05 | — |
| C34 | AN S6 / Slave An06 | — |
The HR section repeats lambda-1 software labels in the second-lambda rows; verify wiring and assigned sensor type with Syvecs. Follow the source diagram and the exact kit configuration for sensor polarity, current limits and solder-bridge settings.