Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 997 Turbo S7Plus, with product code S7Plus-997DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 997 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Porsche 997 Turbo S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Plug-in board 26-way accessory connector
The Syvecs 996/997 Turbo S7Plus manual, version 1.2, lists this accessory connector. It labels terminal 12 AN S6 / Slave An06, skipping S5; that numbering is reproduced as printed. Use the manual and actual board to identify orientation, ratings and ECU revision. This is not the full OEM loom connector pinout.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Porsche 997 Turbo S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 997 Turbo S7Plus, with product code S7Plus-997DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 997 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
The Syvecs 996/997 Turbo S7Plus manual, version 1.2, lists this accessory connector. It labels terminal 12 AN S6 / Slave An06, skipping S5; that numbering is reproduced as printed. Use the manual and actual board to identify orientation, ratings and ECU revision. This is not the full OEM loom connector pinout.
Pin
Manufacturer function
1
Ground
2
Fuel 7
3
Fuel 8
4
Fuel 9
5
Fuel 10
6
Fuel 11
7
Fuel 12
8
AN S1 / Slave An01
9
AN S2 / Slave An02
10
AN S3 / Slave An03
11
AN S4 / Slave An04
12
AN S6 / Slave An06
13
12 V
14
CAN2 low
15
CAN2 high
16
EGT1−
17
EGT1+
18
RS232 RX
19
RS232 TX
20
Sensor ground
21
5 V
22
LAM2C
23
LAN RX−
24
LAN RX+
25
LAN TX−
26
LAN TX+
Revision 2: Syvecs Porsche 997 Turbo S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 997 Turbo S7Plus, with product code S7Plus-997DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 997 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
The Syvecs 996/997 Turbo S7Plus manual, version 1.2, lists this accessory connector. It labels terminal 12 AN S6 / Slave An06, skipping S5; that numbering is reproduced as printed. Use the manual and actual board to identify orientation, ratings and ECU revision. This is not the full OEM loom connector pinout.