Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MBE Systems standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 3 to revision 3
Removed text is struck through; added text is highlighted.
The 9A6 is a direct-injection ECU for four-cylinder engines; SBD developed its documented application for the Ford 1.6-litre EcoBoost. SBD also identifies twin CAN buses and wideband inputs. Direct-injector and throttle control depend on exact application and configuration. Source and identification.
Wiring and pinout
Model wiring documentation: 9A6 pinout issue F, not the 9A9 connector assignment. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete connector assignments
All 121 labelled positions follow the SBD 9A6 connection list, issue F, BOM 0.1, software f192 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.
PinManufacturer connection-list titleA001GroundA002GroundA003ECU Permanent 12V SupplyA00412V SwitchA00512V SwitchA006Air Charge Pump RelayA007Oil TempA008Injector A+A009Anti Lag SignalA010Baro SignalA0115Va2A012Injector A-A013Narrow Band Oxygen Sensor 1A0145Va1A015Lambda1 RA016Cam ReturnA017EGT SignalA018Air Temp SignalA019Not named in sourceA0200VaA021Malfunction Indicator Lamp (MIL)A022Wastegate DriveA023Rad Fan 1A024Fuel Pump RelayA025Shift Up SolenoidA026Launch SignalA027Injector C+A028Engine Oil PressureA029Lambda1 NA0305Va2A031Injector C-A032AC RequestA0335Va1A034HP Fuel SignalA035Cam SupplyA036Shift UpA037Start RequestA038TPS2 SignalA0390VaA040Electronic Wastegate Actuator Drive -A041Electronic Wastegate Actuator Drive +A042Lambda Sensor 2 HeaterA043Lambda Sensor 1 HeaterA044Shift Down SolenoidA045Pedal A SignalA046Injector B+A047TPS1 SignalA048Lambda1 VGA049Lambda1 PA050Injector B-A051Engine Stop SignalA0525Va1A053Gearbox SignalA054Cam 2SignalA055Pedal B SignalA056Not named in sourceA057Electronic Waste Gate (TPS4) SignalA0580VaA059Egas1 Motor Drive -A060Egas1 Motor Drive +A061HP Fuel Pump DriveA062Shift DownA063Rad Fan 1 RelayA064Air Accumulator PressureA065Injector D+A066MAPA067Water Temp SignalA068LP Fuel SignalA069Injector D-A070Boost LimitA0715Va1A072Neutral RequestA073Cam1 SignalA074Electronic Waste Gate (TPS3) SignalA075Clutch VoltageA076Nitrous Input PinA0770VaA078Engine Stop OutputA079Inlet Cam Drive (Cam 1)A080Exhaust Cam Drive (Cam 2)A081Tachometer DriveB082Upper Injector HB0835Va2B084WS3+B085Knock1 SignalB086WS1+B087MAF SignalB088CAN2 HB089CAN HB090Upper Injector GB0915Va2B092WS4+B093Knock1 ReturnB094WS2+B095PWM PedalB096CAN2 LB097CAN LB098Upper Injector FB0995Va1B100Crank SignalB101Knock 2 SignalB102WS1 ReturnB103WS2 ReturnB104WS3 ReturnB105WS4 ReturnB106Upper Injector EB1075Va1B108Crank ReturnB109Knock 2 ReturnB110Ignition Drive AB111Ignition Drive BB112Ignition Drive CB113Ignition Drive DB114HSD Battery +B115HSD Battery +B116Starter Solenoid DriveB117Ignition Output HSDB118PWM Water PumpB119n/cB120Fuel Pump HSDB121n/c
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: MBE 9A6
The 9A6 is a direct-injection ECU for four-cylinder engines; SBD developed its documented application for the Ford 1.6-litre EcoBoost. SBD also identifies twin CAN buses and wideband inputs. Direct-injector and throttle control depend on exact application and configuration. Source and identification.
Wiring and pinout
Model wiring documentation: 9A6 pinout issue F, not the 9A9 connector assignment. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete connector assignments
All 121 labelled positions follow the SBD 9A6 connection list, issue F, BOM 0.1, software f192 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.
| Pin | Manufacturer connection-list title |
|---|
| A001 | Ground |
| A002 | Ground |
| A003 | ECU Permanent 12V Supply |
| A004 | 12V Switch |
| A005 | 12V Switch |
| A006 | Air Charge Pump Relay |
| A007 | Oil Temp |
| A008 | Injector A+ |
| A009 | Anti Lag Signal |
| A010 | Baro Signal |
| A011 | 5Va2 |
| A012 | Injector A- |
| A013 | Narrow Band Oxygen Sensor 1 |
| A014 | 5Va1 |
| A015 | Lambda1 R |
| A016 | Cam Return |
| A017 | EGT Signal |
| A018 | Air Temp Signal |
| A019 | Not named in source |
| A020 | 0Va |
| A021 | Malfunction Indicator Lamp (MIL) |
| A022 | Wastegate Drive |
| A023 | Rad Fan 1 |
| A024 | Fuel Pump Relay |
| A025 | Shift Up Solenoid |
| A026 | Launch Signal |
| A027 | Injector C+ |
| A028 | Engine Oil Pressure |
| A029 | Lambda1 N |
| A030 | 5Va2 |
| A031 | Injector C- |
| A032 | AC Request |
| A033 | 5Va1 |
| A034 | HP Fuel Signal |
| A035 | Cam Supply |
| A036 | Shift Up |
| A037 | Start Request |
| A038 | TPS2 Signal |
| A039 | 0Va |
| A040 | Electronic Wastegate Actuator Drive - |
| A041 | Electronic Wastegate Actuator Drive + |
| A042 | Lambda Sensor 2 Heater |
| A043 | Lambda Sensor 1 Heater |
| A044 | Shift Down Solenoid |
| A045 | Pedal A Signal |
| A046 | Injector B+ |
| A047 | TPS1 Signal |
| A048 | Lambda1 VG |
| A049 | Lambda1 P |
| A050 | Injector B- |
| A051 | Engine Stop Signal |
| A052 | 5Va1 |
| A053 | Gearbox Signal |
| A054 | Cam 2Signal |
| A055 | Pedal B Signal |
| A056 | Not named in source |
| A057 | Electronic Waste Gate (TPS4) Signal |
| A058 | 0Va |
| A059 | Egas1 Motor Drive - |
| A060 | Egas1 Motor Drive + |
| A061 | HP Fuel Pump Drive |
| A062 | Shift Down |
| A063 | Rad Fan 1 Relay |
| A064 | Air Accumulator Pressure |
| A065 | Injector D+ |
| A066 | MAP |
| A067 | Water Temp Signal |
| A068 | LP Fuel Signal |
| A069 | Injector D- |
| A070 | Boost Limit |
| A071 | 5Va1 |
| A072 | Neutral Request |
| A073 | Cam1 Signal |
| A074 | Electronic Waste Gate (TPS3) Signal |
| A075 | Clutch Voltage |
| A076 | Nitrous Input Pin |
| A077 | 0Va |
| A078 | Engine Stop Output |
| A079 | Inlet Cam Drive (Cam 1) |
| A080 | Exhaust Cam Drive (Cam 2) |
| A081 | Tachometer Drive |
| B082 | Upper Injector H |
| B083 | 5Va2 |
| B084 | WS3+ |
| B085 | Knock1 Signal |
| B086 | WS1+ |
| B087 | MAF Signal |
| B088 | CAN2 H |
| B089 | CAN H |
| B090 | Upper Injector G |
| B091 | 5Va2 |
| B092 | WS4+ |
| B093 | Knock1 Return |
| B094 | WS2+ |
| B095 | PWM Pedal |
| B096 | CAN2 L |
| B097 | CAN L |
| B098 | Upper Injector F |
| B099 | 5Va1 |
| B100 | Crank Signal |
| B101 | Knock 2 Signal |
| B102 | WS1 Return |
| B103 | WS2 Return |
| B104 | WS3 Return |
| B105 | WS4 Return |
| B106 | Upper Injector E |
| B107 | 5Va1 |
| B108 | Crank Return |
| B109 | Knock 2 Return |
| B110 | Ignition Drive A |
| B111 | Ignition Drive B |
| B112 | Ignition Drive C |
| B113 | Ignition Drive D |
| B114 | HSD Battery + |
| B115 | HSD Battery + |
| B116 | Starter Solenoid Drive |
| B117 | Ignition Output HSD |
| B118 | PWM Water Pump |
| B119 | n/c |
| B120 | Fuel Pump HSD |
| B121 | n/c |
Revision 3: MBE 9A6
The 9A6 is a direct-injection ECU for four-cylinder engines; SBD developed its documented application for the Ford 1.6-litre EcoBoost. SBD also identifies twin CAN buses and wideband inputs. Direct-injector and throttle control depend on exact application and configuration. Source and identification.
Wiring and pinout
Model wiring documentation: 9A6 pinout issue F, not the 9A9 connector assignment. Check connector view, wiring harness, ECU part number and installed calibration before connecting power. Programmable input and output functions depend on the map and software.
Configuration and support
For programmable SBD-supplied ECUs, Easimap is used to inspect and change maps, subject to the interface and access of the actual ECU. Some vehicle-manufacturer supplied units are locked; SBD’s FAQ warns against attempting downloads to locked ECUs. Do not assume that a serial ECU map or harness transfers directly to a newer CAN unit.
Evidence limits
Verify the build, trigger inputs, coil-driver type and software with the supplier. Not all historic variants and pin assignments are documented here.
Complete connector assignments
All 121 labelled positions follow the SBD 9A6 connection list, issue F, BOM 0.1, software f192 onward. The table reproduces the source's pin titles; “not named” indicates an empty title, not necessarily an unused circuit. Consult the original for output ratings, pull-ups, individual notes and connector orientation. Assigned functions depend on calibration and particular hardware.
| Pin | Manufacturer connection-list title |
|---|
| A001 | Ground |
| A002 | Ground |
| A003 | ECU Permanent 12V Supply |
| A004 | 12V Switch |
| A005 | 12V Switch |
| A006 | Air Charge Pump Relay |
| A007 | Oil Temp |
| A008 | Injector A+ |
| A009 | Anti Lag Signal |
| A010 | Baro Signal |
| A011 | 5Va2 |
| A012 | Injector A- |
| A013 | Narrow Band Oxygen Sensor 1 |
| A014 | 5Va1 |
| A015 | Lambda1 R |
| A016 | Cam Return |
| A017 | EGT Signal |
| A018 | Air Temp Signal |
| A019 | Not named in source |
| A020 | 0Va |
| A021 | Malfunction Indicator Lamp (MIL) |
| A022 | Wastegate Drive |
| A023 | Rad Fan 1 |
| A024 | Fuel Pump Relay |
| A025 | Shift Up Solenoid |
| A026 | Launch Signal |
| A027 | Injector C+ |
| A028 | Engine Oil Pressure |
| A029 | Lambda1 N |
| A030 | 5Va2 |
| A031 | Injector C- |
| A032 | AC Request |
| A033 | 5Va1 |
| A034 | HP Fuel Signal |
| A035 | Cam Supply |
| A036 | Shift Up |
| A037 | Start Request |
| A038 | TPS2 Signal |
| A039 | 0Va |
| A040 | Electronic Wastegate Actuator Drive - |
| A041 | Electronic Wastegate Actuator Drive + |
| A042 | Lambda Sensor 2 Heater |
| A043 | Lambda Sensor 1 Heater |
| A044 | Shift Down Solenoid |
| A045 | Pedal A Signal |
| A046 | Injector B+ |
| A047 | TPS1 Signal |
| A048 | Lambda1 VG |
| A049 | Lambda1 P |
| A050 | Injector B- |
| A051 | Engine Stop Signal |
| A052 | 5Va1 |
| A053 | Gearbox Signal |
| A054 | Cam 2Signal |
| A055 | Pedal B Signal |
| A056 | Not named in source |
| A057 | Electronic Waste Gate (TPS4) Signal |
| A058 | 0Va |
| A059 | Egas1 Motor Drive - |
| A060 | Egas1 Motor Drive + |
| A061 | HP Fuel Pump Drive |
| A062 | Shift Down |
| A063 | Rad Fan 1 Relay |
| A064 | Air Accumulator Pressure |
| A065 | Injector D+ |
| A066 | MAP |
| A067 | Water Temp Signal |
| A068 | LP Fuel Signal |
| A069 | Injector D- |
| A070 | Boost Limit |
| A071 | 5Va1 |
| A072 | Neutral Request |
| A073 | Cam1 Signal |
| A074 | Electronic Waste Gate (TPS3) Signal |
| A075 | Clutch Voltage |
| A076 | Nitrous Input Pin |
| A077 | 0Va |
| A078 | Engine Stop Output |
| A079 | Inlet Cam Drive (Cam 1) |
| A080 | Exhaust Cam Drive (Cam 2) |
| A081 | Tachometer Drive |
| B082 | Upper Injector H |
| B083 | 5Va2 |
| B084 | WS3+ |
| B085 | Knock1 Signal |
| B086 | WS1+ |
| B087 | MAF Signal |
| B088 | CAN2 H |
| B089 | CAN H |
| B090 | Upper Injector G |
| B091 | 5Va2 |
| B092 | WS4+ |
| B093 | Knock1 Return |
| B094 | WS2+ |
| B095 | PWM Pedal |
| B096 | CAN2 L |
| B097 | CAN L |
| B098 | Upper Injector F |
| B099 | 5Va1 |
| B100 | Crank Signal |
| B101 | Knock 2 Signal |
| B102 | WS1 Return |
| B103 | WS2 Return |
| B104 | WS3 Return |
| B105 | WS4 Return |
| B106 | Upper Injector E |
| B107 | 5Va1 |
| B108 | Crank Return |
| B109 | Knock 2 Return |
| B110 | Ignition Drive A |
| B111 | Ignition Drive B |
| B112 | Ignition Drive C |
| B113 | Ignition Drive D |
| B114 | HSD Battery + |
| B115 | HSD Battery + |
| B116 | Starter Solenoid Drive |
| B117 | Ignition Output HSD |
| B118 | PWM Water Pump |
| B119 | n/c |
| B120 | Fuel Pump HSD |
| B121 | n/c |