Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
MSPNP2
Applies to
MSPNP2
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer MSPNP2 product photograph used as a family illustration; vehicle-specific connectors and casing can differ. Image: AMP Engine Management; reproduced with permission.

MSPNP2 NJ8994 is a vehicle-specific MegaSquirt-II-based plug-in ECU. The manufacturer’s documentation lists 1989–1994 Nissan 240SX with SR20DET as listed in the manufacturer guide. Confirm the ECU part number, engine, harness, region and transmission before use.

Application and version

Match the engine and harness to the documented SR20DET application rather than a KA24 harness. This page describes the manufacturer’s version 2.0 documentation. Different hardware versions, optional jumpers and configurations can change installation details.

Installation and pinouts

Refer to the NJ8994 version 2.0 installation guide for its model-specific wiring diagrams, connector orientation, sensor configuration and setup instructions. Check the exact installed configuration; avoid applying the pinout of an MS3Pro PNP or another vehicle. The manufacturer’s manual index also links older version documents.

Select and verify the correct base tune, check timing as directed and tune the specific engine after installation.

Rear options connector — V2.0

The 26-way auxiliary connector table below is transcribed from the manufacturer's application guide. These are option-connector letters, not the main vehicle ECU connector. Check the source diagram for viewing orientation, jumper instructions, device configuration and current limits.

PinFunctionManufacturer noteAADC1Ensure no jumpers installed in JP12–JP15 ADC1 positionsBADC2Ensure no jumpers installed in JP12–JP15 ADC2 positionsCExternal MAPMove JP6 jumper to EXTDIAT inputECam inputVR input 2FOxygen sensor inputEGO sensor port = LocalGTable switch inputSee jumper matrix JP14HKnock inputSee jumper matrix JP12IFlexRequires JP11 installedJClutch inputSee jumper matrix JP13K5 V referenceMaximum 0.5 ALSignal groundMCAN lowNOutput 2Incompatible if Spark C is usedOCAN highPOutput 1Incompatible if Spark D is usedQTachometer outputRBoostSee boost control sectionSSpark DIncompatible if Output 1 is usedTInjector DUSpark CIncompatible if Output 2 is usedVInjector CWSpark BXInjector BYSpark AZInjector A

The source guide does not establish every numbered vehicle connector assignment here; the table must not be used as a substitute for an application-specific OEM connector schedule.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: MSPNP2 NJ8994 — Nissan 240SX SR20DET
MSPNP2 ECU product illustration
Manufacturer MSPNP2 product photograph used as a family illustration; vehicle-specific connectors and casing can differ. Image: AMP Engine Management; reproduced with permission.

MSPNP2 NJ8994 is a vehicle-specific MegaSquirt-II-based plug-in ECU. The manufacturer’s documentation lists 1989–1994 Nissan 240SX with SR20DET as listed in the manufacturer guide. Confirm the ECU part number, engine, harness, region and transmission before use.

Application and version

Match the engine and harness to the documented SR20DET application rather than a KA24 harness. This page describes the manufacturer’s version 2.0 documentation. Different hardware versions, optional jumpers and configurations can change installation details.

Installation and pinouts

Refer to the NJ8994 version 2.0 installation guide for its model-specific wiring diagrams, connector orientation, sensor configuration and setup instructions. Check the exact installed configuration; avoid applying the pinout of an MS3Pro PNP or another vehicle. The manufacturer’s manual index also links older version documents.

Select and verify the correct base tune, check timing as directed and tune the specific engine after installation.

Rear options connector — V2.0

The 26-way auxiliary connector table below is transcribed from the manufacturer's application guide. These are option-connector letters, not the main vehicle ECU connector. Check the source diagram for viewing orientation, jumper instructions, device configuration and current limits.

PinFunctionManufacturer note
AADC1Ensure no jumpers installed in JP12–JP15 ADC1 positions
BADC2Ensure no jumpers installed in JP12–JP15 ADC2 positions
CExternal MAPMove JP6 jumper to EXT
DIAT input
ECam inputVR input 2
FOxygen sensor inputEGO sensor port = Local
GTable switch inputSee jumper matrix JP14
HKnock inputSee jumper matrix JP12
IFlexRequires JP11 installed
JClutch inputSee jumper matrix JP13
K5 V referenceMaximum 0.5 A
LSignal ground
MCAN low
NOutput 2Incompatible if Spark C is used
OCAN high
POutput 1Incompatible if Spark D is used
QTachometer output
RBoostSee boost control section
SSpark DIncompatible if Output 1 is used
TInjector D
USpark CIncompatible if Output 2 is used
VInjector C
WSpark B
XInjector B
YSpark A
ZInjector A

The source guide does not establish every numbered vehicle connector assignment here; the table must not be used as a substitute for an application-specific OEM connector schedule.

Revision 3: MSPNP2 NJ8994 — Nissan 240SX SR20DET
MSPNP2 ECU product illustration
Manufacturer MSPNP2 product photograph used as a family illustration; vehicle-specific connectors and casing can differ. Image: AMP Engine Management; reproduced with permission.

MSPNP2 NJ8994 is a vehicle-specific MegaSquirt-II-based plug-in ECU. The manufacturer’s documentation lists 1989–1994 Nissan 240SX with SR20DET as listed in the manufacturer guide. Confirm the ECU part number, engine, harness, region and transmission before use.

Application and version

Match the engine and harness to the documented SR20DET application rather than a KA24 harness. This page describes the manufacturer’s version 2.0 documentation. Different hardware versions, optional jumpers and configurations can change installation details.

Installation and pinouts

Refer to the NJ8994 version 2.0 installation guide for its model-specific wiring diagrams, connector orientation, sensor configuration and setup instructions. Check the exact installed configuration; avoid applying the pinout of an MS3Pro PNP or another vehicle. The manufacturer’s manual index also links older version documents.

Select and verify the correct base tune, check timing as directed and tune the specific engine after installation.

Rear options connector — V2.0

The 26-way auxiliary connector table below is transcribed from the manufacturer's application guide. These are option-connector letters, not the main vehicle ECU connector. Check the source diagram for viewing orientation, jumper instructions, device configuration and current limits.

PinFunctionManufacturer note
AADC1Ensure no jumpers installed in JP12–JP15 ADC1 positions
BADC2Ensure no jumpers installed in JP12–JP15 ADC2 positions
CExternal MAPMove JP6 jumper to EXT
DIAT input
ECam inputVR input 2
FOxygen sensor inputEGO sensor port = Local
GTable switch inputSee jumper matrix JP14
HKnock inputSee jumper matrix JP12
IFlexRequires JP11 installed
JClutch inputSee jumper matrix JP13
K5 V referenceMaximum 0.5 A
LSignal ground
MCAN low
NOutput 2Incompatible if Spark C is used
OCAN high
POutput 1Incompatible if Spark D is used
QTachometer output
RBoostSee boost control section
SSpark DIncompatible if Output 1 is used
TInjector D
USpark CIncompatible if Output 2 is used
VInjector C
WSpark B
XInjector B
YSpark A
ZInjector A

The source guide does not establish every numbered vehicle connector assignment here; the table must not be used as a substitute for an application-specific OEM connector schedule.