Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- DTAFast standalone engine management
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 3
Removed text is struck through; added text is highlighted.
DTAFast E4 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA four-cylinder power schematic shows two ignition coil outputs, injector output, switched supply and separate battery earth connections.
Identification
Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.
Model-specific pinout and wiring
The manufacturer E4 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.
Power connector assignments in the 1997 drawing
The following positions are traced from the DTAFast E4 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.
PinFunction shownAIgnition-switched supplyBBattery negative / groundCBattery negative / groundDCoil 1, earth sideECoil 2, earth sideFInjector bank 1GNot shown in this power schematicHNot shown in this power schematicJNot shown in this power schematicKGear-change light, 20 W maximumLNot shown in this power schematicMNot shown in this power schematicNTachometer outputPNot shown in this power schematicRNot shown in this power schematicSNot shown in this power schematicTNot shown in this power schematicUNot shown in this power schematic
Separate sensor connector
The DTAFast E4/E6/E8 sensor schematic dated 14 February 1997 depicts a separate male connector on the loom. The table follows the terminal connections drawn for the listed sensor examples, not the separate female power connector. “No connected function shown” is not a claim that the cavity is unused in every ECU. Use the source’s connector view and check the exact sensor and loom.Sensor connector pinConnection in the DTAFast drawingAShift-cut switch terminal 2BShift-cut switch terminal 1CThrottle potentiometer high side (throttle open)DThrottle potentiometer wiperEThrottle potentiometer opposite endFWater-temperature sensor terminal 1GWater-temperature sensor terminal 2HAir-temperature sensor terminal 1JAir-temperature sensor terminal 2KPressure sensor terminal 3, 5 V in the Marelli exampleLPressure sensor terminal 1, signal in the Marelli exampleMCrank sensor terminal 1 in the depicted Ford/Vauxhall exampleNCrank sensor terminal 2 / shield return in the Vauxhall examplePLambda sensor terminal 2 in the diagramRLambda sensor terminal 1 / earthed sideSNo connected function shownTNo connected function shownUNo connected function shownVPressure sensor terminal 2, earth in the Marelli exampleThe schematic says to use screened crank-sensor cable, with the Vauxhall sensor pin 1 to M, pin 2 to N and pin 3 shield to N. It calls for reversed Ford/Marelli crank sensor polarity and states that R connects to the earthed side of the lambda sensor. Confirm sensor terminals and electrical configuration in the original diagram.The source draws a separate male loom sensor connector. Its E4/E6/E8 sensor diagram specifies, among other connections, M and N for the Vauxhall crank sensor, with sensor pin 1 to M and pin 2 to N; screened cable shields join N. The guide says the Marelli sensor polarity differs from Ford. R goes to the earthed side of the lambda sensor. Obtain the exact diagram and connector view for all other sensor cavities; this power-connector table is not a complete sensor pinout.Related documentation
DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: DTAFast E4
DTAFast E4 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA four-cylinder power schematic shows two ignition coil outputs, injector output, switched supply and separate battery earth connections.
Identification
Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.
Model-specific pinout and wiring
The manufacturer E4 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.
Power connector assignments in the 1997 drawing
The following positions are traced from the DTAFast E4 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.
| Pin | Function shown |
|---|
| A | Ignition-switched supply |
| B | Battery negative / ground |
| C | Battery negative / ground |
| D | Coil 1, earth side |
| E | Coil 2, earth side |
| F | Injector bank 1 |
| G | Not shown in this power schematic |
| H | Not shown in this power schematic |
| J | Not shown in this power schematic |
| K | Gear-change light, 20 W maximum |
| L | Not shown in this power schematic |
| M | Not shown in this power schematic |
| N | Tachometer output |
| P | Not shown in this power schematic |
| R | Not shown in this power schematic |
| S | Not shown in this power schematic |
| T | Not shown in this power schematic |
| U | Not shown in this power schematic |
Separate sensor connector
The source draws a separate male loom sensor connector. Its E4/E6/E8 sensor diagram specifies, among other connections, M and N for the Vauxhall crank sensor, with sensor pin 1 to M and pin 2 to N; screened cable shields join N. The guide says the Marelli sensor polarity differs from Ford. R goes to the earthed side of the lambda sensor. Obtain the exact diagram and connector view for all other sensor cavities; this power-connector table is not a complete sensor pinout.
Related documentation
DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.
Revision 3: DTAFast E4
DTAFast E4 is a historic programmable engine-management identity documented in the manufacturer's model wiring schematic. The 14 February 1997 DTA four-cylinder power schematic shows two ignition coil outputs, injector output, switched supply and separate battery earth connections.
Identification
Identify the actual case label, harness connectors, output configuration and firmware. An old loom may have been modified for a particular engine. No current product availability or universal support status is inferred from this historical schematic.
Model-specific pinout and wiring
The manufacturer E4 drawing supplies connector views, functions, sensor/actuator examples and grounding. The separate E4/E6/E8 sensor schematic must be used alongside the power schematic. Both battery earth connections are called out in the period power drawing. Match connectors and diagram orientation to the actual ECU; do not transfer pin assignments from another E- or S-series model.
Power connector assignments in the 1997 drawing
The following positions are traced from the DTAFast E4 power schematic dated 14 February 1997, which labels the view as the female loom power connector. “Not shown” means the drawing does not identify a connection; it does not establish that a cavity is unused in every build. Connect both specified power grounds and use the manufacturer diagram and correct fuses and relay arrangements.
| Pin | Function shown |
|---|
| A | Ignition-switched supply |
| B | Battery negative / ground |
| C | Battery negative / ground |
| D | Coil 1, earth side |
| E | Coil 2, earth side |
| F | Injector bank 1 |
| G | Not shown in this power schematic |
| H | Not shown in this power schematic |
| J | Not shown in this power schematic |
| K | Gear-change light, 20 W maximum |
| L | Not shown in this power schematic |
| M | Not shown in this power schematic |
| N | Tachometer output |
| P | Not shown in this power schematic |
| R | Not shown in this power schematic |
| S | Not shown in this power schematic |
| T | Not shown in this power schematic |
| U | Not shown in this power schematic |
Separate sensor connector
The DTAFast E4/E6/E8 sensor schematic dated 14 February 1997 depicts a separate male connector on the loom. The table follows the terminal connections drawn for the listed sensor examples, not the separate female power connector. “No connected function shown” is not a claim that the cavity is unused in every ECU. Use the source’s connector view and check the exact sensor and loom.
| Sensor connector pin | Connection in the DTAFast drawing |
|---|
| A | Shift-cut switch terminal 2 |
| B | Shift-cut switch terminal 1 |
| C | Throttle potentiometer high side (throttle open) |
| D | Throttle potentiometer wiper |
| E | Throttle potentiometer opposite end |
| F | Water-temperature sensor terminal 1 |
| G | Water-temperature sensor terminal 2 |
| H | Air-temperature sensor terminal 1 |
| J | Air-temperature sensor terminal 2 |
| K | Pressure sensor terminal 3, 5 V in the Marelli example |
| L | Pressure sensor terminal 1, signal in the Marelli example |
| M | Crank sensor terminal 1 in the depicted Ford/Vauxhall example |
| N | Crank sensor terminal 2 / shield return in the Vauxhall example |
| P | Lambda sensor terminal 2 in the diagram |
| R | Lambda sensor terminal 1 / earthed side |
| S | No connected function shown |
| T | No connected function shown |
| U | No connected function shown |
| V | Pressure sensor terminal 2, earth in the Marelli example |
The schematic says to use screened crank-sensor cable, with the Vauxhall sensor pin 1 to M, pin 2 to N and pin 3 shield to N. It calls for reversed Ford/Marelli crank sensor polarity and states that R connects to the earthed side of the lambda sensor. Confirm sensor terminals and electrical configuration in the original diagram.
Related documentation
DTAFast's wiring archive includes crank sensor rules and legacy ECU sheets. Confirm support, software and hardware serviceability directly with DTAFast. See the DTAFast family overview.