Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Toyota Supra 1998-2000 VVTi S7Plus, with product code S7Plus-TSUPRA-1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Toyota Supra 1998-2000 VVTi S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

S7Plus ECU-to-car connector schedule

These 94 assignments are transcribed from the Syvecs Supra 1998–2000 S7Plus kit manual, version 1.2. The left column is the S7Plus ECU cavity; the other columns preserve its signal and the car pin or note given by Syvecs. Empty source fields are not proof that a cavity or vehicle wire is unused. Verify transmission, loom, hardware and connector orientation against Syvecs before wiring.

Source ambiguity: the table uses car pin G1 for both C10 (AN01) and C25 (AN16), with different functions. The manual's boost FAQ also refers to an S6Plus, so confirm the intended pin and kit configuration rather than resolving these by assumption.

S7Plus pinSyvecs signalCar pin and note in source
A1PWR CTR OUT
A2H‐Bridge1 / SlaveOut17D | DBW
A3H‐Bridge2 / SlaveOut28D | DBW
A4H‐Bridge3 / SlaveOut31F | S1 Auto Solenoid
A5H‐Bridge4 / SlaveOut42F | S2 Auto Solenoid
A6H‐Bridge5 / SlaveOut53F | SD Auto Solenoid
A7H‐Bridge6 / SlaveOut66F | S4 Auto Solenoid
A8H‐Bridge7 / SlaveOut7VSV ‐ Intake Control
A9H‐Bridge8 / SlaveOut8VSV ‐ Exhaust Control
A10FUEL1E5 | Injector1
A11FUEL2E6 | Injector2
A12FUEL3D1 | Injector3
A13FUEL4D2 | Injector4
A14FUEL5D3 | Injector5
A15FUEL6D4 | Injector6
A16FUEL7VSV ‐ Exhaust Bypass
A17FUEL8C6 | Knock Light
A18PWM1 /*FUEL9G20 | Tacho ‐ Needs 12v Pullup
A19PWM2 / *FUEL10G13 | A/C Clutch
A20PWM3 / *FUEL11D15 | Boost Solenoid
A21PWM4 / *FUEL12
A22PWM5D17 | VVT
A23PWM615F | SLT ‐ Needs Flyback
A24PWM713F | SLU ‐ Needs Flyback
A25PWM814F | SLN ‐ Needs Flyback
A26IGN1D11 | Ignition 1
A27IGN2D12 | Ignition 2
A28IGN3D13 | Ignition 3
A29IGN4C5 | Fuel Pump
A30IGN5Ignition 5
A31IGN6Ignition 6
A32PWRGNDD19 | DBW Clutch Ground
A33PWRGNDD21
A34PWRGNDD31
B1PWRGNDE1
B2CAN2L
B3CAN2H
B4KNOCKExternal Knock Loom
B5KNOCK 2External Knock Loom
B6PVBAT
B7IVBATC16,C8, D20 | 12v
B8LAM1ANernst Cell
B9LAM1BIon Pump
B10LAM1CCal Trim Resistor
B11LAM1DVirtual Ground
B12LAM1HEATER
B13IVBATD18, F7, F8, F9 | VVTI + / Auto Solenoids 12v
B14LAM2ANernst Cell
B15LAM2BIon Pump
B16LAM2CCal Trim Resistor
B17LAM2DVirtual Ground
B18LAM2HEATER
B19IVBATLambda 12v
B20KLINE
B21RS232RX
B22RS232TX
B23LANRX‐
B24LANRX+
B25LANTX‐
B26LANTX+
C1KNOCKGNDExternal Loom
C2ANGNDD22, E18
C3ANGND10F, 11F | Auto Box sensor Grounds
C4ANGND
C55V OUTE2
C65V OUT
C75V OUT
C8CAN L
C9CAN H
C10AN01D10 | G1
C11AN02D23 | NE
C12AN03G18 | RR ABS
C13AN04
C14AN05H7 | FR ABS
C15AN06H8 | FL ABS
C16AN075F | AT Speed
C17AN08E24 | TPS2
C18AN09E15 | PPS1
C19AN10E23 | TPS1
C20AN11E9 | MAP
C21AN12E16 | PPS2
C22AN13E14 | Coolent Temp
C23AN14E22 | Air temp
C24AN15Cal Switch
C25AN16G1 | A/C
C26EGT1-
C27EGT1+
C28PWR CTR IN
C29AN S1 / Slave An01G16 | R Switch
C30AN S2 / Slave An02G4 | Up Switch
C31AN S3 / Slave An03G14 | Down Switch
C32AN S4 / Slave An04G7 | Manual Mode
C33AN S5 / Slave An05F17 | Auto Trans Temp
C34AN S6 / Slave An06G27 | N And R Switch