Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- DTAFast standalone engine management
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
DTAFast's 30 March 2001 schematic explicitly labels both E48EXP and E48EXP ignition only. The diagram depicts two coil outputs for a wasted-spark example and a 25-position connector. Manufacturer document.
Identification and operating context
This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.
Wiring
The shared schematic also shows injector connections, but that does not establish working fuel drivers in an ignition-only build. Confirm actual hardware, firmware, pin population and connector orientation with DTAFast. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.
E48EXP 25-way wiring schedule
These assignments are transcribed from the DTAFast E48EXP / E48EXP ignition-only schematic dated 30 March 2001. The document shows the common drawing for both models; do not assume injector output hardware is fitted to an ignition-only unit. Match the precise unit and connector view to the original and check electrical limits. Auxiliary outputs are specified as 500 mA maximum; the drawing requires both power-ground positions connected.
PinFunction shown1Lambda signal2Lambda ground3Gear-shift cut switch4Launch control switch55 V sensor supply65 V sensor supply7Sensor ground8Auxiliary 2 output9Tachometer output10Fuel-pump relay output11Gear-change light output12Battery negative / power ground13Battery negative / power ground14Throttle-position wiper15Water temperature signal16Air temperature signal17Pressure sensor signal18Crank sensor signal (VR)19Wheel sensor output (Hall)20Sensor ground / crank sensor return21Injector 2 or idle valve (fuel-equipped build)22Injector 1 (fuel-equipped build)23Coil 224Coil 125Switched 12 V ECU supply
In the schematic, sensor grounds and 5 V outputs are common within their groups except for the separate lambda ground. The manufacturer also provides differing crank-sensor wire positions for Ford, Bosch/Siemens and Marelli sensors; consult the original diagram and do not assume pin order across sensor makes.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: DTAFast E48EXP ignition only
DTAFast's 30 March 2001 schematic explicitly labels both E48EXP and E48EXP ignition only. The diagram depicts two coil outputs for a wasted-spark example and a 25-position connector. Manufacturer document.
Identification and operating context
This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.
Wiring
The shared schematic also shows injector connections, but that does not establish working fuel drivers in an ignition-only build. Confirm actual hardware, firmware, pin population and connector orientation with DTAFast. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.
E48EXP 25-way wiring schedule
These assignments are transcribed from the DTAFast E48EXP / E48EXP ignition-only schematic dated 30 March 2001. The document shows the common drawing for both models; do not assume injector output hardware is fitted to an ignition-only unit. Match the precise unit and connector view to the original and check electrical limits. Auxiliary outputs are specified as 500 mA maximum; the drawing requires both power-ground positions connected.
| Pin | Function shown |
|---|
| 1 | Lambda signal |
| 2 | Lambda ground |
| 3 | Gear-shift cut switch |
| 4 | Launch control switch |
| 5 | 5 V sensor supply |
| 6 | 5 V sensor supply |
| 7 | Sensor ground |
| 8 | Auxiliary 2 output |
| 9 | Tachometer output |
| 10 | Fuel-pump relay output |
| 11 | Gear-change light output |
| 12 | Battery negative / power ground |
| 13 | Battery negative / power ground |
| 14 | Throttle-position wiper |
| 15 | Water temperature signal |
| 16 | Air temperature signal |
| 17 | Pressure sensor signal |
| 18 | Crank sensor signal (VR) |
| 19 | Wheel sensor output (Hall) |
| 20 | Sensor ground / crank sensor return |
| 21 | Injector 2 or idle valve (fuel-equipped build) |
| 22 | Injector 1 (fuel-equipped build) |
| 23 | Coil 2 |
| 24 | Coil 1 |
| 25 | Switched 12 V ECU supply |
In the schematic, sensor grounds and 5 V outputs are common within their groups except for the separate lambda ground. The manufacturer also provides differing crank-sensor wire positions for Ford, Bosch/Siemens and Marelli sensors; consult the original diagram and do not assume pin order across sensor makes.
Revision 2: DTAFast E48EXP ignition only
DTAFast's 30 March 2001 schematic explicitly labels both E48EXP and E48EXP ignition only. The diagram depicts two coil outputs for a wasted-spark example and a 25-position connector. Manufacturer document.
Identification and operating context
This is included for identification as an ignition controller. Record the exact product label, hardware, firmware and loom; do not assume compatibility with a similarly named fuel-and-ignition ECU. See DTAFast family overview.
Wiring
The shared schematic also shows injector connections, but that does not establish working fuel drivers in an ignition-only build. Confirm actual hardware, firmware, pin population and connector orientation with DTAFast. DTAFast wiring reference. Establish fused supplies, grounds, sensor connections and coil-driver limits for the specific unit.
E48EXP 25-way wiring schedule
These assignments are transcribed from the DTAFast E48EXP / E48EXP ignition-only schematic dated 30 March 2001. The document shows the common drawing for both models; do not assume injector output hardware is fitted to an ignition-only unit. Match the precise unit and connector view to the original and check electrical limits. Auxiliary outputs are specified as 500 mA maximum; the drawing requires both power-ground positions connected.
| Pin | Function shown |
|---|
| 1 | Lambda signal |
| 2 | Lambda ground |
| 3 | Gear-shift cut switch |
| 4 | Launch control switch |
| 5 | 5 V sensor supply |
| 6 | 5 V sensor supply |
| 7 | Sensor ground |
| 8 | Auxiliary 2 output |
| 9 | Tachometer output |
| 10 | Fuel-pump relay output |
| 11 | Gear-change light output |
| 12 | Battery negative / power ground |
| 13 | Battery negative / power ground |
| 14 | Throttle-position wiper |
| 15 | Water temperature signal |
| 16 | Air temperature signal |
| 17 | Pressure sensor signal |
| 18 | Crank sensor signal (VR) |
| 19 | Wheel sensor output (Hall) |
| 20 | Sensor ground / crank sensor return |
| 21 | Injector 2 or idle valve (fuel-equipped build) |
| 22 | Injector 1 (fuel-equipped build) |
| 23 | Coil 2 |
| 24 | Coil 1 |
| 25 | Switched 12 V ECU supply |
In the schematic, sensor grounds and 5 V outputs are common within their groups except for the separate lambda ground. The manufacturer also provides differing crank-sensor wire positions for Ford, Bosch/Siemens and Marelli sensors; consult the original diagram and do not assume pin order across sensor makes.