Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- Adaptronic standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 3
Removed text is struck through; added text is highlighted.
Adaptronic e1280s is a standalone or earlier programmable engine-management system. Fully configurable e1280s wire-in controller. Haltech lists a distinct e1280s pinout, wiring diagram and Sekuku software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e1280s wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Connector pinoutA structured, redrawn pin-index reference for the 16-position high-current and 60-position main connectors is on Adaptronic e1280s connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic pinout guide cited below.Further information
Adaptronic e1280s model informationWiring, manuals or technical archiveAdaptronic manufacturer index
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are manufacturer default functions; several pins have software-selectable alternatives. Check the original guide for loom length, screen wire details and available options. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.
High-current connector (101–116)
PinFunction101Injector cylinder 1102Injector cylinder 2103Injector cylinder 3104Injector cylinder 4105Injector cylinder 5 / secondary injector cylinder 1106Injector cylinder 6 / secondary injector cylinder 2107Power ground108Power ground10912 V ignition-switch supply110Injector cylinder 7 / secondary injector cylinder 3111Injector cylinder 8 / secondary injector cylinder 4112Injector cylinder 9 / thermofan / VVT 3113Injector cylinder 10 / VVT 1114Injector cylinder 11 / purge / tachometer / VVT 4115Injector cylinder 12 / EGO heater / VVT 2116Power ground
Main connector (1–60)
PinFunction1Igniter cylinder 12Igniter cylinder 33Igniter cylinder 54Auxiliary 1: idle solenoid / stepper 1 / DBW 15Digital input 16Digital input 27Auxiliary 2: tachometer / stepper 38Digital input 39Auxiliary 3: A/C relay10Power ground11Igniter cylinder 212Igniter cylinder 413Igniter cylinder 614Igniter cylinder 715Igniter cylinder 816Auxiliary 4: stepper 2 / main relay17Analogue input 118Auxiliary 5: fuel pump19Digital input 420Power ground21Auxiliary 6: idle valve / stepper 4 / DBW 222Analogue input 223Knock input 124Knock input 225Auxiliary 8: boost control26Analogue input 627Analogue input 7: MAP28Analogue input 12: coolant temperature29Analogue input 13: EGO 130Sensor ground31Analogue input 332Auxiliary 7: check light / shift light33Vehicle speed sensor 334Analogue input 435Analogue input 536Analogue input 937Analogue input 1038Analogue input 839Vehicle speed sensor 440CAS 541CAS 142CAS 243Vehicle speed sensor 244Digital input 545Analogue input 1546Digital input 747Sensor ground485 V sensor supply49Digital input 850Power ground51CAS 352CAS 453Vehicle speed sensor 154Analogue input 11: air temperature55Analogue input 14: EGO 256Analogue input 16575 V sensor supply58Constant 12 V supply through fuse59Digital input 660Power ground
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Adaptronic e1280s
Adaptronic e1280s is a standalone or earlier programmable engine-management system. Fully configurable e1280s wire-in controller. Haltech lists a distinct e1280s pinout, wiring diagram and Sekuku software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e1280s wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are manufacturer default functions; several pins have software-selectable alternatives. Check the original guide for loom length, screen wire details and available options. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.
High-current connector (101–116)
| Pin | Function |
|---|
| 101 | Injector cylinder 1 |
| 102 | Injector cylinder 2 |
| 103 | Injector cylinder 3 |
| 104 | Injector cylinder 4 |
| 105 | Injector cylinder 5 / secondary injector cylinder 1 |
| 106 | Injector cylinder 6 / secondary injector cylinder 2 |
| 107 | Power ground |
| 108 | Power ground |
| 109 | 12 V ignition-switch supply |
| 110 | Injector cylinder 7 / secondary injector cylinder 3 |
| 111 | Injector cylinder 8 / secondary injector cylinder 4 |
| 112 | Injector cylinder 9 / thermofan / VVT 3 |
| 113 | Injector cylinder 10 / VVT 1 |
| 114 | Injector cylinder 11 / purge / tachometer / VVT 4 |
| 115 | Injector cylinder 12 / EGO heater / VVT 2 |
| 116 | Power ground |
Main connector (1–60)
| Pin | Function |
|---|
| 1 | Igniter cylinder 1 |
| 2 | Igniter cylinder 3 |
| 3 | Igniter cylinder 5 |
| 4 | Auxiliary 1: idle solenoid / stepper 1 / DBW 1 |
| 5 | Digital input 1 |
| 6 | Digital input 2 |
| 7 | Auxiliary 2: tachometer / stepper 3 |
| 8 | Digital input 3 |
| 9 | Auxiliary 3: A/C relay |
| 10 | Power ground |
| 11 | Igniter cylinder 2 |
| 12 | Igniter cylinder 4 |
| 13 | Igniter cylinder 6 |
| 14 | Igniter cylinder 7 |
| 15 | Igniter cylinder 8 |
| 16 | Auxiliary 4: stepper 2 / main relay |
| 17 | Analogue input 1 |
| 18 | Auxiliary 5: fuel pump |
| 19 | Digital input 4 |
| 20 | Power ground |
| 21 | Auxiliary 6: idle valve / stepper 4 / DBW 2 |
| 22 | Analogue input 2 |
| 23 | Knock input 1 |
| 24 | Knock input 2 |
| 25 | Auxiliary 8: boost control |
| 26 | Analogue input 6 |
| 27 | Analogue input 7: MAP |
| 28 | Analogue input 12: coolant temperature |
| 29 | Analogue input 13: EGO 1 |
| 30 | Sensor ground |
| 31 | Analogue input 3 |
| 32 | Auxiliary 7: check light / shift light |
| 33 | Vehicle speed sensor 3 |
| 34 | Analogue input 4 |
| 35 | Analogue input 5 |
| 36 | Analogue input 9 |
| 37 | Analogue input 10 |
| 38 | Analogue input 8 |
| 39 | Vehicle speed sensor 4 |
| 40 | CAS 5 |
| 41 | CAS 1 |
| 42 | CAS 2 |
| 43 | Vehicle speed sensor 2 |
| 44 | Digital input 5 |
| 45 | Analogue input 15 |
| 46 | Digital input 7 |
| 47 | Sensor ground |
| 48 | 5 V sensor supply |
| 49 | Digital input 8 |
| 50 | Power ground |
| 51 | CAS 3 |
| 52 | CAS 4 |
| 53 | Vehicle speed sensor 1 |
| 54 | Analogue input 11: air temperature |
| 55 | Analogue input 14: EGO 2 |
| 56 | Analogue input 16 |
| 57 | 5 V sensor supply |
| 58 | Constant 12 V supply through fuse |
| 59 | Digital input 6 |
| 60 | Power ground |
Revision 3: Adaptronic e1280s
Adaptronic e1280s is a standalone or earlier programmable engine-management system. Fully configurable e1280s wire-in controller. Haltech lists a distinct e1280s pinout, wiring diagram and Sekuku software. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the Adaptronic e1280s wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Connector pinout
A structured, redrawn pin-index reference for the 16-position high-current and 60-position main connectors is on Adaptronic e1280s connector pinout. Diagram redrawn by Tuning Wiki from the Adaptronic pinout guide cited below.
Further information
Manufacturer connector pinout
From the Adaptronic model-specific pinout guide, retained in Haltech's archive. These are manufacturer default functions; several pins have software-selectable alternatives. Check the original guide for loom length, screen wire details and available options. Confirm pin view, actual ECU revision, sensor grounding and current limits against the original.
High-current connector (101–116)
| Pin | Function |
|---|
| 101 | Injector cylinder 1 |
| 102 | Injector cylinder 2 |
| 103 | Injector cylinder 3 |
| 104 | Injector cylinder 4 |
| 105 | Injector cylinder 5 / secondary injector cylinder 1 |
| 106 | Injector cylinder 6 / secondary injector cylinder 2 |
| 107 | Power ground |
| 108 | Power ground |
| 109 | 12 V ignition-switch supply |
| 110 | Injector cylinder 7 / secondary injector cylinder 3 |
| 111 | Injector cylinder 8 / secondary injector cylinder 4 |
| 112 | Injector cylinder 9 / thermofan / VVT 3 |
| 113 | Injector cylinder 10 / VVT 1 |
| 114 | Injector cylinder 11 / purge / tachometer / VVT 4 |
| 115 | Injector cylinder 12 / EGO heater / VVT 2 |
| 116 | Power ground |
Main connector (1–60)
| Pin | Function |
|---|
| 1 | Igniter cylinder 1 |
| 2 | Igniter cylinder 3 |
| 3 | Igniter cylinder 5 |
| 4 | Auxiliary 1: idle solenoid / stepper 1 / DBW 1 |
| 5 | Digital input 1 |
| 6 | Digital input 2 |
| 7 | Auxiliary 2: tachometer / stepper 3 |
| 8 | Digital input 3 |
| 9 | Auxiliary 3: A/C relay |
| 10 | Power ground |
| 11 | Igniter cylinder 2 |
| 12 | Igniter cylinder 4 |
| 13 | Igniter cylinder 6 |
| 14 | Igniter cylinder 7 |
| 15 | Igniter cylinder 8 |
| 16 | Auxiliary 4: stepper 2 / main relay |
| 17 | Analogue input 1 |
| 18 | Auxiliary 5: fuel pump |
| 19 | Digital input 4 |
| 20 | Power ground |
| 21 | Auxiliary 6: idle valve / stepper 4 / DBW 2 |
| 22 | Analogue input 2 |
| 23 | Knock input 1 |
| 24 | Knock input 2 |
| 25 | Auxiliary 8: boost control |
| 26 | Analogue input 6 |
| 27 | Analogue input 7: MAP |
| 28 | Analogue input 12: coolant temperature |
| 29 | Analogue input 13: EGO 1 |
| 30 | Sensor ground |
| 31 | Analogue input 3 |
| 32 | Auxiliary 7: check light / shift light |
| 33 | Vehicle speed sensor 3 |
| 34 | Analogue input 4 |
| 35 | Analogue input 5 |
| 36 | Analogue input 9 |
| 37 | Analogue input 10 |
| 38 | Analogue input 8 |
| 39 | Vehicle speed sensor 4 |
| 40 | CAS 5 |
| 41 | CAS 1 |
| 42 | CAS 2 |
| 43 | Vehicle speed sensor 2 |
| 44 | Digital input 5 |
| 45 | Analogue input 15 |
| 46 | Digital input 7 |
| 47 | Sensor ground |
| 48 | 5 V sensor supply |
| 49 | Digital input 8 |
| 50 | Power ground |
| 51 | CAS 3 |
| 52 | CAS 4 |
| 53 | Vehicle speed sensor 1 |
| 54 | Analogue input 11: air temperature |
| 55 | Analogue input 14: EGO 2 |
| 56 | Analogue input 16 |
| 57 | 5 V sensor supply |
| 58 | Constant 12 V supply through fuse |
| 59 | Digital input 6 |
| 60 | Power ground |