Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
AEM Performance Electronics standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 4

Removed text is struck through; added text is highlighted.

EMS-4 with a full harness. Image: AEM installation and tuning guide, page 7; reproduced with permission.

AEM EMS-4 is a universal programmable 30-6905 ECU intended for up to four cylinders. AEM lists a model-specific installation manual and connector reference and compatible flying-lead or mini harnesses in its support archive.

ProcessorAEM's EMS-4 specification table gives the CPU core as 16-bit running at 40 MHz (manufacturer documentation). The manufacturer and part number of the microcontroller are not named in the guide and are not established. Memory sizes are likewise not stated in the sources consulted.Engine applicationsThe EMS-4 is a universal controller, not a vehicle-specific one. Its specification lists four saturated injector drivers (high-impedance injectors only, 8 ohm minimum), four 0-5 V falling-edge coil drivers, eight general-purpose pins, one 0-5 V oxygen sensor input, magnetic (VR) and Hall crank and cam inputs, and a programmable knock input, so it suits engines of up to four cylinders with a manifold-pressure load signal. No factory engine list exists; engine codes depend on the installer's configuration.

Hardware and connections

The manufacturer describes a compact weather-resistant engine controller with a 36-way connector. Ignition drive, injection loads and trigger polarity require confirmation in the exact product instructions. AEM's UEGO gauge application table identifies pin 20 as lambda input 1 and pin 35 as sensor ground for 30-6905; these are ECU pin numbers, not sensor connector pins.

Software and sourcing

The AEM archive lists AEMTuner 2.98 for EMS-4, distinct from InfinityTuner. Record ECU number, firmware and existing calibration before connecting. The system has been described as discontinued by Real Street Performance; verify support and availability with AEM.

See the AEM manufacturer index. Sources reviewed 17 November 2026.

Connector pinoutA structured pin table with a redrawn connector diagram is on AEM EMS-4 connector pinout. The pin functions below match it.36-way main ECU connector - EMS-4 30-6905Pin functions transcribed from the AEM EMS-4 installation and tuning guide, rev 1.6, pages 8-9. Its full-harness and mini-harness diagrams identify the ECU connector as viewed from the terminal end. GPIO 5-8 are PWM capable; verify configuration, fusing, grounds and output current before connecting. Coil outputs are logic signals and cannot drive coil primaries directly.PinFunction1Switched 12 V input2Injector 13Injector 24Injector 35Injector 46Coil 1 output7Coil 2 output8Coil 3 output9Coil 4 output10GPIO 111GPIO 212GPIO 313GPIO 414GPIO 5 (PWM capable)15GPIO 6 (PWM capable)16GPIO 7 (PWM capable)17GPIO 8 (PWM capable)18Battery negative19Battery negative20O2 sensor input21Cam sensor magnetic input22Crank sensor magnetic input23Vehicle speed sensor Hall input24Cam sensor Hall input25Crank sensor Hall input26Knock sensor 1 input27Throttle position sensor28Manifold pressure sensor29Coolant temperature sensor30Inlet air temperature sensor31USB data -32USB data +33CAN +34CAN -35Sensor ground36VCC / sensor supplySourcesAEM EMS-4 Install and Tuning Guide, rev 1.6, AEM Performance Electronics. Accessed 19 November 2026.36-way main ECU connector — EMS-4 30-6905Pin functions transcribed from the AEM EMS-4 installation and tuning guide, rev 1.6, pages 8–9. Its full-harness and mini-harness diagrams identify the ECU connector as viewed from the terminal end. GPIO 5–8 are PWM capable; verify configuration, fusing, grounds and output current before connecting. Coil outputs are logic signals and cannot drive coil primaries directly.PinFunction1Switched 12 V input2Injector 13Injector 24Injector 35Injector 46Coil 1 output7Coil 2 output8Coil 3 output9Coil 4 output10GPIO 111GPIO 212GPIO 313GPIO 414GPIO 5 (PWM capable)15GPIO 6 (PWM capable)16GPIO 7 (PWM capable)17GPIO 8 (PWM capable)18Battery negative19Battery negative20O2 sensor input21Cam sensor magnetic input22Crank sensor magnetic input23Vehicle speed sensor Hall input24Cam sensor Hall input25Crank sensor Hall input26Knock sensor 1 input27Throttle position sensor28Manifold pressure sensor29Coolant temperature sensor30Inlet air temperature sensor31USB data −32USB data +33CAN +34CAN −35Sensor ground36VCC / sensor supply

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: AEM EMS-4

AEM EMS-4 is a universal programmable 30-6905 ECU intended for up to four cylinders. AEM lists a model-specific installation manual and connector reference and compatible flying-lead or mini harnesses in its support archive.

Hardware and connections

The manufacturer describes a compact weather-resistant engine controller with a 36-way connector. Ignition drive, injection loads and trigger polarity require confirmation in the exact product instructions. AEM's UEGO gauge application table identifies pin 20 as lambda input 1 and pin 35 as sensor ground for 30-6905; these are ECU pin numbers, not sensor connector pins.

Software and sourcing

The AEM archive lists AEMTuner 2.98 for EMS-4, distinct from InfinityTuner. Record ECU number, firmware and existing calibration before connecting. The system has been described as discontinued by Real Street Performance; verify support and availability with AEM.

See the AEM manufacturer index. Sources reviewed 17 November 2026.

36-way main ECU connector — EMS-4 30-6905

Pin functions transcribed from the AEM EMS-4 installation and tuning guide, rev 1.6, pages 8–9. Its full-harness and mini-harness diagrams identify the ECU connector as viewed from the terminal end. GPIO 5–8 are PWM capable; verify configuration, fusing, grounds and output current before connecting. Coil outputs are logic signals and cannot drive coil primaries directly.

PinFunction
1Switched 12 V input
2Injector 1
3Injector 2
4Injector 3
5Injector 4
6Coil 1 output
7Coil 2 output
8Coil 3 output
9Coil 4 output
10GPIO 1
11GPIO 2
12GPIO 3
13GPIO 4
14GPIO 5 (PWM capable)
15GPIO 6 (PWM capable)
16GPIO 7 (PWM capable)
17GPIO 8 (PWM capable)
18Battery negative
19Battery negative
20O2 sensor input
21Cam sensor magnetic input
22Crank sensor magnetic input
23Vehicle speed sensor Hall input
24Cam sensor Hall input
25Crank sensor Hall input
26Knock sensor 1 input
27Throttle position sensor
28Manifold pressure sensor
29Coolant temperature sensor
30Inlet air temperature sensor
31USB data −
32USB data +
33CAN +
34CAN −
35Sensor ground
36VCC / sensor supply
Revision 4: AEM EMS-4
AEM EMS-4 ECU and full wiring harness
EMS-4 with a full harness. Image: AEM installation and tuning guide, page 7; reproduced with permission.

AEM EMS-4 is a universal programmable 30-6905 ECU intended for up to four cylinders. AEM lists a model-specific installation manual and connector reference and compatible flying-lead or mini harnesses in its support archive.

Processor

AEM's EMS-4 specification table gives the CPU core as 16-bit running at 40 MHz (manufacturer documentation). The manufacturer and part number of the microcontroller are not named in the guide and are not established. Memory sizes are likewise not stated in the sources consulted.

Engine applications

The EMS-4 is a universal controller, not a vehicle-specific one. Its specification lists four saturated injector drivers (high-impedance injectors only, 8 ohm minimum), four 0-5 V falling-edge coil drivers, eight general-purpose pins, one 0-5 V oxygen sensor input, magnetic (VR) and Hall crank and cam inputs, and a programmable knock input, so it suits engines of up to four cylinders with a manifold-pressure load signal. No factory engine list exists; engine codes depend on the installer's configuration.

Hardware and connections

The manufacturer describes a compact weather-resistant engine controller with a 36-way connector. Ignition drive, injection loads and trigger polarity require confirmation in the exact product instructions. AEM's UEGO gauge application table identifies pin 20 as lambda input 1 and pin 35 as sensor ground for 30-6905; these are ECU pin numbers, not sensor connector pins.

Software and sourcing

The AEM archive lists AEMTuner 2.98 for EMS-4, distinct from InfinityTuner. Record ECU number, firmware and existing calibration before connecting. The system has been described as discontinued by Real Street Performance; verify support and availability with AEM.

See the AEM manufacturer index. Sources reviewed 17 November 2026.

Connector pinout

A structured pin table with a redrawn connector diagram is on AEM EMS-4 connector pinout. The pin functions below match it.

36-way main ECU connector - EMS-4 30-6905

Pin functions transcribed from the AEM EMS-4 installation and tuning guide, rev 1.6, pages 8-9. Its full-harness and mini-harness diagrams identify the ECU connector as viewed from the terminal end. GPIO 5-8 are PWM capable; verify configuration, fusing, grounds and output current before connecting. Coil outputs are logic signals and cannot drive coil primaries directly.

PinFunction
1Switched 12 V input
2Injector 1
3Injector 2
4Injector 3
5Injector 4
6Coil 1 output
7Coil 2 output
8Coil 3 output
9Coil 4 output
10GPIO 1
11GPIO 2
12GPIO 3
13GPIO 4
14GPIO 5 (PWM capable)
15GPIO 6 (PWM capable)
16GPIO 7 (PWM capable)
17GPIO 8 (PWM capable)
18Battery negative
19Battery negative
20O2 sensor input
21Cam sensor magnetic input
22Crank sensor magnetic input
23Vehicle speed sensor Hall input
24Cam sensor Hall input
25Crank sensor Hall input
26Knock sensor 1 input
27Throttle position sensor
28Manifold pressure sensor
29Coolant temperature sensor
30Inlet air temperature sensor
31USB data -
32USB data +
33CAN +
34CAN -
35Sensor ground
36VCC / sensor supply

Sources