Page organisation in this revision
- Page type
- Technical article
- Subject
- Gearboxes
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Volkswagen
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
The Volkswagen Group 0CT is a five-speed automated manual gearbox based on the 0CF manual, with an electronically controlled single dry clutch and electromechanical actuators. It is not the two-clutch DSG design. Volkswagen's 2015 UK up! brochure describes its ASG as a single-clutch gearbox with automatic or driver-requested shifts and a brief interruption of driving torque during a change. Check the actual gearbox code, vehicle, market and controller before applying this guide; an ASG badge alone does not establish the same hardware on all cars. Volkswagen up! brochure; Volkswagen training SSP 512, pp. 2–5 (French).
What the controller operates
In the 0CT training example, control unit J514 commands clutch actuator VX64 and gear actuator VX65. Motor V530 operates the clutch; the actuator for the gearbox uses separate selection and engagement motors V528 and V529. Each motor has Hall-based rotation feedback. A gearbox input-speed sender, selector request, brake input and information from other controllers also contribute to the operating sequence. This describes the documented 0CT, not the electrohydraulic Lupo 3L 085 or the DSG. Volkswagen SSP 512, pp. 14, 24 and 28–31.
In the illustrated system, the clutch opens before gear selection and the control unit moves the selector and engagement motors using learnt geometry; it then controls clutch re-engagement. A mechanical clutch and gearbox remain present despite having no clutch pedal. An electric motor, its power/command, feedback, its linkage and the part it moves must be considered as a system; an actuator code does not by itself identify the failed component.
Symptoms and useful evidence
ObservationInvestigationLimit
No crank or N / brake indicationCompare selector request, displayed status and brake input as seen by the relevant controllers. SSP 512 describes an N and brake condition for start authorization in its example.A rejected request may be a valid interlock or a faulty input; do not bypass it. VW SSP 512, pp. 13 and 29.
Request not fulfilled or particular gear unavailableRecord requested and recognized gear, clutch state, transmission and engine faults, voltage and the selection/engagement actuator feedback the correct tool exposes.The problem can be in an input, control, actuator, wiring, clutch release or mechanical gearbox; an indication is not a parts verdict.
Intermittent no-shift or actuator feedback faultInspect supply and connectors and compare actuator commands with the related motor feedback using the exact diagnostic plan. Each motor's rotation sensors enable direction and movement to be recognized.Motor rotation does not prove correct clutch release or gear engagement. The training description is not an approved wiring test or a pinout.
Judder, slipping, or overheating warningRecord take-up or driving conditions, warning, engine/input speeds, gear and any related faults. Consider friction clutch condition and actuation as well as engine and driveline causes.The training manual distinguishes its display states; confirm the instrument's meaning and recovery action in the specific car's handbook. Do not assume every indication is a worn clutch.
Volkswagen SSP 512 shows gearbox input-speed sender G182 for its documented system. Do not infer a pin assignment, sensor definition or location on another variant from that label alone; verify the current VIN-specific wiring and diagnostic information. The sensor detects the rotating first-gear wheel to determine gearbox input speed, according to the source. Volkswagen SSP 512, p. 30.
Japan up! transmission-control recall: inaccurate position detectionJapan recall 外-2045, filed 18 June 2014 by Volkswagen Group Japan, covers identified VW up! 1.0/55 kW vehicles imported between 26 June 2012 and 17 March 2014. Volkswagen reported that an unsuitable transmission-controller programme could fail to detect gear or clutch position accurately while driving; the transmission might remain in gear or release the clutch, leaving the car coasting and potentially unable to move off after stopping. The prescribed action was to identify the controller and reprogramme it or replace it with an updated unit as applicable. The Japanese Consumer Affairs Agency notice records the same recall. Check VIN, market and campaign history with Volkswagen; this Japanese campaign is not proof that every 0CT or non-Japanese car has the same fault. A position-related symptom also has mechanical, electrical and sensor causes.Learning and service boundaries
Volkswagen describes a basic setting in which the gear actuator explores the selection and engagement paths and determines their limits. It is an active procedure that moves the mechanism, and is not a general-purpose fix for a mechanical, electrical or supply fault. Before clearing faults or running service functions, save the fault status and relevant data. Follow the current repair sequence, equipment, conditions and learning requirements for the actual repair. Volkswagen SSP 512, pp. 25–26.
That training document cautions against applying grease to the particular clutch-lever ball and socket it illustrates, because grease combined with clutch abrasion can increase wear and noise; it also states that an opened gear actuator must be replaced after removal. These are document- and component-specific instructions, not a universal rule for other systems. Use current Volkswagen workshop instructions before disassembly or lubrication. Volkswagen SSP 512, p. 32.
See Lupo 3L electrohydraulic gearbox, DQ200 dual-clutch diagnosis and the electronic gearbox guide.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Volkswagen Group 0CT ASG automated manual gearbox diagnosis
The Volkswagen Group 0CT is a five-speed automated manual gearbox based on the 0CF manual, with an electronically controlled single dry clutch and electromechanical actuators. It is not the two-clutch DSG design. Volkswagen's 2015 UK up! brochure describes its ASG as a single-clutch gearbox with automatic or driver-requested shifts and a brief interruption of driving torque during a change. Check the actual gearbox code, vehicle, market and controller before applying this guide; an ASG badge alone does not establish the same hardware on all cars. Volkswagen up! brochure; Volkswagen training SSP 512, pp. 2–5 (French).
What the controller operates
In the 0CT training example, control unit J514 commands clutch actuator VX64 and gear actuator VX65. Motor V530 operates the clutch; the actuator for the gearbox uses separate selection and engagement motors V528 and V529. Each motor has Hall-based rotation feedback. A gearbox input-speed sender, selector request, brake input and information from other controllers also contribute to the operating sequence. This describes the documented 0CT, not the electrohydraulic Lupo 3L 085 or the DSG. Volkswagen SSP 512, pp. 14, 24 and 28–31.
In the illustrated system, the clutch opens before gear selection and the control unit moves the selector and engagement motors using learnt geometry; it then controls clutch re-engagement. A mechanical clutch and gearbox remain present despite having no clutch pedal. An electric motor, its power/command, feedback, its linkage and the part it moves must be considered as a system; an actuator code does not by itself identify the failed component.
Symptoms and useful evidence
| Observation | Investigation | Limit |
| No crank or N / brake indication | Compare selector request, displayed status and brake input as seen by the relevant controllers. SSP 512 describes an N and brake condition for start authorization in its example. | A rejected request may be a valid interlock or a faulty input; do not bypass it. VW SSP 512, pp. 13 and 29. |
| Request not fulfilled or particular gear unavailable | Record requested and recognized gear, clutch state, transmission and engine faults, voltage and the selection/engagement actuator feedback the correct tool exposes. | The problem can be in an input, control, actuator, wiring, clutch release or mechanical gearbox; an indication is not a parts verdict. |
| Intermittent no-shift or actuator feedback fault | Inspect supply and connectors and compare actuator commands with the related motor feedback using the exact diagnostic plan. Each motor's rotation sensors enable direction and movement to be recognized. | Motor rotation does not prove correct clutch release or gear engagement. The training description is not an approved wiring test or a pinout. |
| Judder, slipping, or overheating warning | Record take-up or driving conditions, warning, engine/input speeds, gear and any related faults. Consider friction clutch condition and actuation as well as engine and driveline causes. | The training manual distinguishes its display states; confirm the instrument's meaning and recovery action in the specific car's handbook. Do not assume every indication is a worn clutch. |
Volkswagen SSP 512 shows gearbox input-speed sender G182 for its documented system. Do not infer a pin assignment, sensor definition or location on another variant from that label alone; verify the current VIN-specific wiring and diagnostic information. The sensor detects the rotating first-gear wheel to determine gearbox input speed, according to the source. Volkswagen SSP 512, p. 30.
Learning and service boundaries
Volkswagen describes a basic setting in which the gear actuator explores the selection and engagement paths and determines their limits. It is an active procedure that moves the mechanism, and is not a general-purpose fix for a mechanical, electrical or supply fault. Before clearing faults or running service functions, save the fault status and relevant data. Follow the current repair sequence, equipment, conditions and learning requirements for the actual repair. Volkswagen SSP 512, pp. 25–26.
That training document cautions against applying grease to the particular clutch-lever ball and socket it illustrates, because grease combined with clutch abrasion can increase wear and noise; it also states that an opened gear actuator must be replaced after removal. These are document- and component-specific instructions, not a universal rule for other systems. Use current Volkswagen workshop instructions before disassembly or lubrication. Volkswagen SSP 512, p. 32.
See Lupo 3L electrohydraulic gearbox, DQ200 dual-clutch diagnosis and the electronic gearbox guide.
Revision 2: Volkswagen Group 0CT ASG automated manual gearbox diagnosis
The Volkswagen Group 0CT is a five-speed automated manual gearbox based on the 0CF manual, with an electronically controlled single dry clutch and electromechanical actuators. It is not the two-clutch DSG design. Volkswagen's 2015 UK up! brochure describes its ASG as a single-clutch gearbox with automatic or driver-requested shifts and a brief interruption of driving torque during a change. Check the actual gearbox code, vehicle, market and controller before applying this guide; an ASG badge alone does not establish the same hardware on all cars. Volkswagen up! brochure; Volkswagen training SSP 512, pp. 2–5 (French).
What the controller operates
In the 0CT training example, control unit J514 commands clutch actuator VX64 and gear actuator VX65. Motor V530 operates the clutch; the actuator for the gearbox uses separate selection and engagement motors V528 and V529. Each motor has Hall-based rotation feedback. A gearbox input-speed sender, selector request, brake input and information from other controllers also contribute to the operating sequence. This describes the documented 0CT, not the electrohydraulic Lupo 3L 085 or the DSG. Volkswagen SSP 512, pp. 14, 24 and 28–31.
In the illustrated system, the clutch opens before gear selection and the control unit moves the selector and engagement motors using learnt geometry; it then controls clutch re-engagement. A mechanical clutch and gearbox remain present despite having no clutch pedal. An electric motor, its power/command, feedback, its linkage and the part it moves must be considered as a system; an actuator code does not by itself identify the failed component.
Symptoms and useful evidence
| Observation | Investigation | Limit |
| No crank or N / brake indication | Compare selector request, displayed status and brake input as seen by the relevant controllers. SSP 512 describes an N and brake condition for start authorization in its example. | A rejected request may be a valid interlock or a faulty input; do not bypass it. VW SSP 512, pp. 13 and 29. |
| Request not fulfilled or particular gear unavailable | Record requested and recognized gear, clutch state, transmission and engine faults, voltage and the selection/engagement actuator feedback the correct tool exposes. | The problem can be in an input, control, actuator, wiring, clutch release or mechanical gearbox; an indication is not a parts verdict. |
| Intermittent no-shift or actuator feedback fault | Inspect supply and connectors and compare actuator commands with the related motor feedback using the exact diagnostic plan. Each motor's rotation sensors enable direction and movement to be recognized. | Motor rotation does not prove correct clutch release or gear engagement. The training description is not an approved wiring test or a pinout. |
| Judder, slipping, or overheating warning | Record take-up or driving conditions, warning, engine/input speeds, gear and any related faults. Consider friction clutch condition and actuation as well as engine and driveline causes. | The training manual distinguishes its display states; confirm the instrument's meaning and recovery action in the specific car's handbook. Do not assume every indication is a worn clutch. |
Volkswagen SSP 512 shows gearbox input-speed sender G182 for its documented system. Do not infer a pin assignment, sensor definition or location on another variant from that label alone; verify the current VIN-specific wiring and diagnostic information. The sensor detects the rotating first-gear wheel to determine gearbox input speed, according to the source. Volkswagen SSP 512, p. 30.
Japan up! transmission-control recall: inaccurate position detection
Japan recall 外-2045, filed 18 June 2014 by Volkswagen Group Japan, covers identified VW up! 1.0/55 kW vehicles imported between 26 June 2012 and 17 March 2014. Volkswagen reported that an unsuitable transmission-controller programme could fail to detect gear or clutch position accurately while driving; the transmission might remain in gear or release the clutch, leaving the car coasting and potentially unable to move off after stopping. The prescribed action was to identify the controller and reprogramme it or replace it with an updated unit as applicable. The Japanese Consumer Affairs Agency notice records the same recall. Check VIN, market and campaign history with Volkswagen; this Japanese campaign is not proof that every 0CT or non-Japanese car has the same fault. A position-related symptom also has mechanical, electrical and sensor causes.
Learning and service boundaries
Volkswagen describes a basic setting in which the gear actuator explores the selection and engagement paths and determines their limits. It is an active procedure that moves the mechanism, and is not a general-purpose fix for a mechanical, electrical or supply fault. Before clearing faults or running service functions, save the fault status and relevant data. Follow the current repair sequence, equipment, conditions and learning requirements for the actual repair. Volkswagen SSP 512, pp. 25–26.
That training document cautions against applying grease to the particular clutch-lever ball and socket it illustrates, because grease combined with clutch abrasion can increase wear and noise; it also states that an opened gear actuator must be replaced after removal. These are document- and component-specific instructions, not a universal rule for other systems. Use current Volkswagen workshop instructions before disassembly or lubrication. Volkswagen SSP 512, p. 32.
See Lupo 3L electrohydraulic gearbox, DQ200 dual-clutch diagnosis and the electronic gearbox guide.