Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1993-1997 non-VVTi S7Plus, with product code S7Plus-TSUPRA. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page describes 1993–1997 non-VVTi, whereas the linked manual filename refers to 1994–1998. Confirm ECU connector, production date and engine specification before installation.
Wiring and pinout
Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
S7Plus ECU-to-car connector schedule
These 94 assignments are from the Syvecs Supra 1994–1998 S7Plus kit manual, version 1.2. The product listing describes 1993–1997 non-VVTi; confirm the actual loom, engine, year and gearbox with Syvecs because the stated ranges differ. The table is explicitly headed S7Plus in the source, even though its kit contents also mention S7-i. Blank cells are not proof a cavity is unused.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1993-1997 non-VVTi S7Plus, with product code S7Plus-TSUPRA. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page describes 1993–1997 non-VVTi, whereas the linked manual filename refers to 1994–1998. Confirm ECU connector, production date and engine specification before installation.
Wiring and pinout
Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
These 94 assignments are from the Syvecs Supra 1994–1998 S7Plus kit manual, version 1.2. The product listing describes 1993–1997 non-VVTi; confirm the actual loom, engine, year and gearbox with Syvecs because the stated ranges differ. The table is explicitly headed S7Plus in the source, even though its kit contents also mention S7-i. Blank cells are not proof a cavity is unused.
S7Plus pin
Syvecs signal
Car pin and note in source
A1
PWR CTR OUT
A2
H‐Bridge1 / SlaveOut1
10B | S1 Auto Solenoid
A3
H‐Bridge2 / SlaveOut2
9B | S2 Auto Solenoid
A4
H‐Bridge3 / SlaveOut3
23A | A/C Clutch
A5
H‐Bridge4 / SlaveOut4
60B | Boost Solenoid
A6
H‐Bridge5 / SlaveOut5
33B | Idle 1
A7
H‐Bridge6 / SlaveOut6
35B | Idle 2
A8
H‐Bridge7 / SlaveOut7
34B | Idle 3
A9
H‐Bridge8 / SlaveOut8
32B | Idle 4
A10
FUEL1
20B | Injector1
A11
FUEL2
19B | Injector2
A12
FUEL3
18B | Injector3
A13
FUEL4
17B | Injector4
A14
FUEL5
16B | Injector5
A15
FUEL6
15B | Injector6
A16
FUEL7
Secondary Injector 1
A17
FUEL8
Secondary Injector 2
A18
PWM1 /*FUEL9
16A | Tacho ‐ Needs 12v Pullup
A19
PWM2 / *FUEL10
Secondary Injector 3
A20
PWM3 / *FUEL11
Secondary Injector 4
A21
PWM4 / *FUEL12
22A | Fuel Pump ‐ Needs 5v pull-up
A22
PWM5
Secondary Injector 5
A23
PWM6
Secondary Injector 6
A24
PWM7
13B | SLN ‐ Needs Flyback
A25
PWM8
12B | SLT ‐ Needs Flyback
A26
IGN1
57B | Ignition 1
A27
IGN2
56B | Ignition 2
A28
IGN3
55B | Ignition 3
A29
IGN4
54B | Ignition 4
A30
IGN5
53B | Ignition 5
A31
IGN6
52B | Ignition 6
A32
PWRGND
69B
A33
PWRGND
79B
A34
PWRGND
B1
PWRGND
80B
B2
CAN2L
B3
CAN2H
B4
KNOCK
External Knock loom
B5
KNOCK 2
External Knock loom
B6
PVBAT
B7
IVBAT
31A | 12v
B8
LAM1A
Nernst Cell
B9
LAM1B
Ion Pump
B10
LAM1C
Cal Trim Resistor
B11
LAM1D
Virtual Ground
B12
LAM1HEATER
B13
IVBAT
B14
LAM2A
Nernst Cell
B15
LAM2B
Ion Pump
B16
LAM2C
Cal Trim Resistor
B17
LAM2D
Virtual Ground
B18
LAM2HEATER
B19
IVBAT
31B | Auto Solenoids 12v
B20
KLINE
B21
RS232RX
B22
RS232TX
B23
LANRX‐
B24
LANRX+
B25
LANTX‐
B26
LANTX+
C1
KNOCKGND
External Loom
C2
ANGND
1B, 3B, 7B, 65B
C3
ANGND
C4
ANGND
C5
5V OUT
41B
C6
5V OUT
C7
5V OUT
C8
CAN L
C9
CAN H
C10
AN01
26B | G1
C11
AN02
27B | NE
C12
AN03
External | FL ABS
C13
AN04
External | RL ABS
C14
AN05
34A | A/C Switch
C15
AN06
21B | Overdrive Clutch Speed
C16
AN07
2A | Gearbox Speed
C17
AN08
C18
AN09
43B | VTA
C19
AN10
62B | Map Input
C20
AN11
External | Oil Pressure Signal
C21
AN12
External | Fuel Pressure Signal
C22
AN13
44B | Coolent Temp
C23
AN14
45B | Air temp
C24
AN15
External | Cal Swithc
C25
AN16
External | Traction Swithc
C26
EGT1-
C27
EGT1+
C28
PWR CTR IN
C29
AN S1 / Slave An01
7A | R Switch
C30
AN S2 / Slave An02
External | Up Switch
C31
AN S3 / Slave An03
External | Down Switch
C32
AN S4 / Slave An04
28A | Overdrive Sw
C33
AN S5 / Slave An05
24B | Auto Trans Temp
C34
AN S6 / Slave An06
76B | Park/Neutral Pos
Revision 2: Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1993-1997 non-VVTi S7Plus, with product code S7Plus-TSUPRA. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Application discrepancy: the product page describes 1993–1997 non-VVTi, whereas the linked manual filename refers to 1994–1998. Confirm ECU connector, production date and engine specification before installation.
Wiring and pinout
Syvecs Toyota Supra 1993-1997 non-VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
These 94 assignments are from the Syvecs Supra 1994–1998 S7Plus kit manual, version 1.2. The product listing describes 1993–1997 non-VVTi; confirm the actual loom, engine, year and gearbox with Syvecs because the stated ranges differ. The table is explicitly headed S7Plus in the source, even though its kit contents also mention S7-i. Blank cells are not proof a cavity is unused.