
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Golf Mk7.1 R GTI E888 Gen3 S7Plus, with product code S7Plus-VW7R. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Golf Mk7.1 R GTI E888 Gen3 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Kit controller and DI driver pin schedules
Transcribed from the Syvecs Golf R7 kit manual, pages 5–7. These are Syvecs controller and direct-injection driver connections, not the original car's connector pin numbers. Empty notes mean the manufacturer did not assign a kit function in the schedule. Confirm the exact kit, wiring revision, software configuration and connector orientation; driver channels and sensor assignments can change.
A — 34-way, key 1
| Pin | Syvecs I/O | Kit function / manufacturer note |
|---|---|---|
| A1 | PWR CTR OUT | Main relay output |
| A2 | H-Bridge1 / SlaveOut1 | DBW + |
| A3 | H-Bridge2 / SlaveOut2 | DBW − |
| A4 | H-Bridge3 / SlaveOut3 | Boost pressure positioner + (V465) |
| A5 | H-Bridge4 / SlaveOut4 | Boost pressure positioner − (V465) |
| A6 | H-Bridge5 / SlaveOut5 | Turbo recirculation |
| A7 | H-Bridge6 / SlaveOut6 | Starter relay |
| A8 | H-Bridge7 / SlaveOut7 | Coolant flow control + (N493) |
| A9 | H-Bridge8 / SlaveOut8 | Coolant flow control − (N493) |
| A10 | FUEL1 | Primary injector 1 |
| A11 | FUEL2 | Primary injector 2 |
| A12 | FUEL3 | Primary injector 3 |
| A13 | FUEL4 | Primary injector 4 |
| A14 | FUEL5 | Port injector 1 (N532) |
| A15 | FUEL6 | Port injector 2 (N533) |
| A16 | FUEL7 | Port injector 3 (N534) |
| A17 | FUEL8 | Port injector 4 (N535) |
| A18 | PWM1 / *FUEL9 | Cooling oil valve |
| A19 | PWM2 / *FUEL10 | Intake manifold flap (N316) |
| A20 | PWM3 / *FUEL11 | Fuel pump PWM |
| A21 | PWM4 / *FUEL12 | Cooling fan PWM |
| A22 | PWM5 / *FUEL13 | Exhaust cam A |
| A23 | PWM6 / *FUEL14 | Exhaust cam B – power cam |
| A24 | PWM7 / *FUEL15 | VVT1 intake (N205) |
| A25 | PWM8 / *FUEL16 | VVT1 exhaust (N316) |
| A26 | IGN1 | Ignition 1 (N70) |
| A27 | IGN2 | Ignition 2 (N127) |
| A28 | IGN3 | Ignition 3 (N291) |
| A29 | IGN4 | Ignition 4 (N292) |
| A30 | IGN5 | DI pump signal to DI12 |
| A31 | IGN6 | Tacho sync |
| A32 | PWRGND | Power ground |
| A33 | PWRGND | Power ground |
| A34 | PWRGND | Power ground |
B — 26-way, key 1
| Pin | Syvecs I/O | Kit function / manufacturer note |
|---|---|---|
| B1 | PWRGND | Power ground |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | Knock + |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | Constant 12 V |
| B7 | IVBAT | 12 V (87a), SB3 / J271 |
| B8 | LAM1A | LSU 4.9 connector pin 6 |
| B9 | LAM1B | LSU 4.9 connector pin 1 |
| B10 | LAM1C | LSU 4.9 connector pin 5 |
| B11 | LAM1D | LSU 4.9 connector pin 2 |
| B12 | LAM1HEATER | LSU 4.9 connector pin 3 |
| B13 | IVBAT | 12 V |
| B14 | LAM2A | — |
| B15 | LAM2B | — |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | Slave Out 10 – evap solenoid |
| B19 | IVBAT | 12 V |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX− | Cat5 pin 2 |
| B24 | LANRX+ | Cat5 pin 1 |
| B25 | LANTX− | Cat5 pin 6 |
| B26 | LANTX+ | Cat5 pin 3 |
C — 34-way, key 2
| Pin | Syvecs I/O | Kit function / manufacturer note |
|---|---|---|
| C1 | KNOCKGND | Knock − |
| C2 | ANGND | Sensor ground |
| C3 | ANGND | Sensor ground |
| C4 | ANGND | Sensor ground |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | Powertrain CAN |
| C9 | CAN H | Powertrain CAN |
| C10 | AN01 | DI pressure |
| C11 | AN02 | MAP sensor |
| C12 | AN03 | Charge pressure (G31); source queries four-wire |
| C13 | AN04 | Low-side fuel pressure |
| C14 | AN05 | VVT1 intake position |
| C15 | AN06 | VVT1 exhaust position |
| C16 | AN07 | Crank sensor |
| C17 | AN08 | Brake light switch |
| C18 | AN09 | TPS1A |
| C19 | AN10 | TPS1B |
| C20 | AN11 | PPSA |
| C21 | AN12 | PPSB |
| C22 | AN13 | Coolant temperature (G62) |
| C23 | AN14 | Intake air temperature |
| C24 | AN15 | — |
| C25 | AN16 | Oil pressure switch 2 bar |
| C26 | EGT1− | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Key-on signal (15) |
| C29 | AN S1 / Slave An01 | Oil level / temperature |
| C30 | AN S2 / Slave An02 | Clutch switch |
| C31 | AN S3 / Slave An03 | Cooling thermostat position (N493) |
| C32 | AN S4 / Slave An04 | Wastegate position sensor (G581) |
| C33 | AN S5 / Slave An05 | Intake position flap |
| C34 | AN S6 / Slave An06 | Starter signal |
Direct-injection driver — 35-way
| Pin | Syvecs I/O | Kit function / manufacturer note |
|---|---|---|
| 1 | LS1 | Injector 1 − |
| 2 | LS2 | — |
| 3 | LS3 | — |
| 4 | LS4 | — |
| 5 | LS5 | — |
| 6 | LS6 | Injector 4 − |
| 7 | LS12 | — |
| 8 | LS11 | Injector 2 − |
| 9 | LS10 | DI pump low signal |
| 10 | LS9 | — |
| 11 | LS8 | — |
| 12 | LS7 | Injector 3 − |
| 13 | Input 1 | Injector 1 signal |
| 14 | Input 2 | — |
| 15 | Input 3 | — |
| 16 | Input 4 | — |
| 17 | Input 5 | — |
| 18 | KLINE | — |
| 19 | Input 11 | Injector 2 signal |
| 20 | Input 10 | DI pump signal |
| 21 | Input 9 | — |
| 22 | Input 8 | — |
| 23 | Input 7 | Injector 3 signal |
| 24 | VBAT1 | 12 V |
| 25 | HS1,2 | Injector 1 + |
| 26 | PWRGND | Ground |
| 27 | HS3,4 | — |
| 28 | HS5,6 | Injector 4 + |
| 29 | Input 6 | Injector 4 signal |
| 30 | Input 12 | — |
| 31 | HS11,12 | Injector 2 + |
| 32 | HS9,10 | DI pump high side |
| 33 | PWRGND | Ground |
| 34 | HS7,8 | Injector 3 + |
| 35 | VBAT2 | 12 V |
The source lists B18 as LAM2HEATER hardware used for Slave Out 10 / evap solenoid. It also repeats lambda-1 software labels alongside LAM2A–D; the wiring table above preserves the channel names rather than inferring different lambda assignments.