Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Syvecs Nissan R35 GTR 2009-2019 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index

R35 kit ECU connector schedules

The Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.

Connector A — 34 way

PinSyvecs I/OKit function / source noteA1PWR CTR OUTThrottle and main relayA2H-Bridge1 / SlaveOut1DBWA3H-Bridge2 / SlaveOut2DBWA4H-Bridge3 / SlaveOut3DBWA5H-Bridge4 / SlaveOut4DBWA6H-Bridge5 / SlaveOut5Boost solenoidA7H-Bridge6 / SlaveOut6Fuel pump 2A8H-Bridge7 / SlaveOut7EvapA9H-Bridge8 / SlaveOut8—A10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Primary injector 5A15FUEL6Primary injector 6A16FUEL7Secondary injector 1 or spareA17FUEL8Secondary injector 2 or spareA18PWM1 / *FUEL9Secondary injector 3 or spareA19PWM2 / *FUEL10Secondary injector 4 or spareA20PWM3 / *FUEL11Fuel pump controller – 5 V pull-upA21PWM4 / *FUEL12Secondary injector 5 or spareA22PWM5Secondary injector 6 or spareA23PWM6TachoA24PWM7VVT1A25PWM8VVT2A26IGN1Ignition 1A27IGN2Ignition 2A28IGN3Ignition 3A29IGN4Ignition 4A30IGN5Ignition 5A31IGN6Ignition 6A32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source noteB1PWRGNDPower groundB2CAN2L—B3CAN2H—B4KNOCK—B5KNOCK 2—B6PVBATConstant 12 VB7IVBAT12 VB8LAM1A2.2 V per sourceB9LAM1B—B10LAM1C—B11LAM1D—B12LAM1HEATERLambda heaterB13IVBAT12 VB14LAM2A2.2 V per sourceB15LAM2B1.8 V per sourceB16LAM2C—B17LAM2D—B18LAM2HEATERLambda heaterB19IVBAT12 VB20KLINE—B21RS232RX—B22RS232TX—B23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source noteC1KNOCKGND—C2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT—C65V OUT—C75V OUT—C8CAN L—C9CAN H—C10AN01TPS1AC11AN02TPS1BC12AN03TPS2AC13AN04TPS2BC14AN05Cam position sensorC15AN06Crank position sensorC16AN07Cam 2 position sensorC17AN08Oil temperatureC18AN09MAP absolute sensorC19AN10PPS1C20AN11PPS2C21AN12Brake switchC22AN13Fuel temperatureC23AN14Air charge temperatureC24AN15Coolant temperatureC25AN16Cruise control switchC26EGT1−—C27EGT1+—C28PWR CTR INIgnition switchC29AN S1 / Slave An01Secondary air injection (flex fuel)C30AN S2 / Slave An02MAF1 / spare inputC31AN S3 / Slave An03MAF2 / spare inputC32AN S4 / Slave An04—C33AN S5 / Slave An05Pre-throttle MAP1 / spare inputC34AN S6 / Slave An06Pre-throttle MAP2 / spare input

The source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs Nissan R35 GTR 2009-2019 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

R35 kit ECU connector schedules

The Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTThrottle and main relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3DBW
A5H-Bridge4 / SlaveOut4DBW
A6H-Bridge5 / SlaveOut5Boost solenoid
A7H-Bridge6 / SlaveOut6Fuel pump 2
A8H-Bridge7 / SlaveOut7Evap
A9H-Bridge8 / SlaveOut8—
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Primary injector 6
A16FUEL7Secondary injector 1 or spare
A17FUEL8Secondary injector 2 or spare
A18PWM1 / *FUEL9Secondary injector 3 or spare
A19PWM2 / *FUEL10Secondary injector 4 or spare
A20PWM3 / *FUEL11Fuel pump controller – 5 V pull-up
A21PWM4 / *FUEL12Secondary injector 5 or spare
A22PWM5Secondary injector 6 or spare
A23PWM6Tacho
A24PWM7VVT1
A25PWM8VVT2
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCK—
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1A2.2 V per source
B9LAM1B—
B10LAM1C—
B11LAM1D—
B12LAM1HEATERLambda heater
B13IVBAT12 V
B14LAM2A2.2 V per source
B15LAM2B1.8 V per source
B16LAM2C—
B17LAM2D—
B18LAM2HEATERLambda heater
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCKGND—
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01TPS1A
C11AN02TPS1B
C12AN03TPS2A
C13AN04TPS2B
C14AN05Cam position sensor
C15AN06Crank position sensor
C16AN07Cam 2 position sensor
C17AN08Oil temperature
C18AN09MAP absolute sensor
C19AN10PPS1
C20AN11PPS2
C21AN12Brake switch
C22AN13Fuel temperature
C23AN14Air charge temperature
C24AN15Coolant temperature
C25AN16Cruise control switch
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01Secondary air injection (flex fuel)
C30AN S2 / Slave An02MAF1 / spare input
C31AN S3 / Slave An03MAF2 / spare input
C32AN S4 / Slave An04—
C33AN S5 / Slave An05Pre-throttle MAP1 / spare input
C34AN S6 / Slave An06Pre-throttle MAP2 / spare input

The source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.

Revision 2: Syvecs Nissan R35 GTR 2009-2019 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan R35 GTR 2009-2019 S7Plus, with product code S7Plus-NGTR. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Nissan R35 GTR 2009-2019 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

R35 kit ECU connector schedules

The Syvecs R35GTR kit manual, pages 10–12, documents the S7Plus ECU connector assignments below. These are ECU pins, not the original Nissan harness pinout. The manufacturer states the 2020-onward kit uses a different vehicle connector; verify the precise adapter and model year before using these assignments.

Connector A — 34 way

PinSyvecs I/OKit function / source note
A1PWR CTR OUTThrottle and main relay
A2H-Bridge1 / SlaveOut1DBW
A3H-Bridge2 / SlaveOut2DBW
A4H-Bridge3 / SlaveOut3DBW
A5H-Bridge4 / SlaveOut4DBW
A6H-Bridge5 / SlaveOut5Boost solenoid
A7H-Bridge6 / SlaveOut6Fuel pump 2
A8H-Bridge7 / SlaveOut7Evap
A9H-Bridge8 / SlaveOut8—
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Primary injector 5
A15FUEL6Primary injector 6
A16FUEL7Secondary injector 1 or spare
A17FUEL8Secondary injector 2 or spare
A18PWM1 / *FUEL9Secondary injector 3 or spare
A19PWM2 / *FUEL10Secondary injector 4 or spare
A20PWM3 / *FUEL11Fuel pump controller – 5 V pull-up
A21PWM4 / *FUEL12Secondary injector 5 or spare
A22PWM5Secondary injector 6 or spare
A23PWM6Tacho
A24PWM7VVT1
A25PWM8VVT2
A26IGN1Ignition 1
A27IGN2Ignition 2
A28IGN3Ignition 3
A29IGN4Ignition 4
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

Connector B — 26 way

PinSyvecs I/OKit function / source note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCK—
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V
B8LAM1A2.2 V per source
B9LAM1B—
B10LAM1C—
B11LAM1D—
B12LAM1HEATERLambda heater
B13IVBAT12 V
B14LAM2A2.2 V per source
B15LAM2B1.8 V per source
B16LAM2C—
B17LAM2D—
B18LAM2HEATERLambda heater
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

Connector C — 34 way

PinSyvecs I/OKit function / source note
C1KNOCKGND—
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN L—
C9CAN H—
C10AN01TPS1A
C11AN02TPS1B
C12AN03TPS2A
C13AN04TPS2B
C14AN05Cam position sensor
C15AN06Crank position sensor
C16AN07Cam 2 position sensor
C17AN08Oil temperature
C18AN09MAP absolute sensor
C19AN10PPS1
C20AN11PPS2
C21AN12Brake switch
C22AN13Fuel temperature
C23AN14Air charge temperature
C24AN15Coolant temperature
C25AN16Cruise control switch
C26EGT1−—
C27EGT1+—
C28PWR CTR INIgnition switch
C29AN S1 / Slave An01Secondary air injection (flex fuel)
C30AN S2 / Slave An02MAF1 / spare input
C31AN S3 / Slave An03MAF2 / spare input
C32AN S4 / Slave An04—
C33AN S5 / Slave An05Pre-throttle MAP1 / spare input
C34AN S6 / Slave An06Pre-throttle MAP2 / spare input

The source repeats lambda-1 software labels for the LAM2A–D section. Confirm the second lambda channel with Syvecs rather than assuming the wiring is identical.