| 101 | Injector No. 1 cylinder drive signal | Injector Output 2 | Injectors for Cylinders 1 and 4 are paired |
| 102 | NC | - | - |
| 103 | Injector No. 3 cylinder drive signal | Injector Output 3 | Injectors for Cylinders 3 and 5 are paired |
| 104 | Variable air intake control solenoid valve control signal [RB25DE (L/B), RB25DE] Turbo pressure control solenoid valve controls [RB25DET] | Aux Output 2 | — |
| 105 | Injector No. 2 cylinder drive signal | Injector Output 1 | Injectors for Cylinders 2 and 6 are paired |
| 106* | Line pressure solenoid valve control signal | - | - |
| 107 | Air jet swirl control solenoid valve control signal [ RB20DE (L/B)] | - | - |
| 108 | Canister purge control valve control signal | - | - |
| 109 | Control unit power supply (Counter- electromotive current feedback circuit) | Const 12V | Straight from battery via fuse |
| 110 | Injector No. 5 cylinder drive signal | Injector Output 3 | Injectors for Cylinders 3 and 5 are paired |
| 111 | Fuel pump terminal voltage control output signal [RB25DET] | +5V output | Connected to TPS5V via R9 (0R) or to SGND by populating R11 with 0R |
| 112 | Injector No. 6 cylinder drive signal | Injector Output 1 | Injectors for Cylinders 2 and 6 are paired |
| 113* | Line pressure solenoid valve control signal (Dropping resistor circuit) | - | - |
| 114 | Injector No. 4 cylinder drive signal | Injector Output 2 | Injectors for Cylinders 1 and 4 are paired |
| 116 | Injector ground | Power Ground | — |
| 117 | Variable timing control solenoid valve control signal | Aux Output 3 | — |
| 118 | Heated oxygen sensor heater control signal | Power Ground | Connected straight to ground |
| 119* | Power indicator lamp | - | - |
| 120* | Lockup solenoid valve control signal | - | - |
| 121* | Shift solenoid valve A control signal | - | - |
| 122* | Shift solenoid valve B control signal | - | - |
| 123 | NC | - | - |
| 124 | Injector ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | Plugs for Cylinders 1 and 6 are fired together in wasted spark |
| 2 | To Igniter for Cylinder 5 | Ignition output 2 | Plugs for Cylinders 2 and 5 are fired together in wasted spark |
| 3 | To Igniter for Cylinder 3 | Ignition output 3 | Plugs for Cylinders 3 and 4 are fired together in wasted spark |
| 4 | ECM & IGN Coil Relay Control Signal | — | When pin 24 has 12V, this pin is pulled low to activate the ECM & IGN coil relay |
| 5 | Tacho out | Aux Output 6 | — |
| 6 | NC | - | - |
| 7 | To Igniter for Cylinder 6 | Ignition output 1 | Plugs for Cylinders 1 and 6 are fired together in wasted spark |
| 8 | To Igniter for Cylinder 2 | Ignition output 2 | Plugs for Cylinders 2 and 5 are fired together in wasted spark |
| 9 | To Igniter for Cylinder 4 | Ignition output 3 | Plugs for Cylinders 3 and 4 are fired together in wasted spark |
| 10 | NC | - | - |
| 11 | AAC valve control signal | Aux Output 1 | — |
| 12 | NC | - | - |
| 13 | Fuel pump relay | Aux Output 5 | — |
| 14 | Air conditioner control signal | Aux Output 4 | — |
| 15 | NC | - | - |
| 16 | NC | - | - |
| 17 | Malfunction indicator lamp | Aux Output 7 | The Adaptronic leaves this off at all times by default, but this can be changed |
| 18 | NC | - | - |
| 19 | NC | - | - |
| 20 | Ignition switch (START) signal | - | - |
| 21 | Air conditioner switch signal | Digital Input 2 | - |
| 22 | Check (Diagnosis Start) | - | - |
| 23 | Throttle sensor output signal | TPS signal | Connected to pin 37 |
| 24 | Ignition switch (IGN) signal | +12V Ignition | When this switches to 12V, the ECM & IGN coil relay is activated (see pin 4) |
| 25 | Control Unit Ground | Power Ground | — |
| 26 | Power steering oil pressure switch signal | Digital Input 1 | — |
| 27 | NC | - | - |
| 28 | SB (select bit) 1 signal | - | - |
| 29 | Vehicle speed sensor signal (Vehicle speed sensor 2) | MVSS1 | — |
| 30 | Headlamp switch signal | Digital Input 3 | — |
| 31 | Ignition power supply | - | - |
| 32 | Control Unit Ground | Power Ground | — |
| 33* | Idle position switch signal | - | - |
| 34* | "1" position switch signal | - | - |
| 35* | "2" position switch signal | - | - |
| 36 | NC | - | - |
| 37 | Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET] | TPS output signal | Connected to pin 23 |
| 38* | "0" position switch signal | - | - |
| 39 | Neutral signal (Park/neutral position signal) | Digital Input 5 | — |
| 40* | "R" position switch signal | - | - |
| 41* | Full switch signal | - | - |
| 42 | NC | - | - |
| 43 | Sensor ground | Sensor Ground | — |
| 44 | Crankshaft position sensor 120 deg (REF) signal | CAS 2 input | Connected to pin 45 |
| 45 | Crankshaft position sensor 120 deg (REF) signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 46 | Crankshaft position sensor 1 deg (POS) signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 47 | Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET] | MAP signal input | Turbo pressure is connected to the external MAP sensor input (can be disconnected by removing R8) |
| 48 | Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor | +5V output | +5V power supply for sensors |
| 49 | Rear defogger switch signal | Digital Input 4 | — |
| 50 | Heated oxygen sensor signal | O2/EGO signal input | For the GTR, this is the front O2/EGO sensor |
| 51 | Throttle motor sensor signal [RB25DET] | - | - |
| 52 | SB (select bit) 2 signal [RB25DET A/T] | - | - |
| 53 | Motor throttle switch signal [RB25DET] | - | - |
| 54 | Mass airflow sensor signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor, populate R10 with 0R (not populated by default) |
| 55 | Mass airflow sensor ground | Sensor Ground | — |
| 56 | Engine coolant temperature sensor signal | ECT signal input | — |
| 57 | Refrigerant pressure sensor signal | Spare | — |
| 58* | Output shaft rotation sensor signal (Vehicle speed sensor 1) | - | - |
| 59 | Turbine sensor signal [RB25DET A/T] | - | - |
| 60 | Oil temperature sensor signal | - | - |
| 61 | NC | - | - |
| 62 | Knock sensor signal 1 | Knock input | Both knock sensors are connected to the one knock input |
| 63 | Knock sensor signal 2 | Knock input | Both knock sensors are connected to the one knock input |
| 64 | A/T mode switch signal (POWER) [RB20DE (L/B) A/T] | - | - |
| 65 | DB (data bush 1 signal [RB25DET A/T] | - | - |
| 66 | DB (data bush 3 signal [RB25DET A/T] | - | - |
| 67 | Control unit power supply | - | - |
| 68* | O/D Off indicator lamp | - | - |
| 69 | DB (data bush 2 signal [RB25DET A/T] | - | - |
| 70 | A/T mode switch signal (SNOW) [RB20DE (L/B) A/T] | - | - |
| 71* | Stop lamp switch signal | - | - |
| 72 | Control unit power | - | - |
| 73 | NC | - | - |
| 74 | NC | - | - |
| 75 | Receive (Data input to control unit) | CAS 3 | CAS 3 for flex fuel sensor input |
| 76 | Transmit (Data output to control unit) | MAT | Air temperature sensor input |
| 77 | NC | - | - |
| 78 | Auxiliary electric fan relay control signal [RB25DE, RB25DET] | Aux Output 8 | — |
| 79 | ECM TCM, TCS/ABS integrated control signal ] Multiple communication] [RB25DE A/T, RB25DET | - | - |
| 80 | Battery power supply | - | - |