Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
MS3Pro PNP
Applies to
MS3Pro PNP
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro MM9093 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1990–1993 Mazda Miata 1.6L with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The guide directs removal of the ST SIGN fuse before running the ECU. Sequential injection requires wiring changes on 1990–1992 and 1993 federal cars; it identifies 1993 California cars separately. Read its instructions and diagrams. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MM9093 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in sourceASensor ground—BKnock sensor—CAnalog input 2—DAnalog input 1MAFEIAT—FExternal MAP sensor—GCANL—H+5 V reference—ICANH—J+12 V ignitionMaximum 0.5 AKDigital frequency in 3—LDigital frequency in 2VSSMDigital in 1FlexNDigital in 2Clutch signalODigital in 12 V (DI4)—PHigh current 1VVTQHigh current 3NitrousRHigh current 2Boost controlSIgnition D logic level—TInjector HHigh Z or GPIO onlyUIgnition C logic level—VInjector GHigh Z or GPIO onlyWIgnition B logic level—XInjector FHigh Z or GPIO onlyYIgnition A logic level—ZInjector EHigh Z or GPIO only

Vehicle and optional connector assignmentsTranscribed from this model's AMP EFI guide. Connector 1 and 4 are labelled factory wiring; connector 2 is optional wiring, and connector 3 is labelled optional wiring. “N/C” reproduces the guide's label, not an independent check of every vehicle harness; check the original diagram, connector orientation, jumpers and exact vehicle.Connector 1PinFunction from guide1AN/C1B+12 V ignition1CFuel pump relay (12 V)1DN/C1ECEL (via DFIN1)1FTach out1GCylinder 1/4 ignition coil (Ignition A out)1HCylinder 2/3 ignition coil (Ignition B out)1IN/C1JA/C relay (Injector J out)1KN/C1LFan 1 relay (PWM2)1MVSS (DFIN2)1NThrottle switch 5 V1ON/C1PN/C1QA/C switch in1RFan 1 relay (PWM2 via J6)1SN/C1TN/C1UN/C1VClutch switch (digital in 2)Connector 2PinFunction from guide2ACANH2BOxygen sensor2CCANL2DTach out2EExternal MAP sensor2FKnock sensor2GGround2HDigital in 1 (flex)2IPWM32JDigital in 12 V (DI4)2KAnalog in 22LHigh current 2 (boost)Connector 3PinFunction from guide3AIgnition C (cylinder 4 sequential)3BIgnition D (cylinder 2 sequential)3CIgnition A (cylinders 1/4 wasted spark, cylinder 1 sequential)3DIgnition B (cylinders 2/3 wasted spark, cylinder 3 sequential)3EInjector C (cylinder 4 sequential)3FInjector D (cylinder 2 sequential)3GInjector A (cylinders 1/4 batch, cylinder 1 sequential)3HInjector B (cylinders 2/3 batch, cylinder 3 sequential)3I+12 V out (relay supply)3JHigh current 1 (VVT)3KSensor ground3LIAC3MCKP (crank) signal3N+5 Vref3OCMP (cam) signal3PTPSConnector 4PinFunction from guide4AGround4BGround4CSensor ground4DSensor ground4ECKP (crank) signal4FSensor ground4GCMP (cam) signal4HN/C4IN/C4JN/C4K+5 Vref4LTPS4MN/C4NO2 sensor4OVAM output (external MAP)4PIAT sensor4QCLT sensor4RN/C4SCondenser fan (Injector I out)4TFuel pump relay (unused on 1990–1993)4UInjector A4VInjector B (Injector D — 1993 California emissions)4WIAC (PWM1)4XN/C4YN/C (Injector B — 1993 California emissions)4ZN/C (Injector C — 1993 California emissions)

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: MS3Pro PNP MM9093 — Mazda Miata 1990–1993

MSPNP-Pro MM9093 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1990–1993 Mazda Miata 1.6L with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The guide directs removal of the ST SIGN fuse before running the ECU. Sequential injection requires wiring changes on 1990–1992 and 1993 federal cars; it identifies 1993 California cars separately. Read its instructions and diagrams. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MM9093 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in source
ASensor ground—
BKnock sensor—
CAnalog input 2—
DAnalog input 1MAF
EIAT—
FExternal MAP sensor—
GCANL—
H+5 V reference—
ICANH—
J+12 V ignitionMaximum 0.5 A
KDigital frequency in 3—
LDigital frequency in 2VSS
MDigital in 1Flex
NDigital in 2Clutch signal
ODigital in 12 V (DI4)—
PHigh current 1VVT
QHigh current 3Nitrous
RHigh current 2Boost control
SIgnition D logic level—
TInjector HHigh Z or GPIO only
UIgnition C logic level—
VInjector GHigh Z or GPIO only
WIgnition B logic level—
XInjector FHigh Z or GPIO only
YIgnition A logic level—
ZInjector EHigh Z or GPIO only
Revision 4: MS3Pro PNP MM9093 — Mazda Miata 1990–1993
AMP MSPNP-Pro Subaru WRX ECU
MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro MM9093 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1990–1993 Mazda Miata 1.6L with manual transmission. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

The guide directs removal of the ST SIGN fuse before running the ECU. Sequential injection requires wiring changes on 1990–1992 and 1993 federal cars; it identifies 1993 California cars separately. Read its instructions and diagrams. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI MM9093 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connector — A–Z

From this model's AMP EFI installation guide. These are rear options connections; they do not constitute the full original vehicle ECU connector pinout. Check the manufacturer's connector orientation and configuration before wiring; functions marked as defaults are configurable.

PinFunctionDefault or note in source
ASensor ground—
BKnock sensor—
CAnalog input 2—
DAnalog input 1MAF
EIAT—
FExternal MAP sensor—
GCANL—
H+5 V reference—
ICANH—
J+12 V ignitionMaximum 0.5 A
KDigital frequency in 3—
LDigital frequency in 2VSS
MDigital in 1Flex
NDigital in 2Clutch signal
ODigital in 12 V (DI4)—
PHigh current 1VVT
QHigh current 3Nitrous
RHigh current 2Boost control
SIgnition D logic level—
TInjector HHigh Z or GPIO only
UIgnition C logic level—
VInjector GHigh Z or GPIO only
WIgnition B logic level—
XInjector FHigh Z or GPIO only
YIgnition A logic level—
ZInjector EHigh Z or GPIO only

Vehicle and optional connector assignments

Transcribed from this model's AMP EFI guide. Connector 1 and 4 are labelled factory wiring; connector 2 is optional wiring, and connector 3 is labelled optional wiring. “N/C” reproduces the guide's label, not an independent check of every vehicle harness; check the original diagram, connector orientation, jumpers and exact vehicle.

Connector 1

PinFunction from guide
1AN/C
1B+12 V ignition
1CFuel pump relay (12 V)
1DN/C
1ECEL (via DFIN1)
1FTach out
1GCylinder 1/4 ignition coil (Ignition A out)
1HCylinder 2/3 ignition coil (Ignition B out)
1IN/C
1JA/C relay (Injector J out)
1KN/C
1LFan 1 relay (PWM2)
1MVSS (DFIN2)
1NThrottle switch 5 V
1ON/C
1PN/C
1QA/C switch in
1RFan 1 relay (PWM2 via J6)
1SN/C
1TN/C
1UN/C
1VClutch switch (digital in 2)

Connector 2

PinFunction from guide
2ACANH
2BOxygen sensor
2CCANL
2DTach out
2EExternal MAP sensor
2FKnock sensor
2GGround
2HDigital in 1 (flex)
2IPWM3
2JDigital in 12 V (DI4)
2KAnalog in 2
2LHigh current 2 (boost)

Connector 3

PinFunction from guide
3AIgnition C (cylinder 4 sequential)
3BIgnition D (cylinder 2 sequential)
3CIgnition A (cylinders 1/4 wasted spark, cylinder 1 sequential)
3DIgnition B (cylinders 2/3 wasted spark, cylinder 3 sequential)
3EInjector C (cylinder 4 sequential)
3FInjector D (cylinder 2 sequential)
3GInjector A (cylinders 1/4 batch, cylinder 1 sequential)
3HInjector B (cylinders 2/3 batch, cylinder 3 sequential)
3I+12 V out (relay supply)
3JHigh current 1 (VVT)
3KSensor ground
3LIAC
3MCKP (crank) signal
3N+5 Vref
3OCMP (cam) signal
3PTPS

Connector 4

PinFunction from guide
4AGround
4BGround
4CSensor ground
4DSensor ground
4ECKP (crank) signal
4FSensor ground
4GCMP (cam) signal
4HN/C
4IN/C
4JN/C
4K+5 Vref
4LTPS
4MN/C
4NO2 sensor
4OVAM output (external MAP)
4PIAT sensor
4QCLT sensor
4RN/C
4SCondenser fan (Injector I out)
4TFuel pump relay (unused on 1990–1993)
4UInjector A
4VInjector B (Injector D — 1993 California emissions)
4WIAC (PWM1)
4XN/C
4YN/C (Injector B — 1993 California emissions)
4ZN/C (Injector C — 1993 California emissions)