MSPNP-Pro E369395 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1993–1995 BMW E36 325i, 328i and M3 as listed in the manufacturer’s guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.
Application and installation
Confirm the actual engine and ECU connector, as the guide lists several models across the date range. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.
Pinout and documentation
AMP EFI E369395 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.
See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.
Rear options connectors by hardware version
These tables follow the AMP EFI application guide. The guide labels the 26- and 22-position tables V2 and separately illustrates a 20-position options connector. Identify the installed ECU and connector generation before wiring; these are rear options, not the complete original BMW main connector.
V2 connector 1 — 26 positions
| Pin | Function | Default or notes |
|---|---|---|
| 1A | Spark out A | Coil A, cylinder 1; logic-level smart coil |
| 1B | Spark out B | Coil B, cylinder 5; logic-level smart coil |
| 1C | Spark out C | Coil C, cylinder 3; logic-level smart coil |
| 1D | Spark out D | Coil D, cylinder 6; logic-level smart coil |
| 1E | Spark out E | Coil E, cylinder 2; logic-level smart coil |
| 1F | Spark out F | Coil F, cylinder 4; logic-level smart coil |
| 1G | Injector out G | — |
| 1H | Injector out H | — |
| 1I | Digital in 2 | — |
| 1J | Digital in 3 | — |
| 1K | Digital in 12 V | — |
| 1L | IAT | Aftermarket IAT; disconnect OE IAT if used |
| 1M | Digital frequency in 1 | — |
| 1N | Digital frequency in 2 | — |
| 1O | Analog in 1 | Assigned MAF; disconnect MAF to repurpose |
| 1P | Analog in 2 | General-purpose analog input |
| 1Q | Analog in 3 | General-purpose analog input |
| 1R | Analog in 4 | General-purpose analog input |
| 1S | Analog in 5 | General-purpose analog input |
| 1T | Analog in 6 | General-purpose analog input |
| 1U | Analog in 7 | General-purpose analog input |
| 1V | Analog in 8 / EGO | Wideband sensor input; can repurpose |
| 1W | CAN H | 120 ohm termination onboard |
| 1X | CAN L | 120 ohm termination onboard |
| 1Y | 5 V VREF out | Sensor 5 V power, internally fused 0.25 A |
| 1Z | Sensor ground | — |
V2 connector 2 — 22 positions
| Pin | Function | Default or notes |
|---|---|---|
| 2A | 12 V+ out | Ignition-switched; 0.25 A fuse; relay control only, not supply power |
| 2B | Digital input 1 / FLEX | Available flex sensor input |
| 2C | IAC1A | — |
| 2D | IAC1B | — |
| 2E | IAC2A | — |
| 2F | IAC2B | — |
| 2G | Injector out I | — |
| 2H | Injector out J | — |
| 2I | Tach out | Factory dashboard tachometer |
| 2J | High current out 1 | — |
| 2K | High current out 2 | — |
| 2L | High current out 3 | — |
| 2M | PWM out 2 | Idle valve; IAC close |
| 2N | PWM out 3 | VANOS camshaft control |
| 2O | PWM out 4 | — |
| 2P | PWM out 5 | — |
| 2Q | Unused | — |
| 2R | Unused | — |
| 2S | Unused | — |
| 2T | Unused | — |
| 2U | Unused | — |
| 2V | Unused | — |
20-position options connector
| Pin | Function | Default or notes |
|---|---|---|
| 1 | High current 1 | — |
| 2 | High current 2 | — |
| 3 | High current 3 | — |
| 4 | Injector G | High impedance only |
| 5 | Injector H | High impedance only |
| 6 | CMP+ | Hall only; internal pull-up to 5 V |
| 7 | Vref +5 V | — |
| 8 | External MAP | Move internal jumper |
| 9 | Analog input 1 | MAF |
| 10 | EGO | — |
| 11 | Digital input 4 | — |
| 12 | Digital input 2 | — |
| 13 | Digital input 1 | — |
| 14 | CANL | — |
| 15 | CANH | — |
| 16 | DFIN3 | Wheel speed 2, VR+ only |
| 17 | DFIN2 | Wheel speed 1, VR+ only |
| 18 | Analog input 2 | — |
| 19 | IAT | — |
| 20 | Sensor return | — |
The V2 source marks pins 1A–1F, 1W–1Z, 2A–2B and 2S–2V large and the remainder small. Check the original for views, electrical limits and jumper settings.