Overview and hardware
Syvecs S6-I is a British engine-management ECU. Legacy S6-I multi-connector system and predecessor to S7-I. Its manufacturer guide identifies connector A as a 34-way key-1 connector with main relay output A1 and H-bridge output A2. Do not apply the S6GP single-connector numbering to an S6-I harness.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S6-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
The following positions are from the Syvecs S6-I wiring guide. N/A reproduces the guide's unavailable label. Function examples can be reassigned; identify the connector view, build options and current limits in the original before wiring.
Connector A
| Pin | Source label |
|---|---|
| A1 | PWR CTR OUT |
| A2 | H‐Bridge1 / SlaveOut1 |
| A3 | H‐Bridge2/ SlaveOut2 |
| A4 | N/A |
| A5 | N/A |
| A6 | N/A |
| A7 | N/A |
| A8 | N/A |
| A9 | N/A |
| A10 | FUEL1 |
| A11 | FUEL2 |
| A12 | FUEL3 |
| A13 | FUEL4 |
| A14 | FUEL5 |
| A15 | FUEL6 |
| A16 | FUEL7 |
| A17 | FUEL8 |
| A18 | FUEL9/PWM1 |
| A19 | FUEL10/PWM2 |
| A20 | FUEL11/PWM3 |
| A21 | FUEL12/PWM4 |
| A22 | FUEL13/PWM5 |
| A23 | FUEL14/PWM6 |
| A24 | FUEL15/PWM7 |
| A25 | FUEL16/PWM8 |
| A26 | IGN1 |
| A27 | IGN2 |
| A28 | IGN3 |
| A29 | IGN4 |
| A30 | IGN5 |
| A31 | IGN6 |
| A32 | PWRGND |
| A33 | PWRGND |
| A34 | PWRGND |
Connector B
| Pin | Source label |
|---|---|
| B1 | PWRGND |
| B2 | EGT2 + |
| B3 | EGT2 ‐ |
| B4 | KNOCK |
| B5 | N/A |
| B6 | PVBAT |
| B7 | VBAT |
| B8 | LAM1A |
| B9 | LAM1B |
| B10 | LAM1C |
| B11 | LAM1D |
| B12 | N/A |
| B13 | VBAT |
| B14 | N/A |
| B15 | N/A |
| B16 | N/A |
| B17 | N/A |
| B18 | N/A |
| B19 | VBAT |
| B20 | KLINE |
| B21 | RS232RX / Can2 L |
| B22 | RS232TX / Can2 H |
| B23 | LANRX‐ |
| B24 | LANRX+ |
| B25 | LANTX‐ |
| B26 | LANTX+ |
Connector C
| Pin | Source label |
|---|---|
| C1 | KNOCK GROUNDS |
| C2 | ANGND |
| C3 | ANGND |
| C4 | N/A |
| C5 | 5V OUT |
| C6 | 5V OUT |
| C7 | N/A |
| C8 | CAN L |
| C9 | CAN H |
| C10 | AN01 |
| C11 | AN02 |
| C12 | AN03 |
| C13 | AN04 |
| C14 | AN05 |
| C15 | AN06 |
| C16 | AN07 |
| C17 | AN08 |
| C18 | AN09 |
| C19 | AN10 |
| C20 | AN11 |
| C21 | AN12 |
| C22 | AN13 |
| C23 | AN14 |
| C24 | AN15 |
| C25 | AN16 |
| C26 | EGT1‐ |
| C27 | EGT1+ |
| C28 | PWR CTR IN |
| C29 | N/A |
| C30 | N/A |
| C31 | N/A |
| C32 | N/A |
| C33 | N/A |
| C34 | N/A |
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.