Wolf V550 is a standalone or earlier programmable engine-management system. AiM's Wolf racing ECU reference separately identifies the V550. Confirm firmware and wiring for the actual unit. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Wolf V550 wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
V550 connector pinout
These tables transcribe the Wolf V550 wiring drawing dated 14 July 2013, revision 001; its connector A drawing also appears in the V550 operation manual, illustration 1.5.2. Read the source for connector orientation, wire colours, output ratings and electrical requirements.
Source conflict: The 2013 Wolf drawing's table describes B25 as dashboard-control communications while its schematic marks B25 unused, and marks B26 unused. A later AiM V550 interface guide identifies B25 and B26 as CAN high and CAN low. Verify the particular hardware and revision with Wolf before wiring these positions.
Connector A — 34 positions
| Pin | Function in 2013 Wolf diagram |
|---|---|
| A1 | +12 V input |
| A2 | A/C request input |
| A3 | Idle air PWM output |
| A4 | Injector output 1 |
| A5 | Injector output 2 |
| A6 | Injector output 3 |
| A7 | Injector output 4 |
| A8 | Injector output 5 |
| A9 | Injector output 6 |
| A10 | Fuel pump output |
| A11 | Boost control PWM output |
| A12 | Ignition output 1 |
| A13 | Ignition output 2 |
| A14 | Ignition output 3 |
| A15 | Ignition output 4 |
| A16 | Ignition output 5 |
| A17 | Ignition output 6 |
| A18 | +5 V engine sensor supply |
| A19 | Throttle position input |
| A20 | Engine temperature input |
| A21 | Air temperature input |
| A22 | Sensor ground |
| A23 | Tachometer output |
| A24 | Thermofan output |
| A25 | RS232 RXD |
| A26 | Power ground |
| A27 | Power ground |
| A28 | Trigger reference signal |
| A29 | Trigger reference signal ground |
| A30 | Trigger sync signal |
| A31 | Oxygen sensor 1 signal |
| A32 | Oxygen sensor 1 signal ground |
| A33 | Oxygen sensor 1 pump output |
| A34 | RS232 TXD |
Connector B — 26 positions
| Pin | Function in 2013 Wolf diagram |
|---|---|
| B1 | Injector output 7 |
| B2 | Injector output 8 |
| B3 | Auxiliary low-side 1 |
| B4 | Auxiliary low-side 2 |
| B5 | Auxiliary low-side 3 |
| B6 | Auxiliary low-side 4 |
| B7 | Auxiliary low-side 5 |
| B8 | Ignition output 7 |
| B9 | Ignition output 8 |
| B10 | Auxiliary low-side 6 |
| B11 | Auxiliary low-side 7 |
| B12 | Auxiliary low-side 8 / turbo-timer option |
| B13 | Ignition power sense input |
| B14 | Auxiliary high/low-side 1 |
| B15 | Auxiliary high/low-side 2 |
| B16 | Auxiliary high/low-side 3 |
| B17 | Auxiliary high/low-side 4 |
| B18 | Auxiliary high/low-side 5 |
| B19 | Auxiliary high/low-side 6 |
| B20 | +5 V auxiliary output |
| B21 | MAP / MAF sensor input |
| B22 | +8 V auxiliary output |
| B23 | Oxygen sensor 2 signal |
| B24 | Ignition relay for stepper motor control |
| B25 | Source conflicting — see note |
| B26 | Not used in 2013 Wolf table; see note |