Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
MS3Pro PNP
Applies to
MS3Pro PNP
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro MSM0405 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 2004–2005 Mazdaspeed Miata with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

This is the manufacturer’s specific Mazdaspeed application, distinct from ordinary MM0105. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MSM0405 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in sourceASensor ground—BKnock sensor 2—CAnalog input 2—DAnalog input 1MAFEIAT—FExternal MAP sensor—GCANL—H+5 V reference—ICANH—J+12 V ignitionMaximum 0.5 AKDigital frequency in 3—LDigital frequency in 2VSSMDigital in 2—NClutch signal—ODigital in 4—PPWM2—QHigh current 3NitrousRHigh current 2Boost controlSIgnition D logic level—TInjector HHigh Z or GPIO onlyUIgnition C logic level—VInjector GHigh Z or GPIO onlyWIgnition B logic level—XInjector FHigh Z or GPIO onlyYIgnition A logic level—ZInjector E—

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: MS3Pro PNP MSM0405 — Mazdaspeed Miata 2004–2005

MSPNP-Pro MSM0405 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 2004–2005 Mazdaspeed Miata with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

This is the manufacturer’s specific Mazdaspeed application, distinct from ordinary MM0105. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MSM0405 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in source
ASensor ground—
BKnock sensor 2—
CAnalog input 2—
DAnalog input 1MAF
EIAT—
FExternal MAP sensor—
GCANL—
H+5 V reference—
ICANH—
J+12 V ignitionMaximum 0.5 A
KDigital frequency in 3—
LDigital frequency in 2VSS
MDigital in 2—
NClutch signal—
ODigital in 4—
PPWM2—
QHigh current 3Nitrous
RHigh current 2Boost control
SIgnition D logic level—
TInjector HHigh Z or GPIO only
UIgnition C logic level—
VInjector GHigh Z or GPIO only
WIgnition B logic level—
XInjector FHigh Z or GPIO only
YIgnition A logic level—
ZInjector E—
Revision 3: MS3Pro PNP MSM0405 — Mazdaspeed Miata 2004–2005
AMP MSPNP-Pro Subaru WRX ECU
MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro MSM0405 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 2004–2005 Mazdaspeed Miata with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

This is the manufacturer’s specific Mazdaspeed application, distinct from ordinary MM0105. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MSM0405 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in source
ASensor ground—
BKnock sensor 2—
CAnalog input 2—
DAnalog input 1MAF
EIAT—
FExternal MAP sensor—
GCANL—
H+5 V reference—
ICANH—
J+12 V ignitionMaximum 0.5 A
KDigital frequency in 3—
LDigital frequency in 2VSS
MDigital in 2—
NClutch signal—
ODigital in 4—
PPWM2—
QHigh current 3Nitrous
RHigh current 2Boost control
SIgnition D logic level—
TInjector HHigh Z or GPIO only
UIgnition C logic level—
VInjector GHigh Z or GPIO only
WIgnition B logic level—
XInjector FHigh Z or GPIO only
YIgnition A logic level—
ZInjector E—