Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Speeduino standalone ECUs
Applies to
Speeduino standalone ECUs
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Speeduino v0.2 PVT PCB design drawing by Josh Stewart. Source: Speeduino hardware repository; distributed under the repository's CERN-OHL-S licence.

The second shield develops the v0.1. Its documented design features include four high-impedance injector channels, four ignition outputs for igniters or logic-level coils, coolant, air-temperature, oxygen and throttle inputs, optional MAP sensor and speed-sensing inputs. The historical document records a testing status in September 2014; this is not a statement of present availability.

Connections and setup

The v0.2 project description, layout and jumper setup describes screw-terminal I/O and an optional VR conditioner. JP1 selects 5 V or 12 V logic output; neither setting permits direct high-current coil drive.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.

v0.2 PVT board terminal labels

The Speeduino project v0.2 board drawing is identified as a work-in-progress PVT snapshot. The following terminal labels and their physical order are as drawn; the position numbers below are descriptive, not manufacturer connector cavity numbers. Verify against the actual board, revision and jumper settings.

J1 sensor and trigger (left to right)

Position in drawingBoard label1IAT2IAT Ret3CLT4CLT Ret5TPS6TPS Ret7Vref8O29GND10Vref11VR1−12RPM113VR2−14RPM2

J2 injectors (top to bottom)

Position in drawingBoard label1INJ12INJ23INJ34INJ4

J3 power (top to bottom)

Position in drawingBoard label112 V2GND

J4 ignition (top to bottom)

Position in drawingBoard label1IGN12IGN23IGN34IGN4

J5 spare outputs (top to bottom)

Position in drawingBoard label1S42S33S24S1

Ignition pins are for an igniter or logic-level coils, not direct high-current coil drive. The project v0.2 notes describe the optional VR conditioner and trigger jumpers.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Speeduino v0.2
Speeduino v0.2 PVT PCB design drawing
Speeduino v0.2 PVT PCB design drawing by Josh Stewart. Source: Speeduino hardware repository; distributed under the repository's CERN-OHL-S licence.

The second shield develops the v0.1. Its documented design features include four high-impedance injector channels, four ignition outputs for igniters or logic-level coils, coolant, air-temperature, oxygen and throttle inputs, optional MAP sensor and speed-sensing inputs. The historical document records a testing status in September 2014; this is not a statement of present availability.

Connections and setup

The v0.2 project description, layout and jumper setup describes screw-terminal I/O and an optional VR conditioner. JP1 selects 5 V or 12 V logic output; neither setting permits direct high-current coil drive.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.

v0.2 PVT board terminal labels

The Speeduino project v0.2 board drawing is identified as a work-in-progress PVT snapshot. The following terminal labels and their physical order are as drawn; the position numbers below are descriptive, not manufacturer connector cavity numbers. Verify against the actual board, revision and jumper settings.

J1 sensor and trigger (left to right)

Position in drawingBoard label
1IAT
2IAT Ret
3CLT
4CLT Ret
5TPS
6TPS Ret
7Vref
8O2
9GND
10Vref
11VR1−
12RPM1
13VR2−
14RPM2

J2 injectors (top to bottom)

Position in drawingBoard label
1INJ1
2INJ2
3INJ3
4INJ4

J3 power (top to bottom)

Position in drawingBoard label
112 V
2GND

J4 ignition (top to bottom)

Position in drawingBoard label
1IGN1
2IGN2
3IGN3
4IGN4

J5 spare outputs (top to bottom)

Position in drawingBoard label
1S4
2S3
3S2
4S1

Ignition pins are for an igniter or logic-level coils, not direct high-current coil drive. The project v0.2 notes describe the optional VR conditioner and trigger jumpers.

Revision 3: Speeduino v0.2
Speeduino v0.2 PVT PCB design drawing
Speeduino v0.2 PVT PCB design drawing by Josh Stewart. Source: Speeduino hardware repository; distributed under the repository's CERN-OHL-S licence.

The second shield develops the v0.1. Its documented design features include four high-impedance injector channels, four ignition outputs for igniters or logic-level coils, coolant, air-temperature, oxygen and throttle inputs, optional MAP sensor and speed-sensing inputs. The historical document records a testing status in September 2014; this is not a statement of present availability.

Connections and setup

The v0.2 project description, layout and jumper setup describes screw-terminal I/O and an optional VR conditioner. JP1 selects 5 V or 12 V logic output; neither setting permits direct high-current coil drive.

Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.

v0.2 PVT board terminal labels

The Speeduino project v0.2 board drawing is identified as a work-in-progress PVT snapshot. The following terminal labels and their physical order are as drawn; the position numbers below are descriptive, not manufacturer connector cavity numbers. Verify against the actual board, revision and jumper settings.

J1 sensor and trigger (left to right)

Position in drawingBoard label
1IAT
2IAT Ret
3CLT
4CLT Ret
5TPS
6TPS Ret
7Vref
8O2
9GND
10Vref
11VR1−
12RPM1
13VR2−
14RPM2

J2 injectors (top to bottom)

Position in drawingBoard label
1INJ1
2INJ2
3INJ3
4INJ4

J3 power (top to bottom)

Position in drawingBoard label
112 V
2GND

J4 ignition (top to bottom)

Position in drawingBoard label
1IGN1
2IGN2
3IGN3
4IGN4

J5 spare outputs (top to bottom)

Position in drawingBoard label
1S4
2S3
3S2
4S1

Ignition pins are for an igniter or logic-level coils, not direct high-current coil drive. The project v0.2 notes describe the optional VR conditioner and trigger jumpers.