Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Adaptronic standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 4
Removed text is struck through; added text is highlighted.
Adaptronic e440d is a standalone or earlier programmable engine-management system. Universal Select e440d wire-in controller. Haltech lists its own pinout and wiring diagrams and WARI software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e440d wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Connector pinoutA structured, redrawn pin-index reference for the 22-way and 26-way connectors is on Adaptronic e440d connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic pinout manual cited below.Further information
Adaptronic e440d model informationWiring, manuals or technical archiveAdaptronic manufacturer index
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are the universal ECU pin functions from the first three pages, not the factory harness function. The same manual documents additional Mazda NA6, NA8 and Familia wiring differences; follow the matching vehicle section and required harness changes. The universal table lists 2I and 2S as no connection, but later factory-application tables describe ignition output 3 or auxiliary output 3 at those positions. Treat this as a documentation inconsistency and confirm the exact hardware with the supplier. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are the universal ECU pin functions from the first three pages, not the factory harness function. The same manual documents additional Mazda NA6, NA8 and Familia wiring differences; follow the matching vehicle section and required harness changes. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.22-way connector
PinFunction1AConstant 12 V (source says not required)1BIgnition 12 V1CExternal 0–5 V analogue input1DAuxiliary output 21EAuxiliary output 61FIgnition output 31GIgnition output 11HIgnition output 21ISlave vehicle speed sensor 11JAuxiliary output 31KSlave vehicle speed sensor 21LAuxiliary output 71MMaster vehicle speed sensor 11NDigital input 71ODigital input 31PDigital input 11QDigital input 21RAuxiliary output 81SDigital input 41TIgnition output 41UDigital input 51VDigital input 6
26-way connector
PinFunction2APower ground2BPower ground2CSensor ground2DSensor ground2ECAS 1 input2FCAS 3 input2GCAS 2 input2HAuxiliary temperature2INo connection2JKnock2K5 V sensor supply2LDigital input 82MThrottle position signal2NOxygen / EGO input (0–1 V factory sensor; see source for wideband)2OMAP signal2PManifold air temperature2QEngine coolant temperature2RMaster vehicle speed sensor 22SNo connection2TAuxiliary output 52UInjector output 12VInjector output 42WAuxiliary output 12XAuxiliary output 42YInjector output 22ZInjector output 3
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Adaptronic e440d
Adaptronic e440d is a standalone or earlier programmable engine-management system. Universal Select e440d wire-in controller. Haltech lists its own pinout and wiring diagrams and WARI software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e440d wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are the universal ECU pin functions from the first three pages, not the factory harness function. The same manual documents additional Mazda NA6, NA8 and Familia wiring differences; follow the matching vehicle section and required harness changes. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.
22-way connector
| Pin | Function |
|---|
| 1A | Constant 12 V (source says not required) |
| 1B | Ignition 12 V |
| 1C | External 0–5 V analogue input |
| 1D | Auxiliary output 2 |
| 1E | Auxiliary output 6 |
| 1F | Ignition output 3 |
| 1G | Ignition output 1 |
| 1H | Ignition output 2 |
| 1I | Slave vehicle speed sensor 1 |
| 1J | Auxiliary output 3 |
| 1K | Slave vehicle speed sensor 2 |
| 1L | Auxiliary output 7 |
| 1M | Master vehicle speed sensor 1 |
| 1N | Digital input 7 |
| 1O | Digital input 3 |
| 1P | Digital input 1 |
| 1Q | Digital input 2 |
| 1R | Auxiliary output 8 |
| 1S | Digital input 4 |
| 1T | Ignition output 4 |
| 1U | Digital input 5 |
| 1V | Digital input 6 |
26-way connector
| Pin | Function |
|---|
| 2A | Power ground |
| 2B | Power ground |
| 2C | Sensor ground |
| 2D | Sensor ground |
| 2E | CAS 1 input |
| 2F | CAS 3 input |
| 2G | CAS 2 input |
| 2H | Auxiliary temperature |
| 2I | No connection |
| 2J | Knock |
| 2K | 5 V sensor supply |
| 2L | Digital input 8 |
| 2M | Throttle position signal |
| 2N | Oxygen / EGO input (0–1 V factory sensor; see source for wideband) |
| 2O | MAP signal |
| 2P | Manifold air temperature |
| 2Q | Engine coolant temperature |
| 2R | Master vehicle speed sensor 2 |
| 2S | No connection |
| 2T | Auxiliary output 5 |
| 2U | Injector output 1 |
| 2V | Injector output 4 |
| 2W | Auxiliary output 1 |
| 2X | Auxiliary output 4 |
| 2Y | Injector output 2 |
| 2Z | Injector output 3 |
Revision 4: Adaptronic e440d
Adaptronic e440d is a standalone or earlier programmable engine-management system. Universal Select e440d wire-in controller. Haltech lists its own pinout and wiring diagrams and WARI software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e440d wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Connector pinout
A structured, redrawn pin-index reference for the 22-way and 26-way connectors is on Adaptronic e440d connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic pinout manual cited below.
Further information
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are the universal ECU pin functions from the first three pages, not the factory harness function. The same manual documents additional Mazda NA6, NA8 and Familia wiring differences; follow the matching vehicle section and required harness changes. The universal table lists 2I and 2S as no connection, but later factory-application tables describe ignition output 3 or auxiliary output 3 at those positions. Treat this as a documentation inconsistency and confirm the exact hardware with the supplier. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.
22-way connector
| Pin | Function |
|---|
| 1A | Constant 12 V (source says not required) |
| 1B | Ignition 12 V |
| 1C | External 0–5 V analogue input |
| 1D | Auxiliary output 2 |
| 1E | Auxiliary output 6 |
| 1F | Ignition output 3 |
| 1G | Ignition output 1 |
| 1H | Ignition output 2 |
| 1I | Slave vehicle speed sensor 1 |
| 1J | Auxiliary output 3 |
| 1K | Slave vehicle speed sensor 2 |
| 1L | Auxiliary output 7 |
| 1M | Master vehicle speed sensor 1 |
| 1N | Digital input 7 |
| 1O | Digital input 3 |
| 1P | Digital input 1 |
| 1Q | Digital input 2 |
| 1R | Auxiliary output 8 |
| 1S | Digital input 4 |
| 1T | Ignition output 4 |
| 1U | Digital input 5 |
| 1V | Digital input 6 |
26-way connector
| Pin | Function |
|---|
| 2A | Power ground |
| 2B | Power ground |
| 2C | Sensor ground |
| 2D | Sensor ground |
| 2E | CAS 1 input |
| 2F | CAS 3 input |
| 2G | CAS 2 input |
| 2H | Auxiliary temperature |
| 2I | No connection |
| 2J | Knock |
| 2K | 5 V sensor supply |
| 2L | Digital input 8 |
| 2M | Throttle position signal |
| 2N | Oxygen / EGO input (0–1 V factory sensor; see source for wideband) |
| 2O | MAP signal |
| 2P | Manifold air temperature |
| 2Q | Engine coolant temperature |
| 2R | Master vehicle speed sensor 2 |
| 2S | No connection |
| 2T | Auxiliary output 5 |
| 2U | Injector output 1 |
| 2V | Injector output 4 |
| 2W | Auxiliary output 1 |
| 2X | Auxiliary output 4 |
| 2Y | Injector output 2 |
| 2Z | Injector output 3 |