Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Toyota Supra 1998-2000 VVTi S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
S7Plus ECU-to-car connector schedule
These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.
Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Toyota Supra 1998-2000 VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.
Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.
S7Plus pin
Syvecs signal
Car pin and note in source
A1
PWR CTR OUT
A2
H‐Bridge1 / SlaveOut1
7D | DBW
A3
H‐Bridge2 / SlaveOut2
8D | DBW
A4
H‐Bridge3 / SlaveOut3
1F | S1 Auto Solenoid
A5
H‐Bridge4 / SlaveOut4
2F | S2 Auto Solenoid
A6
H‐Bridge5 / SlaveOut5
3F | SD Auto Solenoid
A7
H‐Bridge6 / SlaveOut6
6F | S4 Auto Solenoid
A8
H‐Bridge7 / SlaveOut7
VSV ‐ Intake Control
A9
H‐Bridge8 / SlaveOut8
VSV ‐ Exhaust Control
A10
FUEL1
E5 | Injector1
A11
FUEL2
E6 | Injector2
A12
FUEL3
D1 | Injector3
A13
FUEL4
D2 | Injector4
A14
FUEL5
D3 | Injector5
A15
FUEL6
D4 | Injector6
A16
FUEL7
VSV ‐ Exhaust Bypass
A17
FUEL8
C6 | Knock Light
A18
PWM1 /*FUEL9
G20 | Tacho ‐ Needs 12v Pullup
A19
PWM2 / *FUEL10
G13 | A/C Clutch
A20
PWM3 / *FUEL11
D15 | Boost Solenoid
A21
PWM4 / *FUEL12
A22
PWM5
D17 | VVT
A23
PWM6
15F | SLT ‐ Needs Flyback
A24
PWM7
13F | SLU ‐ Needs Flyback
A25
PWM8
14F | SLN ‐ Needs Flyback
A26
IGN1
D11 | Ignition 1
A27
IGN2
D12 | Ignition 2
A28
IGN3
D13 | Ignition 3
A29
IGN4
C5 | Fuel Pump
A30
IGN5
Ignition 5
A31
IGN6
Ignition 6
A32
PWRGND
D19 | DBW Clutch Ground
A33
PWRGND
D21
A34
PWRGND
D31
B1
PWRGND
E1
B2
CAN2L
B3
CAN2H
B4
KNOCK
External Knock Loom
B5
KNOCK 2
External Knock Loom
B6
PVBAT
B7
IVBAT
C16,C8, D20 | 12v
B8
LAM1A
Nernst Cell
B9
LAM1B
Ion Pump
B10
LAM1C
Cal Trim Resistor
B11
LAM1D
Virtual Ground
B12
LAM1HEATER
B13
IVBAT
D18, F7, F8, F9 | VVTI + / Auto Solenoids 12v
B14
LAM2A
Nernst Cell
B15
LAM2B
Ion Pump
B16
LAM2C
Cal Trim Resistor
B17
LAM2D
Virtual Ground
B18
LAM2HEATER
B19
IVBAT
Lambda 12v
B20
KLINE
B21
RS232RX
B22
RS232TX
B23
LANRX‐
B24
LANRX+
B25
LANTX‐
B26
LANTX+
C1
KNOCKGND
External Loom
C2
ANGND
D22, E18
C3
ANGND
10F, 11F | Auto Box sensor Grounds
C4
ANGND
C5
5V OUT
E2
C6
5V OUT
C7
5V OUT
C8
CAN L
C9
CAN H
C10
AN01
D10 | G1
C11
AN02
D23 | NE
C12
AN03
G18 | RR ABS
C13
AN04
C14
AN05
H7 | FR ABS
C15
AN06
H8 | FL ABS
C16
AN07
5F | AT Speed
C17
AN08
E24 | TPS2
C18
AN09
E15 | PPS1
C19
AN10
E23 | TPS1
C20
AN11
E9 | MAP
C21
AN12
E16 | PPS2
C22
AN13
E14 | Coolent Temp
C23
AN14
E22 | Air temp
C24
AN15
Cal Switch
C25
AN16
G1 | A/C
C26
EGT1-
C27
EGT1+
C28
PWR CTR IN
C29
AN S1 / Slave An01
G16 | R Switch
C30
AN S2 / Slave An02
G4 | Up Switch
C31
AN S3 / Slave An03
G14 | Down Switch
C32
AN S4 / Slave An04
G7 | Manual Mode
C33
AN S5 / Slave An05
F17 | Auto Trans Temp
C34
AN S6 / Slave An06
G27 | N And R Switch
Revision 2: Syvecs Toyota Supra 1998-2000 VVTi S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.
Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.