Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
FuelTech standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

FT400 product image from the FuelTech manufacturer manual, page 5; reproduced with permission.

FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.

Identification and software

Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.

Wiring and pinout

Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.

See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.

24-way main harness connector

Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.

PinFunction1Tachometer output (green)2Auxiliary output #3 (yellow 3)3Input 1 — intake air temperature (white/blue)4Auxiliary output #2 (yellow 2)5Input 2 — configurable sensor (white)6Auxiliary output #1 (yellow 1)7Input 3 — coolant temperature (pink)8Auxiliary output #4 (yellow 4)9Input 4 — configurable sensor (blue)10Ignition output E (gray E)11TPS signal / TPS 1 on electronic throttle (orange)12Ignition output D (gray D)13MAP signal output (yellow/red)14Ignition output C (gray C)15Camshaft position sensor input (green/yellow)16Ignition output B (gray B)17RPM signal input (shielded cable)18Ignition output A (gray A)19Battery negative / signal ground (black)205 V sensor supply (green/red)21Switched 12 V supply (red)22Power ground (black/white)23Fuel injector bank B negative (brown)24Fuel injector bank A negative (purple)

FT400 16-way auxiliary connector

Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.

PinFunction1O2 sensor input2Ignition output F3Electronic throttle TPS 24Auxiliary output #7 (yellow #7)5Two-step input6Yellow #6 auxiliary output — table calls it #7; see note7A/C button input8Yellow #5 auxiliary output — table calls it #7; see note9Power ground10Pedal signal #111Throttle or pedal sensor ground output12Pedal signal #213Electronic throttle motor #1 / step motor coil #114Electronic throttle motor #2 / step motor coil #215Electronic throttle motor #1 / step motor coil #116Electronic throttle motor #2 / step motor coil #2

Structured pinoutA structured pin index and redrawn connector diagrams are in FuelTech FT350 and FT400 connector pinout. It covers the shared 24-way main connector and the FT400's 16-way auxiliary connector.Supported configurationsFuelTech's FT350 / FT400 manual (section 4, manufacturer specification) lists support for 1, 2, 3, 4, 5, 6, 8, 10 and 12-cylinder engines up to 16,000 rpm, with a built-in 7 bar (100 psi) MAP sensor and a 4.3-inch colour touch screen. Ignition is controlled from a crankshaft trigger wheel or a distributor. Fuel is delivered through two independent injector banks controlling up to twelve injectors, or more with a peak-and-hold module. The FT400 adds electronic pedal and throttle control, closed-loop lambda control, automatic fuel-map adjustment and seven auxiliary outputs. The FT350 has four auxiliary outputs and four configurable sensor inputs. The listed working temperature range is −10 °C to 60 °C. FuelTech FT350 / FT400 manual, accessed 19 November 2026.Not establishedThe microcontroller used in the FT350 and FT400 is not named in FuelTech's published documentation.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: FuelTech FT400

FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.

Identification and software

Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.

Wiring and pinout

Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.

See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.

24-way main harness connector

Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.

PinFunction
1Tachometer output (green)
2Auxiliary output #3 (yellow 3)
3Input 1 — intake air temperature (white/blue)
4Auxiliary output #2 (yellow 2)
5Input 2 — configurable sensor (white)
6Auxiliary output #1 (yellow 1)
7Input 3 — coolant temperature (pink)
8Auxiliary output #4 (yellow 4)
9Input 4 — configurable sensor (blue)
10Ignition output E (gray E)
11TPS signal / TPS 1 on electronic throttle (orange)
12Ignition output D (gray D)
13MAP signal output (yellow/red)
14Ignition output C (gray C)
15Camshaft position sensor input (green/yellow)
16Ignition output B (gray B)
17RPM signal input (shielded cable)
18Ignition output A (gray A)
19Battery negative / signal ground (black)
205 V sensor supply (green/red)
21Switched 12 V supply (red)
22Power ground (black/white)
23Fuel injector bank B negative (brown)
24Fuel injector bank A negative (purple)

FT400 16-way auxiliary connector

Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.

PinFunction
1O2 sensor input
2Ignition output F
3Electronic throttle TPS 2
4Auxiliary output #7 (yellow #7)
5Two-step input
6Yellow #6 auxiliary output — table calls it #7; see note
7A/C button input
8Yellow #5 auxiliary output — table calls it #7; see note
9Power ground
10Pedal signal #1
11Throttle or pedal sensor ground output
12Pedal signal #2
13Electronic throttle motor #1 / step motor coil #1
14Electronic throttle motor #2 / step motor coil #2
15Electronic throttle motor #1 / step motor coil #1
16Electronic throttle motor #2 / step motor coil #2
Revision 4: FuelTech FT400
FT400 ECU
FT400 product image from the FuelTech manufacturer manual, page 5; reproduced with permission.

FuelTech FT400 is a Earlier FT generation engine-management unit. Early colour-touchscreen ECU with two injection banks, seven auxiliary outputs and electronic-throttle support, according to the shared manual. FuelTech model documentation · FuelTech range comparison.

Identification and software

Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: ECU Manager / Datalogger. FuelTech software and compatibility.

Wiring and pinout

Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.

See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.

24-way main harness connector

Functions are from the FuelTech FT350 / FT400 manual, version 2.0, section 5.1. The source shows the rear of the harness connector. Inputs 2 and 4 have variant-specific recommended applications; check the model and configuration. Ground requirements in this manual differ from other FT generations.

PinFunction
1Tachometer output (green)
2Auxiliary output #3 (yellow 3)
3Input 1 — intake air temperature (white/blue)
4Auxiliary output #2 (yellow 2)
5Input 2 — configurable sensor (white)
6Auxiliary output #1 (yellow 1)
7Input 3 — coolant temperature (pink)
8Auxiliary output #4 (yellow 4)
9Input 4 — configurable sensor (blue)
10Ignition output E (gray E)
11TPS signal / TPS 1 on electronic throttle (orange)
12Ignition output D (gray D)
13MAP signal output (yellow/red)
14Ignition output C (gray C)
15Camshaft position sensor input (green/yellow)
16Ignition output B (gray B)
17RPM signal input (shielded cable)
18Ignition output A (gray A)
19Battery negative / signal ground (black)
205 V sensor supply (green/red)
21Switched 12 V supply (red)
22Power ground (black/white)
23Fuel injector bank B negative (brown)
24Fuel injector bank A negative (purple)

FT400 16-way auxiliary connector

Section 5.2 applies this connector to FT400 only. The manufacturer's table repeats “auxiliary #7” for pins 4, 6 and 8, although the harness diagram labels them #7, #6 and #5 respectively. Confirm these outputs and wiring with FuelTech; the table also disagrees with the diagram on the #1/#2 suffixes of the paired motor wire colours, while agreeing on their motor function.

PinFunction
1O2 sensor input
2Ignition output F
3Electronic throttle TPS 2
4Auxiliary output #7 (yellow #7)
5Two-step input
6Yellow #6 auxiliary output — table calls it #7; see note
7A/C button input
8Yellow #5 auxiliary output — table calls it #7; see note
9Power ground
10Pedal signal #1
11Throttle or pedal sensor ground output
12Pedal signal #2
13Electronic throttle motor #1 / step motor coil #1
14Electronic throttle motor #2 / step motor coil #2
15Electronic throttle motor #1 / step motor coil #1
16Electronic throttle motor #2 / step motor coil #2

Structured pinout

A structured pin index and redrawn connector diagrams are in FuelTech FT350 and FT400 connector pinout. It covers the shared 24-way main connector and the FT400's 16-way auxiliary connector.

Supported configurations

FuelTech's FT350 / FT400 manual (section 4, manufacturer specification) lists support for 1, 2, 3, 4, 5, 6, 8, 10 and 12-cylinder engines up to 16,000 rpm, with a built-in 7 bar (100 psi) MAP sensor and a 4.3-inch colour touch screen. Ignition is controlled from a crankshaft trigger wheel or a distributor. Fuel is delivered through two independent injector banks controlling up to twelve injectors, or more with a peak-and-hold module. The FT400 adds electronic pedal and throttle control, closed-loop lambda control, automatic fuel-map adjustment and seven auxiliary outputs. The FT350 has four auxiliary outputs and four configurable sensor inputs. The listed working temperature range is −10 °C to 60 °C. FuelTech FT350 / FT400 manual, accessed 19 November 2026.

Not established

The microcontroller used in the FT350 and FT400 is not named in FuelTech's published documentation.