Removed text is struck through; added text is highlighted.
Renault's technical note NT 3815A describes Quickshift diagnosis for Clio II with engine D4F 722 and VDIAG 10, JH1 automated gearbox, December 2006. This article uses that German-language Renault document as a model-specific example. Confirm the vehicle, gearbox, ECU and diagnostic version before applying its codes or procedures; a Quickshift name does not establish identical hardware, pressure limits or software in another Clio, Twingo or van.
Clutch, gearbox and hydraulic system
The Quickshift configuration automates a mechanical manual gearbox and clutch with electrohydraulic actuators. The controller receives driver, brake, speed and engine signals and controls the clutch and selection and engagement functions. The hydraulic unit has a pump, reservoir, accumulator and valves; a conventional manual-gearbox lubrication circuit is a different service item. Renault's NT 3795A gives a separately documented Twingo D4F 708/JH1 example; its mechanical and fluid instructions must not be copied to this Clio or the reverse without matching the applicable service information.
Read conditions and codes together
For this Clio controller, NT 3815A distinguishes present faults from stored faults and directs the technician to record stored entries and apply their stated confirmation conditions. After a full diagnostic check, its conformity section also compares states and parameters that may not themselves generate a fault. The document is not an instruction to clear memory before capturing it. Renault NT 3815A, 21B-1 to 21B-2 and 21B-62.
Documented entryUseful distinction in this controller
DF005 — hydraulic pressure sensor circuitCompare reported pressure, sensor supply and wiring under the prescribed test; an implausible sensor reading does not establish actual hydraulic pressure.
DF065 — pump-relay circuitRenault's branch gives priority to a related DF005 pressure-sensor fault. Check the stated relay, supply, connections and circuit in order rather than assuming that a running or silent pump proves its condition.
DF068 — clutch-position sensor circuitElectrical fault and conformity subtypes are different; inspect sensor mounting, mechanism, connection and wiring as directed before concluding that a clutch or sensor needs replacing.
DF076 — clutch controlRenault distinguishes overheating, learning conformity and shift-related clutch discrepancies. If DF062 CAN and DF076 are both present, the note says to address DF062 first. The fault is not a universal instruction to replace the clutch.
DF078 — hydraulic controlThe listed subtypes distinguish low pressure, pump fault, slow pressure loss, accumulator fault and rapid pressure loss. Check the subtype and test conditions; frequent pumping alone does not distinguish a leak, accumulator, pump or pressure-feedback fault.
DF080 / DF082The document lists battery supply and brake-light/switch circuit faults separately. Confirm controller-visible brake status and supply integrity using the model's test plan.
These descriptions and subtype names come from Renault NT 3815A, 21B-24–27, 21B-34–37 and 21B-46–51; the diagnostic text is for the stated VDIAG. Its DF078 example describes pressure feedback PR018 and pump switching at approximately 40 and 50 bar for that test. Its separate conformity table gives a 40–50 bar range at 20 °C or warmer after the complete diagnosis. Those are document- and condition-specific references, not generic Renault or Easy-R specifications, a direct physical-pressure measurement or proof that a particular component failed.
Symptom-led workflow
Identify the car, controller and service history. Save transmission and engine faults and their present/stored status before performing active tests or clearing data. Record hot/cold, starting, forward/reverse selection, take-up, particular shift, warning and whether the engine is running.
Compare selector request and reported gear, clutch position and the gearbox's selection and engagement feedback, brake state, hydraulic-pressure indication, pump command, battery voltage and relevant engine/CAN signals where the correct tool exposes them.
For no communication, Renault's diagnostic plan first checks the diagnostic equipment and whether it can communicate with other controllers, then relevant supply, earth, fuse, connectors and diagnostic circuit. A no-communication symptom alone does not condemn a gearbox ECU. NT 3815A, diagnostic plan DP 1.
For failed selection, overheating, jerky take-up or recurring pump operation, follow the fault subtype and measured values in the current repair plan. Renault separately lists customer symptoms such as no neutral, loss of automatic mode, no creep and clutch vibration; each requires its own diagnostic branch.
Reservoir level depends on pressure stateA low-looking hydraulic reservoir is not meaningful without knowing the system pressure state. As a separate example, Renault's 2005 Twingo D4F 708 Quickshift manual describes different reservoir levels with the accumulator depressurised and after pressure build-up. Do not transfer its measurements to the Clio: use the current procedure for the exact vehicle, check the prescribed system state and investigate leakage before deciding whether fluid is missing. Incorrect top-up can create a misleading or excessive level when pressure changes. Renault NT 3795A, section 21B (German).Separate Twingo repair-history example: Renault’s NT 3795A for Twingo X062, D4F 708/JH1, says that the electric-pump relay must also be replaced when its electrohydraulic pump is replaced. For a recurring pump complaint after repair, establish exactly what work was done and use the current procedure for the actual vehicle; that Twingo instruction is not evidence that every Clio Quickshift requires the same relay replacement. The third-party reproduction of Renault NT 3795A, printed section 21B-18, may require access.Service and recovery
The hydraulic accumulator can remain charged and an active command can move the clutch or selector. Renault's separately documented Twingo Quickshift procedure requires controlled depressurisation with the diagnostic equipment before opening its electrohydraulic system and pressure confirmation; ignition off is not proof of zero pressure. Follow the exact current vehicle-specific procedure, fluid and post-repair learning steps rather than transferring another model's process or using calibration to mask a defect. Renault NT 3795A, 21B-6 and 21B-9–10.
The Twingo note gives specific recovery precautions if neutral cannot be selected; those instructions are for its documented vehicle and do not establish a universal towing procedure. Consult the actual vehicle's current handbook and recovery service. Related: electronic gearbox guide and Renault and Dacia Easy-R.
Open each version to inspect formatting, tables and photographs.
Revision 1: Renault Clio II Quickshift JH1 operation faults and diagnosis
Renault's technical note NT 3815A describes Quickshift diagnosis for Clio II with engine D4F 722 and VDIAG 10, JH1 automated gearbox, December 2006. This article uses that German-language Renault document as a model-specific example. Confirm the vehicle, gearbox, ECU and diagnostic version before applying its codes or procedures; a Quickshift name does not establish identical hardware, pressure limits or software in another Clio, Twingo or van.
Clutch, gearbox and hydraulic system
The Quickshift configuration automates a mechanical manual gearbox and clutch with electrohydraulic actuators. The controller receives driver, brake, speed and engine signals and controls the clutch and selection and engagement functions. The hydraulic unit has a pump, reservoir, accumulator and valves; a conventional manual-gearbox lubrication circuit is a different service item. Renault's NT 3795A gives a separately documented Twingo D4F 708/JH1 example; its mechanical and fluid instructions must not be copied to this Clio or the reverse without matching the applicable service information.
Read conditions and codes together
For this Clio controller, NT 3815A distinguishes present faults from stored faults and directs the technician to record stored entries and apply their stated confirmation conditions. After a full diagnostic check, its conformity section also compares states and parameters that may not themselves generate a fault. The document is not an instruction to clear memory before capturing it. Renault NT 3815A, 21B-1 to 21B-2 and 21B-62.
| Documented entry | Useful distinction in this controller |
| DF005 — hydraulic pressure sensor circuit | Compare reported pressure, sensor supply and wiring under the prescribed test; an implausible sensor reading does not establish actual hydraulic pressure. |
| DF065 — pump-relay circuit | Renault's branch gives priority to a related DF005 pressure-sensor fault. Check the stated relay, supply, connections and circuit in order rather than assuming that a running or silent pump proves its condition. |
| DF068 — clutch-position sensor circuit | Electrical fault and conformity subtypes are different; inspect sensor mounting, mechanism, connection and wiring as directed before concluding that a clutch or sensor needs replacing. |
| DF076 — clutch control | Renault distinguishes overheating, learning conformity and shift-related clutch discrepancies. If DF062 CAN and DF076 are both present, the note says to address DF062 first. The fault is not a universal instruction to replace the clutch. |
| DF078 — hydraulic control | The listed subtypes distinguish low pressure, pump fault, slow pressure loss, accumulator fault and rapid pressure loss. Check the subtype and test conditions; frequent pumping alone does not distinguish a leak, accumulator, pump or pressure-feedback fault. |
| DF080 / DF082 | The document lists battery supply and brake-light/switch circuit faults separately. Confirm controller-visible brake status and supply integrity using the model's test plan. |
These descriptions and subtype names come from Renault NT 3815A, 21B-24–27, 21B-34–37 and 21B-46–51; the diagnostic text is for the stated VDIAG. Its DF078 example describes pressure feedback PR018 and pump switching at approximately 40 and 50 bar for that test. Its separate conformity table gives a 40–50 bar range at 20 °C or warmer after the complete diagnosis. Those are document- and condition-specific references, not generic Renault or Easy-R specifications, a direct physical-pressure measurement or proof that a particular component failed.
Symptom-led workflow
- Identify the car, controller and service history. Save transmission and engine faults and their present/stored status before performing active tests or clearing data. Record hot/cold, starting, forward/reverse selection, take-up, particular shift, warning and whether the engine is running.
- Compare selector request and reported gear, clutch position and the gearbox's selection and engagement feedback, brake state, hydraulic-pressure indication, pump command, battery voltage and relevant engine/CAN signals where the correct tool exposes them.
- For no communication, Renault's diagnostic plan first checks the diagnostic equipment and whether it can communicate with other controllers, then relevant supply, earth, fuse, connectors and diagnostic circuit. A no-communication symptom alone does not condemn a gearbox ECU. NT 3815A, diagnostic plan DP 1.
- For failed selection, overheating, jerky take-up or recurring pump operation, follow the fault subtype and measured values in the current repair plan. Renault separately lists customer symptoms such as no neutral, loss of automatic mode, no creep and clutch vibration; each requires its own diagnostic branch.
Service and recovery
The hydraulic accumulator can remain charged and an active command can move the clutch or selector. Renault's separately documented Twingo Quickshift procedure requires controlled depressurisation with the diagnostic equipment before opening its electrohydraulic system and pressure confirmation; ignition off is not proof of zero pressure. Follow the exact current vehicle-specific procedure, fluid and post-repair learning steps rather than transferring another model's process or using calibration to mask a defect. Renault NT 3795A, 21B-6 and 21B-9–10.
The Twingo note gives specific recovery precautions if neutral cannot be selected; those instructions are for its documented vehicle and do not establish a universal towing procedure. Consult the actual vehicle's current handbook and recovery service. Related: electronic gearbox guide and Renault and Dacia Easy-R.
Revision 3: Renault Clio II Quickshift JH1 operation faults and diagnosis
Renault's technical note NT 3815A describes Quickshift diagnosis for Clio II with engine D4F 722 and VDIAG 10, JH1 automated gearbox, December 2006. This article uses that German-language Renault document as a model-specific example. Confirm the vehicle, gearbox, ECU and diagnostic version before applying its codes or procedures; a Quickshift name does not establish identical hardware, pressure limits or software in another Clio, Twingo or van.
Clutch, gearbox and hydraulic system
The Quickshift configuration automates a mechanical manual gearbox and clutch with electrohydraulic actuators. The controller receives driver, brake, speed and engine signals and controls the clutch and selection and engagement functions. The hydraulic unit has a pump, reservoir, accumulator and valves; a conventional manual-gearbox lubrication circuit is a different service item. Renault's NT 3795A gives a separately documented Twingo D4F 708/JH1 example; its mechanical and fluid instructions must not be copied to this Clio or the reverse without matching the applicable service information.
Read conditions and codes together
For this Clio controller, NT 3815A distinguishes present faults from stored faults and directs the technician to record stored entries and apply their stated confirmation conditions. After a full diagnostic check, its conformity section also compares states and parameters that may not themselves generate a fault. The document is not an instruction to clear memory before capturing it. Renault NT 3815A, 21B-1 to 21B-2 and 21B-62.
| Documented entry | Useful distinction in this controller |
| DF005 — hydraulic pressure sensor circuit | Compare reported pressure, sensor supply and wiring under the prescribed test; an implausible sensor reading does not establish actual hydraulic pressure. |
| DF065 — pump-relay circuit | Renault's branch gives priority to a related DF005 pressure-sensor fault. Check the stated relay, supply, connections and circuit in order rather than assuming that a running or silent pump proves its condition. |
| DF068 — clutch-position sensor circuit | Electrical fault and conformity subtypes are different; inspect sensor mounting, mechanism, connection and wiring as directed before concluding that a clutch or sensor needs replacing. |
| DF076 — clutch control | Renault distinguishes overheating, learning conformity and shift-related clutch discrepancies. If DF062 CAN and DF076 are both present, the note says to address DF062 first. The fault is not a universal instruction to replace the clutch. |
| DF078 — hydraulic control | The listed subtypes distinguish low pressure, pump fault, slow pressure loss, accumulator fault and rapid pressure loss. Check the subtype and test conditions; frequent pumping alone does not distinguish a leak, accumulator, pump or pressure-feedback fault. |
| DF080 / DF082 | The document lists battery supply and brake-light/switch circuit faults separately. Confirm controller-visible brake status and supply integrity using the model's test plan. |
These descriptions and subtype names come from Renault NT 3815A, 21B-24–27, 21B-34–37 and 21B-46–51; the diagnostic text is for the stated VDIAG. Its DF078 example describes pressure feedback PR018 and pump switching at approximately 40 and 50 bar for that test. Its separate conformity table gives a 40–50 bar range at 20 °C or warmer after the complete diagnosis. Those are document- and condition-specific references, not generic Renault or Easy-R specifications, a direct physical-pressure measurement or proof that a particular component failed.
Symptom-led workflow
- Identify the car, controller and service history. Save transmission and engine faults and their present/stored status before performing active tests or clearing data. Record hot/cold, starting, forward/reverse selection, take-up, particular shift, warning and whether the engine is running.
- Compare selector request and reported gear, clutch position and the gearbox's selection and engagement feedback, brake state, hydraulic-pressure indication, pump command, battery voltage and relevant engine/CAN signals where the correct tool exposes them.
- For no communication, Renault's diagnostic plan first checks the diagnostic equipment and whether it can communicate with other controllers, then relevant supply, earth, fuse, connectors and diagnostic circuit. A no-communication symptom alone does not condemn a gearbox ECU. NT 3815A, diagnostic plan DP 1.
- For failed selection, overheating, jerky take-up or recurring pump operation, follow the fault subtype and measured values in the current repair plan. Renault separately lists customer symptoms such as no neutral, loss of automatic mode, no creep and clutch vibration; each requires its own diagnostic branch.
Reservoir level depends on pressure state
A low-looking hydraulic reservoir is not meaningful without knowing the system pressure state. As a separate example, Renault's 2005 Twingo D4F 708 Quickshift manual describes different reservoir levels with the accumulator depressurised and after pressure build-up. Do not transfer its measurements to the Clio: use the current procedure for the exact vehicle, check the prescribed system state and investigate leakage before deciding whether fluid is missing. Incorrect top-up can create a misleading or excessive level when pressure changes. Renault NT 3795A, section 21B (German).
Separate Twingo repair-history example: Renault’s NT 3795A for Twingo X062, D4F 708/JH1, says that the electric-pump relay must also be replaced when its electrohydraulic pump is replaced. For a recurring pump complaint after repair, establish exactly what work was done and use the current procedure for the actual vehicle; that Twingo instruction is not evidence that every Clio Quickshift requires the same relay replacement. The third-party reproduction of Renault NT 3795A, printed section 21B-18, may require access.
Service and recovery
The hydraulic accumulator can remain charged and an active command can move the clutch or selector. Renault's separately documented Twingo Quickshift procedure requires controlled depressurisation with the diagnostic equipment before opening its electrohydraulic system and pressure confirmation; ignition off is not proof of zero pressure. Follow the exact current vehicle-specific procedure, fluid and post-repair learning steps rather than transferring another model's process or using calibration to mask a defect. Renault NT 3795A, 21B-6 and 21B-9–10.
The Twingo note gives specific recovery precautions if neutral cannot be selected; those instructions are for its documented vehicle and do not establish a universal towing procedure. Consult the actual vehicle's current handbook and recovery service. Related: electronic gearbox guide and Renault and Dacia Easy-R.