
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as McLaren 570, with product code S7Plus-M838T-570. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs McLaren 570 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs McLaren 570 product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
M838T kit ECU connector schedules
From Syvecs M838T kit manual, version 1.2, pages 5–7, which lists MP4-12C, 570 and 650S. These are the S7Plus ECU's three connectors, not the original vehicle loom pins. Match the adapter, configuration, source connector view and electrical limits to the actual car.
Connector A — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| A1 | PWR CTR OUT | Main relay |
| A2 | H-Bridge1 / SlaveOut1 | DBW1 |
| A3 | H-Bridge2 / SlaveOut2 | DBW1 |
| A4 | H-Bridge3 / SlaveOut3 | DBW2 |
| A5 | H-Bridge4 / SlaveOut4 | DBW2 |
| A6 | H-Bridge5 / SlaveOut5 | Thermostat ×2 |
| A7 | H-Bridge6 / SlaveOut6 | Starter low side |
| A8 | H-Bridge7 / SlaveOut7 | Wastegate 1 |
| A9 | H-Bridge8 / SlaveOut8 | Wastegate 2 |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Primary injector 5 |
| A15 | FUEL6 | Primary injector 6 |
| A16 | FUEL7 | Primary injector 7 |
| A17 | FUEL8 | Primary injector 8 |
| A18 | FUEL9 | — |
| A19 | FUEL10 | Fuel pump ×2 |
| A20 | FUEL11 | Evap |
| A21 | FUEL12 | Dump valve ×2 |
| A22 | FUEL13 | VVT1 intake |
| A23 | FUEL14 | VVT2 intake |
| A24 | FUEL15 | VVT1 exhaust |
| A25 | FUEL16 | VVT2 exhaust |
| A26 | IGN1 | IGN1 & 4 |
| A27 | IGN2 | IGN5 & 8 |
| A28 | IGN3 | IGN2 & 3 |
| A29 | IGN4 | IGN6 & 7 |
| A30 | IGN5 | Radiator fan 1 |
| A31 | IGN6 | Radiator fan 2 |
| A32 | PWRGND | Intake sound generator ground |
| A33 | PWRGND | Ground |
| A34 | PWRGND | Ground |
Connector B — 26 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN 2L | CAN 2 |
| B3 | CAN 2H | CAN 2 |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V |
| B8 | LAM1A | LSU 4.9 connector pin 6 |
| B9 | LAM1B | LSU 4.9 connector pin 1 |
| B10 | LAM1C | LSU 4.9 connector pin 5 |
| B11 | LAM1D | LSU 4.9 connector pin 2 |
| B12 | LAM1HEATER | LSU 4.9 connector pin 3 |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | Source repeats LSU 4.9 pin 6; confirm with Syvecs |
| B15 | LAM2B | Source repeats LSU 4.9 pin 1; confirm with Syvecs |
| B16 | LAM2C | Source repeats LSU 4.9 pin 5; confirm with Syvecs |
| B17 | LAM2D | Source repeats LSU 4.9 pin 2; confirm with Syvecs |
| B18 | LAM2HEATER | Source repeats LSU 4.9 pin 3; confirm with Syvecs |
| B19 | IVBAT | 12 V; starter relay high side |
| B20 | KLINE | Alternator LIN |
| B21 | RS232RX | Source says set as CAN L for throttle body with CAN bridge |
| B22 | RS232TX | Source says set as CAN H for throttle body with CAN bridge |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
Connector C — 34 way
| Pin | Syvecs I/O | Kit function / source note |
|---|---|---|
| C1 | KNOCKGND | Knock ground |
| C2 | ANGND | B sensor grounds |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | B 5 V |
| C6 | 5V OUT | A 5 V |
| C7 | 5V OUT | — |
| C8 | CAN L | — |
| C9 | CAN H | — |
| C10 | AN01 | Crank sensor |
| C11 | AN02 | VVT1 intake |
| C12 | AN03 | VVT2 intake |
| C13 | AN04 | VVT1 exhaust |
| C14 | AN05 | VVT2 exhaust |
| C15 | AN06 | MAP manifold |
| C16 | AN07 | TPS2A |
| C17 | AN08 | TPS2B |
| C18 | AN09 | PPS1 |
| C19 | AN10 | PPS2 |
| C20 | AN11 | TPS1A |
| C21 | AN12 | TPS1B |
| C22 | AN13 | ACT1 |
| C23 | AN14 | Park neutral switch |
| C24 | AN15 | Coolant temperature |
| C25 | AN16 | Intake sound signal |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | 12 V ignition |
| C29 | AN S1 / Slave An01 | Fuel pressure |
| C30 | AN S2 / Slave An02 | Fuel temperature |
| C31 | AN S3 / Slave An03 | — |
| C32 | AN S4 / Slave An04 | Oil pressure switch |
| C33 | AN S5 / Slave An05 | MAP1 |
| C34 | AN S6 / Slave An06 | MAP2 |
The manual repeats lambda-1 software labels and LSU pin numbers for the LAM2A–D section. Confirm second-sensor wiring with Syvecs. The manufacturer does not publish the OEM car connector pinout in this schedule.