
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V2 S7D, with product code S7D-RS8V2DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Syvecs' product page links an 8Y2 guide despite this kit being labelled 8V2. Its manuals index lists a distinct 8V2 S7D guide, linked here. Verify the applicable document with the manufacturer.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V2 S7D installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Audi TTRS RS3 Mk3 8V2 S7D product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
RS3 8V2 S7D ECU and accessory connector schedules
The Syvecs RS3 8V S7D kit manual gives these ECU connector and accessory connector positions. They are not the vehicle's OEM harness cavity numbers. Check the actual kit, hardware, connector view and electrical ratings in the manual.
Source ambiguity: the source repeats lambda 1 names in several lambda 2 rows and identifies both ignition 4 and ignition 5 as N292. The rows below reproduce the manual's wording; seek Syvecs confirmation for the exact unit rather than assuming a correction.
A connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| A1 | PWR CTR OUT | Main relay output |
| A2 | H-Bridge1 | DBW + |
| A3 | H-Bridge2 | DBW − |
| A4 | H-Bridge3 | Wastegate solenoid |
| A5 | H-Bridge4 | Evap |
| A6 | H-Bridge5 | Spare output |
| A7 | H-Bridge6 | Starter relay |
| A8 | H-Bridge7 | Intake manifold flap N316 |
| A9 | H-Bridge8 | Coolant switch pump |
| A10 | GDI LS1 | Spare output |
| A11 | GDI LS2 | Injector 4− |
| A12 | GDI LS3 | Port injector 1 N532 |
| A13 | GDI LS4 | Injector 2− |
| A14 | GDI LS5 | Port injector 2 N533 |
| A15 | GDI LS6 | Injector 5− |
| A16 | GDI LS7 | Port injector 3 N534 |
| A17 | GDI LS8 | Injector 3− |
| A18 | GDI HS1/2 | Injector 4+ |
| A19 | GDI HS3/4 | Injector 2+ |
| A20 | GDI Pump 1 HS | GDI pump high side |
| A21 | GDI HS5/6 | Injector 5+ |
| A22 | GDI HS7/8 | Injector 3+ |
| A23 | GDI Pump 2 HS | Injector 1+ |
| A24 | GDI Pump 1 LowSide | GDI pump low side |
| A25 | GDI Pump 2 LowSide / Injector LS | Injector 1− |
| A26 | IGN1 | Ignition 1 N70 |
| A27 | IGN2 | Ignition 2 N127 |
| A28 | IGN3 | Ignition 3 N291 |
| A29 | IGN4 | Ignition 4 N292 |
| A30 | IGN5 | Ignition 5 N292 (as printed) |
| A31 | IGN6 | Tacho sync |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
B connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2 L | CAN 2 |
| B3 | CAN2 H | CAN 2 |
| B4 | KNOCK 1 | Knock 1 |
| B5 | KNOCK 2 | Knock 2 |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | LamV / LamD1+ / LamLun1 |
| B9 | LAM1B | LamI / LamD1− / LamIP1 |
| B10 | LAM1C | LamLIA1 |
| B11 | LAM1D | LamGND / LamLVM1 |
| B12 | LAM1HEATER | Lambda heater |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | LamV / LamD1+ / LamLun1 |
| B15 | LAM2B | LamI / LamD1− / LamIP1 |
| B16 | LAM2C | LamLIA1 |
| B17 | LAM2D | LamGND / LamLVM1 |
| B18 | LAM2HEATER | Lambda heater |
| B19 | IVBAT | 12 V |
| B20 | KLINE | K-line |
| B21 | RS232RX | RS232 RX |
| B22 | RS232TX | RS232 TX |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
C connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| C1 | KNOCKGND | Knock ground; OEM: Knock − |
| C2 | ANGND | Sensor ground; OEM: Tested |
| C3 | ANGND | Sensor ground; OEM: Tested |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | 5 V output; OEM: Tested |
| C6 | 5V OUT | 5 V output; OEM: Tested |
| C7 | 5V OUT | 5 V output |
| C8 | CAN1 L | CAN 1 low; OEM: Powertrain CAN |
| C9 | CAN1 H | CAN 1 high; OEM: Powertrain CAN |
| C10 | AN01 | Bipolar input; OEM: Start request |
| C11 | AN02 | Bipolar input; OEM: DI pressure |
| C12 | AN03 | Bipolar input |
| C13 | AN04 | Bipolar input |
| C14 | AN05 | Unipolar input; OEM: VVT1 intake position |
| C15 | AN06 | Unipolar input; OEM: VVT1 exhaust position |
| C16 | AN07 | Unipolar input; OEM: Crank sensor |
| C17 | AN08 | Unipolar input; OEM: Brake light switch |
| C18 | AN09 | Voltage input; OEM: TPS1A |
| C19 | AN10 | Voltage input; OEM: TPS1B |
| C20 | AN11 | Voltage input; OEM: PPSA |
| C21 | AN12 | Voltage input; OEM: PPSB |
| C22 | AN13 | Resistive input; OEM: Coolant temperature G62 |
| C23 | AN14 | Resistive input; OEM: Intake air temperature |
| C24 | AN15 | Resistive input; OEM: EGT1 |
| C25 | AN16 | Resistive input; OEM: EGT2 |
| C26 | EGT1− | EGT 1 negative; OEM: EGT1− |
| C27 | EGT1+ | EGT 1 positive; OEM: EGT1+ |
| C28 | PWR CTR IN | Main relay input switch; OEM: Key-on signal 15 |
| C29 | AN S1 | Unipolar input; OEM: Intake position flap |
| C30 | AN S2 | Unipolar input; OEM: Low-side fuel pressure |
| C31 | AN S3 | Unipolar input; OEM: SENT MAP |
| C32 | AN S4 | Unipolar input; OEM: SENT ACT |
| C33 | AN S5 | Unipolar input; OEM: Pre-throttle MAP |
| C34 | AN S6 | Unipolar input; OEM: Intermediate shaft speed |
D connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| D1 | DVBAT1 | GDI power supply |
| D2 | DVBAT2 | GDI power supply |
| D3 | DVBAT3 | GDI power supply |
| D4 | DVBAT4 | GDI power supply |
| D5 | FUEL9 | PWM / fuel output; OEM: Port injector 4 N535 |
| D6 | FUEL10 | PWM / fuel output; OEM: Port injector 5 N536 |
| D7 | FUEL11 | PWM / fuel output; OEM: Fuel pump PWM |
| D8 | FUEL12 | PWM / fuel output; OEM: Cooling fan PWM |
| D9 | FUEL13 | PWM / fuel output; OEM: Turbo recirculation N249 |
| D10 | FUEL14 | PWM / fuel output; OEM: Exhaust cam solenoids A |
| D11 | LSO1 | PWM output; OEM: VVT1 intake N205 |
| D12 | LSO2 | PWM output; OEM: VVT1 exhaust N316 |
| D13 | LSO3 | PWM output; OEM: Oil pressure valve |
| D14 | LSO4 | PWM output; OEM: Crankcase breather |
| D15 | LSO5 | PWM output; OEM: Coolant shut-off valve |
| D16 | LSO6 | PWM output; OEM: Coolant pump PWM |
| D17 | EGT2− | EGT 2 negative |
| D18 | EGT2+ | EGT 2 positive |
| D19 | NC | NC in source |
| D20 | NC | NC in source |
| D21 | NC | NC in source |
| D22 | NC | NC in source |
| D23 | CAN3L | CAN 3 low |
| D24 | CAN3H | CAN 3 high |
| D25 | PWRGND | Power ground |
| D26 | PWRGND | Power ground |
Accessory connector
| Terminal | Syvecs label | Function / OEM note in source |
|---|---|---|
| B1 | GND | Ground |
| B2 | Fuel1 | Spare output |
| B3 | LSO3 | Spare output - Slave1 Out13 |
| B4 | LSO4 | Spare output - Slave1 Out14 |
| B5 | LSO5 | Spare output - Slave1 Out15 |
| B6 | LSO6 | Spare output - Slave1 Out16 |
| B7 | 12 V | |
| B8 | H-Bridge 5 | Spare output - Slave1 Out5 |
| B9 | CAN2L | Spare CAN |
| B10 | CAN2H | Spare CAN |
| B11 | RS232RX | |
| B12 | RS232TX | |
| B13 | LAM2A | Spare input - S1AN08 |
| B14 | EGT1− | K-type EGT |
| B15 | EGT1+ | K-type EGT |
| B16 | AN03 | Spare input - bipolar |
| B17 | AN04 | Spare input - bipolar |
| B18 | AN15 | Spare input |
| B19 | AN16 | Spare input |
| B20 | S1AN4 | Spare input if non-SENT MAP is used |
| B21 | ANGround | Sensor ground |
| B22 | 5V Out | 5 V output for sensors |
| B23 | Cat5 pin 2 | Ethernet |
| B24 | Cat5 pin 1 | Ethernet |
| B25 | Cat5 pin 6 | Ethernet |
| B26 | Cat5 pin 3 | Ethernet |