Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.1 R GTI E888 Gen3 S7Plus, with product code S7Plus-VW7R. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index

Kit controller and DI driver pin schedules

Transcribed from the Syvecs Golf R7 kit manual, pages 5–7. These are Syvecs controller and direct-injection driver connections, not the original car's connector pin numbers. Empty notes mean the manufacturer did not assign a kit function in the schedule. Confirm the exact kit, wiring revision, software configuration and connector orientation; driver channels and sensor assignments can change.

A — 34-way, key 1

PinSyvecs I/OKit function / manufacturer noteA1PWR CTR OUTMain relay outputA2H-Bridge1 / SlaveOut1DBW +A3H-Bridge2 / SlaveOut2DBW −A4H-Bridge3 / SlaveOut3Boost pressure positioner + (V465)A5H-Bridge4 / SlaveOut4Boost pressure positioner − (V465)A6H-Bridge5 / SlaveOut5Turbo recirculationA7H-Bridge6 / SlaveOut6Starter relayA8H-Bridge7 / SlaveOut7Coolant flow control + (N493)A9H-Bridge8 / SlaveOut8Coolant flow control − (N493)A10FUEL1Primary injector 1A11FUEL2Primary injector 2A12FUEL3Primary injector 3A13FUEL4Primary injector 4A14FUEL5Port injector 1 (N532)A15FUEL6Port injector 2 (N533)A16FUEL7Port injector 3 (N534)A17FUEL8Port injector 4 (N535)A18PWM1 / *FUEL9Cooling oil valveA19PWM2 / *FUEL10Intake manifold flap (N316)A20PWM3 / *FUEL11Fuel pump PWMA21PWM4 / *FUEL12Cooling fan PWMA22PWM5 / *FUEL13Exhaust cam AA23PWM6 / *FUEL14Exhaust cam B – power camA24PWM7 / *FUEL15VVT1 intake (N205)A25PWM8 / *FUEL16VVT1 exhaust (N316)A26IGN1Ignition 1 (N70)A27IGN2Ignition 2 (N127)A28IGN3Ignition 3 (N291)A29IGN4Ignition 4 (N292)A30IGN5DI pump signal to DI12A31IGN6Tacho syncA32PWRGNDPower groundA33PWRGNDPower groundA34PWRGNDPower ground

B — 26-way, key 1

PinSyvecs I/OKit function / manufacturer noteB1PWRGNDPower groundB2CAN2L—B3CAN2H—B4KNOCKKnock +B5KNOCK 2—B6PVBATConstant 12 VB7IVBAT12 V (87a), SB3 / J271B8LAM1ALSU 4.9 connector pin 6B9LAM1BLSU 4.9 connector pin 1B10LAM1CLSU 4.9 connector pin 5B11LAM1DLSU 4.9 connector pin 2B12LAM1HEATERLSU 4.9 connector pin 3B13IVBAT12 VB14LAM2A—B15LAM2B—B16LAM2C—B17LAM2D—B18LAM2HEATERSlave Out 10 – evap solenoidB19IVBAT12 VB20KLINE—B21RS232RX—B22RS232TX—B23LANRX−Cat5 pin 2B24LANRX+Cat5 pin 1B25LANTX−Cat5 pin 6B26LANTX+Cat5 pin 3

C — 34-way, key 2

PinSyvecs I/OKit function / manufacturer noteC1KNOCKGNDKnock −C2ANGNDSensor groundC3ANGNDSensor groundC4ANGNDSensor groundC55V OUT—C65V OUT—C75V OUT—C8CAN LPowertrain CANC9CAN HPowertrain CANC10AN01DI pressureC11AN02MAP sensorC12AN03Charge pressure (G31); source queries four-wireC13AN04Low-side fuel pressureC14AN05VVT1 intake positionC15AN06VVT1 exhaust positionC16AN07Crank sensorC17AN08Brake light switchC18AN09TPS1AC19AN10TPS1BC20AN11PPSAC21AN12PPSBC22AN13Coolant temperature (G62)C23AN14Intake air temperatureC24AN15—C25AN16Oil pressure switch 2 barC26EGT1−—C27EGT1+—C28PWR CTR INKey-on signal (15)C29AN S1 / Slave An01Oil level / temperatureC30AN S2 / Slave An02Clutch switchC31AN S3 / Slave An03Cooling thermostat position (N493)C32AN S4 / Slave An04Wastegate position sensor (G581)C33AN S5 / Slave An05Intake position flapC34AN S6 / Slave An06Starter signal

Direct-injection driver — 35-way

PinSyvecs I/OKit function / manufacturer note1LS1Injector 1 −2LS2—3LS3—4LS4—5LS5—6LS6Injector 4 −7LS12—8LS11Injector 2 −9LS10DI pump low signal10LS9—11LS8—12LS7Injector 3 −13Input 1Injector 1 signal14Input 2—15Input 3—16Input 4—17Input 5—18KLINE—19Input 11Injector 2 signal20Input 10DI pump signal21Input 9—22Input 8—23Input 7Injector 3 signal24VBAT112 V25HS1,2Injector 1 +26PWRGNDGround27HS3,4—28HS5,6Injector 4 +29Input 6Injector 4 signal30Input 12—31HS11,12Injector 2 +32HS9,10DI pump high side33PWRGNDGround34HS7,8Injector 3 +35VBAT212 V

The source lists B18 as LAM2HEATER hardware used for Slave Out 10 / evap solenoid. It also repeats lambda-1 software labels alongside LAM2A–D; the wiring table above preserves the channel names rather than inferring different lambda assignments.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.1 R GTI E888 Gen3 S7Plus, with product code S7Plus-VW7R. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Kit controller and DI driver pin schedules

Transcribed from the Syvecs Golf R7 kit manual, pages 5–7. These are Syvecs controller and direct-injection driver connections, not the original car's connector pin numbers. Empty notes mean the manufacturer did not assign a kit function in the schedule. Confirm the exact kit, wiring revision, software configuration and connector orientation; driver channels and sensor assignments can change.

A — 34-way, key 1

PinSyvecs I/OKit function / manufacturer note
A1PWR CTR OUTMain relay output
A2H-Bridge1 / SlaveOut1DBW +
A3H-Bridge2 / SlaveOut2DBW −
A4H-Bridge3 / SlaveOut3Boost pressure positioner + (V465)
A5H-Bridge4 / SlaveOut4Boost pressure positioner − (V465)
A6H-Bridge5 / SlaveOut5Turbo recirculation
A7H-Bridge6 / SlaveOut6Starter relay
A8H-Bridge7 / SlaveOut7Coolant flow control + (N493)
A9H-Bridge8 / SlaveOut8Coolant flow control − (N493)
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Port injector 1 (N532)
A15FUEL6Port injector 2 (N533)
A16FUEL7Port injector 3 (N534)
A17FUEL8Port injector 4 (N535)
A18PWM1 / *FUEL9Cooling oil valve
A19PWM2 / *FUEL10Intake manifold flap (N316)
A20PWM3 / *FUEL11Fuel pump PWM
A21PWM4 / *FUEL12Cooling fan PWM
A22PWM5 / *FUEL13Exhaust cam A
A23PWM6 / *FUEL14Exhaust cam B – power cam
A24PWM7 / *FUEL15VVT1 intake (N205)
A25PWM8 / *FUEL16VVT1 exhaust (N316)
A26IGN1Ignition 1 (N70)
A27IGN2Ignition 2 (N127)
A28IGN3Ignition 3 (N291)
A29IGN4Ignition 4 (N292)
A30IGN5DI pump signal to DI12
A31IGN6Tacho sync
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

B — 26-way, key 1

PinSyvecs I/OKit function / manufacturer note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCKKnock +
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V (87a), SB3 / J271
B8LAM1ALSU 4.9 connector pin 6
B9LAM1BLSU 4.9 connector pin 1
B10LAM1CLSU 4.9 connector pin 5
B11LAM1DLSU 4.9 connector pin 2
B12LAM1HEATERLSU 4.9 connector pin 3
B13IVBAT12 V
B14LAM2A—
B15LAM2B—
B16LAM2C—
B17LAM2D—
B18LAM2HEATERSlave Out 10 – evap solenoid
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

C — 34-way, key 2

PinSyvecs I/OKit function / manufacturer note
C1KNOCKGNDKnock −
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN LPowertrain CAN
C9CAN HPowertrain CAN
C10AN01DI pressure
C11AN02MAP sensor
C12AN03Charge pressure (G31); source queries four-wire
C13AN04Low-side fuel pressure
C14AN05VVT1 intake position
C15AN06VVT1 exhaust position
C16AN07Crank sensor
C17AN08Brake light switch
C18AN09TPS1A
C19AN10TPS1B
C20AN11PPSA
C21AN12PPSB
C22AN13Coolant temperature (G62)
C23AN14Intake air temperature
C24AN15—
C25AN16Oil pressure switch 2 bar
C26EGT1−—
C27EGT1+—
C28PWR CTR INKey-on signal (15)
C29AN S1 / Slave An01Oil level / temperature
C30AN S2 / Slave An02Clutch switch
C31AN S3 / Slave An03Cooling thermostat position (N493)
C32AN S4 / Slave An04Wastegate position sensor (G581)
C33AN S5 / Slave An05Intake position flap
C34AN S6 / Slave An06Starter signal

Direct-injection driver — 35-way

PinSyvecs I/OKit function / manufacturer note
1LS1Injector 1 −
2LS2—
3LS3—
4LS4—
5LS5—
6LS6Injector 4 −
7LS12—
8LS11Injector 2 −
9LS10DI pump low signal
10LS9—
11LS8—
12LS7Injector 3 −
13Input 1Injector 1 signal
14Input 2—
15Input 3—
16Input 4—
17Input 5—
18KLINE—
19Input 11Injector 2 signal
20Input 10DI pump signal
21Input 9—
22Input 8—
23Input 7Injector 3 signal
24VBAT112 V
25HS1,2Injector 1 +
26PWRGNDGround
27HS3,4—
28HS5,6Injector 4 +
29Input 6Injector 4 signal
30Input 12—
31HS11,12Injector 2 +
32HS9,10DI pump high side
33PWRGNDGround
34HS7,8Injector 3 +
35VBAT212 V

The source lists B18 as LAM2HEATER hardware used for Slave Out 10 / evap solenoid. It also repeats lambda-1 software labels alongside LAM2A–D; the wiring table above preserves the channel names rather than inferring different lambda assignments.

Revision 2: Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.1 R GTI E888 Gen3 S7Plus, with product code S7Plus-VW7R. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Kit controller and DI driver pin schedules

Transcribed from the Syvecs Golf R7 kit manual, pages 5–7. These are Syvecs controller and direct-injection driver connections, not the original car's connector pin numbers. Empty notes mean the manufacturer did not assign a kit function in the schedule. Confirm the exact kit, wiring revision, software configuration and connector orientation; driver channels and sensor assignments can change.

A — 34-way, key 1

PinSyvecs I/OKit function / manufacturer note
A1PWR CTR OUTMain relay output
A2H-Bridge1 / SlaveOut1DBW +
A3H-Bridge2 / SlaveOut2DBW −
A4H-Bridge3 / SlaveOut3Boost pressure positioner + (V465)
A5H-Bridge4 / SlaveOut4Boost pressure positioner − (V465)
A6H-Bridge5 / SlaveOut5Turbo recirculation
A7H-Bridge6 / SlaveOut6Starter relay
A8H-Bridge7 / SlaveOut7Coolant flow control + (N493)
A9H-Bridge8 / SlaveOut8Coolant flow control − (N493)
A10FUEL1Primary injector 1
A11FUEL2Primary injector 2
A12FUEL3Primary injector 3
A13FUEL4Primary injector 4
A14FUEL5Port injector 1 (N532)
A15FUEL6Port injector 2 (N533)
A16FUEL7Port injector 3 (N534)
A17FUEL8Port injector 4 (N535)
A18PWM1 / *FUEL9Cooling oil valve
A19PWM2 / *FUEL10Intake manifold flap (N316)
A20PWM3 / *FUEL11Fuel pump PWM
A21PWM4 / *FUEL12Cooling fan PWM
A22PWM5 / *FUEL13Exhaust cam A
A23PWM6 / *FUEL14Exhaust cam B – power cam
A24PWM7 / *FUEL15VVT1 intake (N205)
A25PWM8 / *FUEL16VVT1 exhaust (N316)
A26IGN1Ignition 1 (N70)
A27IGN2Ignition 2 (N127)
A28IGN3Ignition 3 (N291)
A29IGN4Ignition 4 (N292)
A30IGN5DI pump signal to DI12
A31IGN6Tacho sync
A32PWRGNDPower ground
A33PWRGNDPower ground
A34PWRGNDPower ground

B — 26-way, key 1

PinSyvecs I/OKit function / manufacturer note
B1PWRGNDPower ground
B2CAN2L—
B3CAN2H—
B4KNOCKKnock +
B5KNOCK 2—
B6PVBATConstant 12 V
B7IVBAT12 V (87a), SB3 / J271
B8LAM1ALSU 4.9 connector pin 6
B9LAM1BLSU 4.9 connector pin 1
B10LAM1CLSU 4.9 connector pin 5
B11LAM1DLSU 4.9 connector pin 2
B12LAM1HEATERLSU 4.9 connector pin 3
B13IVBAT12 V
B14LAM2A—
B15LAM2B—
B16LAM2C—
B17LAM2D—
B18LAM2HEATERSlave Out 10 – evap solenoid
B19IVBAT12 V
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX−Cat5 pin 2
B24LANRX+Cat5 pin 1
B25LANTX−Cat5 pin 6
B26LANTX+Cat5 pin 3

C — 34-way, key 2

PinSyvecs I/OKit function / manufacturer note
C1KNOCKGNDKnock −
C2ANGNDSensor ground
C3ANGNDSensor ground
C4ANGNDSensor ground
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN LPowertrain CAN
C9CAN HPowertrain CAN
C10AN01DI pressure
C11AN02MAP sensor
C12AN03Charge pressure (G31); source queries four-wire
C13AN04Low-side fuel pressure
C14AN05VVT1 intake position
C15AN06VVT1 exhaust position
C16AN07Crank sensor
C17AN08Brake light switch
C18AN09TPS1A
C19AN10TPS1B
C20AN11PPSA
C21AN12PPSB
C22AN13Coolant temperature (G62)
C23AN14Intake air temperature
C24AN15—
C25AN16Oil pressure switch 2 bar
C26EGT1−—
C27EGT1+—
C28PWR CTR INKey-on signal (15)
C29AN S1 / Slave An01Oil level / temperature
C30AN S2 / Slave An02Clutch switch
C31AN S3 / Slave An03Cooling thermostat position (N493)
C32AN S4 / Slave An04Wastegate position sensor (G581)
C33AN S5 / Slave An05Intake position flap
C34AN S6 / Slave An06Starter signal

Direct-injection driver — 35-way

PinSyvecs I/OKit function / manufacturer note
1LS1Injector 1 −
2LS2—
3LS3—
4LS4—
5LS5—
6LS6Injector 4 −
7LS12—
8LS11Injector 2 −
9LS10DI pump low signal
10LS9—
11LS8—
12LS7Injector 3 −
13Input 1Injector 1 signal
14Input 2—
15Input 3—
16Input 4—
17Input 5—
18KLINE—
19Input 11Injector 2 signal
20Input 10DI pump signal
21Input 9—
22Input 8—
23Input 7Injector 3 signal
24VBAT112 V
25HS1,2Injector 1 +
26PWRGNDGround
27HS3,4—
28HS5,6Injector 4 +
29Input 6Injector 4 signal
30Input 12—
31HS11,12Injector 2 +
32HS9,10DI pump high side
33PWRGNDGround
34HS7,8Injector 3 +
35VBAT212 V

The source lists B18 as LAM2HEATER hardware used for Slave Out 10 / evap solenoid. It also repeats lambda-1 software labels alongside LAM2A–D; the wiring table above preserves the channel names rather than inferring different lambda assignments.