Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MBE Systems standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
The MBE 967 belongs to the earlier serial ECU generation. SBD archives a model-specific connector pinout; a separate 967i ignition-only wiring instruction exists and should not be assumed identical. Source and identification.
Wiring and pinout
Model wiring documentation: MBE967 pinout information. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete documented 36-way connector
These positions come from the MBE 967e connection list dated 30 March 2000; the source specifically identifies 967e, so verify the exact build before using it for another 967 variant. Verify the connector view, programmable input/output configuration, coil driver type and electrical limits in the original.
PinDesignationSource note1FUEL TRIMMapping Plug 062WATER TEMPERATURE SIGNAL3AIR TEMPERATURE SIGNAL45V ANALOGUEMapping Plug 045ANALOGUE GROUNDMapping Plug 056POWER GROUNDMapping Plug 017POWER GROUND8POWER GROUND9POWER GROUND10FUEL PRESSURE INPUT/GEAR POSITION11CRANK RETURN12CRANK SIGNAL13ECU SUPPLY14SERIAL RECEIVEMapping Plug 0315FAULT LIGHT / SWITCH16SHIFT LIGHTSwitched Ground17FUEL PUMP RELAY DRIVESwitched Ground18IGNITION DRIVE 2Cylinders 2 + 3 Not used if distributor fitted19POWERSHIFT INPUTGround Active20THROTTLE SIGNAL21MAP SIGNAL (BOOST PRESSURE)225V ANALOGUE23ANALOGUE GROUND24ANALOGUE GROUND25OIL TEMPERATURE26IGNITION TRIMMapping Plug 0727OIL PRESSURE28BAROMETRIC PRESSURE SIGNAL / LAUNCH INPUT29LAMBDA SIGNAL30NOT USEDNot Used31NOT USEDNot Used32SERIAL TRANSMITMapping Plug 0233RADIATOR FAN RELAY DRIVESwitched Ground34TACHOMETER SIGNAL35INJECTOR OUTPUTAll Cylinders36IGNITION DRIVE 1Cylinders 1+ 4 Coil drive if distributor fitted
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MBE 967
The MBE 967 belongs to the earlier serial ECU generation. SBD archives a model-specific connector pinout; a separate 967i ignition-only wiring instruction exists and should not be assumed identical. Source and identification.
Wiring and pinout
Model wiring documentation: MBE967 pinout information. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete documented 36-way connector
These positions come from the MBE 967e connection list dated 30 March 2000; the source specifically identifies 967e, so verify the exact build before using it for another 967 variant. Verify the connector view, programmable input/output configuration, coil driver type and electrical limits in the original.
| Pin | Designation | Source note |
|---|
| 1 | FUEL TRIM | Mapping Plug 06 |
| 2 | WATER TEMPERATURE SIGNAL | |
| 3 | AIR TEMPERATURE SIGNAL | |
| 4 | 5V ANALOGUE | Mapping Plug 04 |
| 5 | ANALOGUE GROUND | Mapping Plug 05 |
| 6 | POWER GROUND | Mapping Plug 01 |
| 7 | POWER GROUND | |
| 8 | POWER GROUND | |
| 9 | POWER GROUND | |
| 10 | FUEL PRESSURE INPUT/GEAR POSITION | |
| 11 | CRANK RETURN | |
| 12 | CRANK SIGNAL | |
| 13 | ECU SUPPLY | |
| 14 | SERIAL RECEIVE | Mapping Plug 03 |
| 15 | FAULT LIGHT / SWITCH | |
| 16 | SHIFT LIGHT | Switched Ground |
| 17 | FUEL PUMP RELAY DRIVE | Switched Ground |
| 18 | IGNITION DRIVE 2 | Cylinders 2 + 3 Not used if distributor fitted |
| 19 | POWERSHIFT INPUT | Ground Active |
| 20 | THROTTLE SIGNAL | |
| 21 | MAP SIGNAL (BOOST PRESSURE) | |
| 22 | 5V ANALOGUE | |
| 23 | ANALOGUE GROUND | |
| 24 | ANALOGUE GROUND | |
| 25 | OIL TEMPERATURE | |
| 26 | IGNITION TRIM | Mapping Plug 07 |
| 27 | OIL PRESSURE | |
| 28 | BAROMETRIC PRESSURE SIGNAL / LAUNCH INPUT | |
| 29 | LAMBDA SIGNAL | |
| 30 | NOT USED | Not Used |
| 31 | NOT USED | Not Used |
| 32 | SERIAL TRANSMIT | Mapping Plug 02 |
| 33 | RADIATOR FAN RELAY DRIVE | Switched Ground |
| 34 | TACHOMETER SIGNAL | |
| 35 | INJECTOR OUTPUT | All Cylinders |
| 36 | IGNITION DRIVE 1 | Cylinders 1+ 4 Coil drive if distributor fitted |
Revision 2: MBE 967
The MBE 967 belongs to the earlier serial ECU generation. SBD archives a model-specific connector pinout; a separate 967i ignition-only wiring instruction exists and should not be assumed identical. Source and identification.
Wiring and pinout
Model wiring documentation: MBE967 pinout information. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete documented 36-way connector
These positions come from the MBE 967e connection list dated 30 March 2000; the source specifically identifies 967e, so verify the exact build before using it for another 967 variant. Verify the connector view, programmable input/output configuration, coil driver type and electrical limits in the original.
| Pin | Designation | Source note |
|---|
| 1 | FUEL TRIM | Mapping Plug 06 |
| 2 | WATER TEMPERATURE SIGNAL | |
| 3 | AIR TEMPERATURE SIGNAL | |
| 4 | 5V ANALOGUE | Mapping Plug 04 |
| 5 | ANALOGUE GROUND | Mapping Plug 05 |
| 6 | POWER GROUND | Mapping Plug 01 |
| 7 | POWER GROUND | |
| 8 | POWER GROUND | |
| 9 | POWER GROUND | |
| 10 | FUEL PRESSURE INPUT/GEAR POSITION | |
| 11 | CRANK RETURN | |
| 12 | CRANK SIGNAL | |
| 13 | ECU SUPPLY | |
| 14 | SERIAL RECEIVE | Mapping Plug 03 |
| 15 | FAULT LIGHT / SWITCH | |
| 16 | SHIFT LIGHT | Switched Ground |
| 17 | FUEL PUMP RELAY DRIVE | Switched Ground |
| 18 | IGNITION DRIVE 2 | Cylinders 2 + 3 Not used if distributor fitted |
| 19 | POWERSHIFT INPUT | Ground Active |
| 20 | THROTTLE SIGNAL | |
| 21 | MAP SIGNAL (BOOST PRESSURE) | |
| 22 | 5V ANALOGUE | |
| 23 | ANALOGUE GROUND | |
| 24 | ANALOGUE GROUND | |
| 25 | OIL TEMPERATURE | |
| 26 | IGNITION TRIM | Mapping Plug 07 |
| 27 | OIL PRESSURE | |
| 28 | BAROMETRIC PRESSURE SIGNAL / LAUNCH INPUT | |
| 29 | LAMBDA SIGNAL | |
| 30 | NOT USED | Not Used |
| 31 | NOT USED | Not Used |
| 32 | SERIAL TRANSMIT | Mapping Plug 02 |
| 33 | RADIATOR FAN RELAY DRIVE | Switched Ground |
| 34 | TACHOMETER SIGNAL | |
| 35 | INJECTOR OUTPUT | All Cylinders |
| 36 | IGNITION DRIVE 1 | Cylinders 1+ 4 Coil drive if distributor fitted |