The project NA6 plug-in replaces the factory 48-pin ECU on 1.6-litre NA cars from 1989–1993 and some 1.6-litre vehicles up to 1995. Check the original two-plug connector and vehicle wiring; year alone does not establish compatibility.
Installation and pinout source
The stock airflow meter is not operated by Speeduino. The project recommends a manifold-pressure connection, variable TPS and suitable intake-air-temperature sensor. Its guide states that the ST_SIG fuse must be removed for the documented stock fuel-pump control method. Consult the NA6-specific installation and wiring guide before powering the ECU. The official NA6 PCB files identify board revisions. The 48-pin car connector is not the universal v0.4 IDC connector.
Confirm exact assembled revision, modifications, controller and firmware before wiring. Sensor conditioning and compatible drivers matter; see project hardware requirements.
Factory connector — NA6 PCB revision 1.3
These labels and net names are transcribed from J1 on sheet 5 of the Speeduino NA6 v1.3 schematic. The schematic uses both a 1–48 symbol number and a factory-style cavity label; both are shown. “No connection shown” describes this PCB schematic only and does not establish that a vehicle loom cavity is empty. Confirm the PCB version, jumper settings and connector orientation in the original.
| Schematic number | Cavity label | PCB net/function |
|---|---|---|
| 1 | 1A | No connection shown |
| 2 | 1C | ST_Sig |
| 3 | 1E | No connection shown |
| 4 | 1G | Ignition 1 output |
| 5 | 1I | No connection shown |
| 6 | 1K | No connection shown |
| 7 | 1M | VSS |
| 8 | 1O | No connection shown |
| 9 | 1Q | AC-Jump |
| 10 | 1S | No connection shown |
| 11 | 1U | No connection shown |
| 12 | 2A | Ground |
| 13 | 2C | Ground |
| 14 | 2E | Crank input |
| 15 | 2G | Cam input |
| 16 | 2I | Tachometer output |
| 17 | 2K | No connection shown |
| 18 | 2M | TPS sensor |
| 19 | 2O | ROUT1 |
| 20 | 2Q | Coolant temperature sensor |
| 21 | 2S | No connection shown |
| 22 | 2U | Injector 1 output |
| 23 | 2W | Idle output |
| 24 | 2Y | Injector 3 output |
| 25 | 1B | Switched 12 V / battery reference |
| 26 | 1D | No connection shown |
| 27 | 1F | No connection shown |
| 28 | 1H | Ignition 2 output |
| 29 | 1J | AC-Jump |
| 30 | 1L | No connection shown |
| 31 | 1N | VDDA |
| 32 | 1P | No connection shown |
| 33 | 1R | Fan output |
| 34 | 1T | No connection shown |
| 35 | 1V | Clutch input |
| 36 | 2B | Ground |
| 37 | 2D | Ground |
| 38 | 2F | Crank input through jumper JP2 |
| 39 | 2H | No connection shown |
| 40 | 2J | No connection shown |
| 41 | 2L | TPS sensor |
| 42 | 2N | Oxygen sensor |
| 43 | 2P | Intake air temperature sensor |
| 44 | 2R | No connection shown |
| 45 | 2T | ROUT1, marked NA8 alternative fuel pump |
| 46 | 2V | Injector 2 output |
| 47 | 2X | Boost output |
| 48 | 2Z | Injector 4 output |
ROUT1 appears at both 2O and 2T on this schematic, with 2T annotated for an NA8 alternative fuel pump. The separate installation guide describes an alternative fuel pump method using 2O; verify the exact board, vehicle and jumper configuration. The manual's ST_SIG fuse instruction remains relevant for its documented primary fuel-pump setup.