
MS3Pro Ultimate is a MegaSquirt-family engine-management product. The earlier high-feature MS3Pro Ultimate is listed as discontinued. Its manual describes 10 peak-and-hold or high-impedance injector outputs and eight logic-level spark outputs. Model source.
Identification and software
Record the ECU label, processor generation, board revision, firmware and installed hardware modifications. Calibration software and firmware must match the hardware. DIYAutoTune software and firmware · Model-specific information.
Wiring and pinout
Use the matching model document and wiring or support reference; the manufacturer manual index distinguishes wire-in and vehicle-specific variants. Check connector orientation, wiring changes, fuse ratings and output configuration before connecting loads; matching cases or software families do not establish identical pin functions.
ECU connector pin assignments
These tables reproduce the functions in the AMP EFI 1.210, firmware 1.5.2 (2021) manual. Check the manual's connector view, harness colours, grounding and current limits against the actual ECU and firmware. Do not substitute the pinout of another MS3Pro generation: for example, the EVO and Ultimate manuals assign white connector positions 13 and 16 differently.
White, 35 way
| Pin | Function in source |
|---|---|
| 1 | High current out 1 |
| 2 | High current out 2 |
| 3 | Injector out J |
| 4 | Injector out I |
| 5 | High current out 3 |
| 6 | CKP+ |
| 7 | Knock In 2 |
| 8 | 5V+ VREF out 1 |
| 9 | TPS in |
| 10 | MAT in |
| 11 | CLT in |
| 12 | Analog In 6 |
| 13 | Power ground |
| 14 | PWM / Idle Out 1 |
| 15 | CKP- |
| 16 | Logic ground * |
| 17 | Analog In 7 |
| 18 | Sensor return |
| 19 | Analog in 1 |
| 20 | Analog in 2 |
| 21 | Analog in 3 |
| 22 | Analog In 4 |
| 23 | Analog In 5 |
| 24 | Tach out |
| 25 | O2 in |
| 26 | CMP+ |
| 27 | CMP- |
| 28 | Fuel pump relay out |
| 29 | PWM out 2 |
| 30 | PWM out 3 |
| 31 | Knock in 1 |
| 32 | Digital switched in 1 |
| 33 | CAN L |
| 34 | CAN H |
| 35 | 12V+ switched power in |
Gray, 35 way
| Pin | Function in source |
|---|---|
| 1 | Injector out A |
| 2 | Injector out B |
| 3 | Ground |
| 4 | Injector out C |
| 5 | Ground |
| 6 | Injector out D |
| 7 | Ground |
| 8 | Injector out E |
| 9 | Ground |
| 10 | Injector out F |
| 11 | Injector out G |
| 12 | Injector out H |
| 13 | Spark out G |
| 14 | Spark out E |
| 15 | Spark out C |
| 16 | Spark out H |
| 17 | Digital frequency in 2 |
| 18 | Ground |
| 19 | Digital switched 12V in |
| 20 | Digital switched in 2 |
| 21 | Digital frequency in 3 |
| 22 | Digital Frequency in 3 VR+ |
| 23 | Digital Frequency In 3 VR- |
| 24 | Spark out F |
| 25 | Spark out B |
| 26 | Spark out D |
| 27 | Spark out A |
| 28 | Digital frequency in 1 |
| 29 | Digital switched in 3 |
| 30 | Stepper IAC out 1B |
| 31 | Stepper IAC out 1A |
| 32 | Stepper IAC out 2A |
| 33 | Stepper IAC out 2B |
| 34 | Digital Frequency in 1 VR+ |
| 35 | Digital Frequency in 1 VR- |
Black, 23 way
| Pin | Function in source |
|---|---|
| 1 | PWM out 5 |
| 2 | PWM out 4 |
| 3 | Digital out 2 |
| 4 | Digital out 1 |
| 5 | Digital I/O 4 |
| 6 | Digital I/O 2 |
| 7 | Analog in 8 |
| 8 | 5V+ VREF out 2 |
| 9 | Fuel only coil negative |
| 10 | Digital switched in 5 |
| 11 | Digital switched in 4 |
| 12 | Digital I/O 5 |
| 13 | Digital I/O 3 |
| 14 | Digital I/O 1 |
| 15 | 5V+ VREF out 2 |
| 16 | Fuel only battery 12V+ |
| 17 | Sensor return |
| 18 | Sensor return |
| 19 | Sensor return |
| 20 | Sensor return |
| 21 | Sensor return |
| 22 | 5V+ VREF out 1 |
| 23 | Keep alive power |
M12 serial service connector
The source lists M12 pins 1, 2, 3 and 4 to DB9 pins 9 (5 V reference), 3 (data), 5 (ground) and 2 (data), respectively. Verify the connector pin markings and use the matching adapter.
See the MegaSquirt and MS3Pro family guide. Sources reviewed 17 November 2026.