Removed text is struck through; added text is highlighted.
Haltech Elite 750 (HT-150600) product photograph: Haltech product image library; reproduced with permission.
Haltech Elite 750 is a programmable engine-management ECU in Haltech's Elite family. Six injector and six ignition outputs, 2 analogue voltage inputs and no half-bridge outputs in Haltech's comparison. Haltech universal comparison.
Identification and I/O
ItemManufacturer comparisonInjector channels6, peak-and-holdIgnition channels6Digital pulsed outputs5MAP sensor4 bar internalTuning softwareESP for Elite firmware 2.xx; NSP for Elite firmware 3.xx; verify installed firmware
Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.
Pinout and wiring
Use the manufacturer wiring diagrams and select the Elite 750 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.
Software and further information
Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.
34-way connector pinout
Transcribed from the Haltech Elite 750 complete pinout. Manufacturer wire-colour abbreviations are retained; a dash means no function is shown in the source. The * symbol identifies the manufacturer's default allocation, which may be configurable. Use the original diagram for connector orientation and electrical limits.
Open each version to inspect formatting, tables and photographs.
Revision 3: Haltech Elite 750Haltech Elite 750 (HT-150600) product photograph: Haltech product image library; reproduced with permission.
Haltech Elite 750 is a programmable engine-management ECU in Haltech's Elite family. Six injector and six ignition outputs, 2 analogue voltage inputs and no half-bridge outputs in Haltech's comparison. Haltech universal comparison.
Identification and I/O
Item
Manufacturer comparison
Injector channels
6, peak-and-hold
Ignition channels
6
Digital pulsed outputs
5
MAP sensor
4 bar internal
Tuning software
ESP for Elite firmware 2.xx; NSP for Elite firmware 3.xx; verify installed firmware
Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.
Pinout and wiring
Use the manufacturer wiring diagrams and select the Elite 750 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.
Software and further information
Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.
34-way connector pinout
Transcribed from the Haltech Elite 750 complete pinout. Manufacturer wire-colour abbreviations are retained; a dash means no function is shown in the source. The * symbol identifies the manufacturer's default allocation, which may be configurable. Use the original diagram for connector orientation and electrical limits.
Pin
Wire colour code
Function
1
V/BR
DPO 2
2
GY/Y <SHD>
AVI 1 (* O2 Sensor)
3
Y/B
IGN 1
4
Y/R
IGN 2
5
Y/O
IGN 3
6
Y/G
IGN 4
7
Y/BR
IGN 5
8
Y/L
IGN 6
9
O
+5V DC
10
B
BATTERY GROUND
11
B/W
SIGNAL GROUND
12
GY <SHD>
DPI 1
13
GY/B <SHD>
DPI 2
14
W
THROTTLE POSITION SENSOR
15
Y
AVI 3 (* MAP )
16
W
CAN H
17
L
CAN L
18
V/B
DPO 1
19
L
INJ 1
20
L/B
INJ 2
21
L/BR
INJ 3
22
L/R
INJ 4
23
V/R
DPO 3
24
B/Y
DPO 5 (* Fuel Pump Relay)
25
V/O
DPO 4
26
R/L
+13.8V ECU / INJECTOR PWR
27
L/O
INJ 5
28
L/Y
INJ 6
29
GY
AIR TEMPERATURE
30
V
COOLANT TEMPERATURE
31
Y (GY 4C)
TRIGGER +
32
Y (GY/B 4C)
HOME +
33
G (GY 4C)
TRIGGER -
34
G (GY/B 4C)
HOME -
Revision 3: Haltech Elite 750Haltech Elite 750 (HT-150600) product photograph: Haltech product image library; reproduced with permission.
Haltech Elite 750 is a programmable engine-management ECU in Haltech's Elite family. Six injector and six ignition outputs, 2 analogue voltage inputs and no half-bridge outputs in Haltech's comparison. Haltech universal comparison.
Identification and I/O
Item
Manufacturer comparison
Injector channels
6, peak-and-hold
Ignition channels
6
Digital pulsed outputs
5
MAP sensor
4 bar internal
Tuning software
ESP for Elite firmware 2.xx; NSP for Elite firmware 3.xx; verify installed firmware
Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.
Pinout and wiring
Use the manufacturer wiring diagrams and select the Elite 750 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.
Software and further information
Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.
34-way connector pinout
Transcribed from the Haltech Elite 750 complete pinout. Manufacturer wire-colour abbreviations are retained; a dash means no function is shown in the source. The * symbol identifies the manufacturer's default allocation, which may be configurable. Use the original diagram for connector orientation and electrical limits.