MoTeC M8, part 11003, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. Early Gold Box family. Manufacturer Gold Box archive; manufacturer model glossary.
Identification and compatibility
Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M8-specific documentation.
Pinout and software
Consult the MoTeC M8 product and wiring downloads and MoTeC legacy downloads. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.
These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.
Manufacturer wiring diagram pinout
Transcribed from the M8 ECU wiring drawing on printed page 57 of the MoTeC M4/M48/M8 user manual. The model-specific drawing and ECU connector view define the orientation. Shared ignition and auxiliary or digital-input functions depend on the configuration. Pins described only by the PC connector connection are identified that way; do not assume their signalling standard. Check hardware revision, electrical loads and trigger wiring against the original.
Connector A — 36 way
| Pin | Function in manufacturer drawing |
|---|---|
| 1 | Power ground |
| 2 | Battery positive |
| 3 | Digital input 4 / ignition 1 |
| 4 | Digital input 3 / ignition 2 |
| 5 | Injector 1 |
| 6 | Injector 2 |
| 7 | Injector 3 |
| 8 | Injector 4 |
| 9 | PWM output 1 |
| 10 | Sensor 0 V |
| 11 | Sensor 8 V |
| 12 | Sensor 5 V |
| 13 | Power ground |
| 14 | Battery positive |
| 15 | Digital input 2 / ignition 3 |
| 16 | Digital input 1 / ignition 4 |
| 17 | Injector 5 |
| 18 | Injector 6 |
| 19 | Injector 7 |
| 20 | Injector 8 |
| 21 | PWM output 2 |
| 22 | Sensor 0 V |
| 23 | Switch input |
| 24 | Lambda 1 + |
| 25 | Engine temperature |
| 26 | Air temperature |
| 27 | Exhaust manifold pressure |
| 28 | Manifold pressure |
| 29 | Throttle position |
| 30 | SYNC pull-up |
| 31 | SYNC + |
| 32 | SYNC − |
| 33 | REF pull-up |
| 34 | REF + |
| 35 | REF − |
| 36 | Lambda 1 − |
Connector B — 18 way
| Pin | Function in manufacturer drawing |
|---|---|
| 1 | Sensor 5 V |
| 2 | Sensor 0 V |
| 3 | Sensor 0 V |
| 4 | Lambda 2 + |
| 5 | Switched output 1 |
| 6 | Switched output 2 |
| 7 | Fuel temperature |
| 8 | Auxiliary temperature 1 |
| 9 | Auxiliary temperature 2 |
| 10 | Lambda 2 − |
| 11 | Stepper motor 4 |
| 12 | Stepper motor 3 |
| 13 | Fuel pressure |
| 14 | Auxiliary temperature 3 |
| 15 | Auxiliary temperature 4 |
| 16 | Knock |
| 17 | Stepper motor 2 |
| 18 | Stepper motor 1 |