Removed text is struck through; added text is highlighted.
Syvecs manufacturer product photograph, reproduced with permission. Image source.
Overview and hardware
Syvecs S7-I is a British engine-management ECU. 16 general-purpose inputs, 16 low-side outputs, 6 ignition, 2 half bridges; 1 lambda, 1 knock and 1 EGT; 94 pins. Second CAN bus was introduced in September 2020. Units purchased before January 2026 have 16 MB logging, later units 64 MB standard, 128 MB optional. Its I/O connector arrangement is shared with S7Plus, subject to application.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S7-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
All 94 positions below follow the Syvecs S7-I model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.
The guide identifies connector B positions 2–3 as switchable or build-dependent between CAN 2 and EGT2, and notes a change for units ordered from September 2020. Confirm the actual build before using them.
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.
Syvecs product or ECU comparisonSyvecs ECU comparison and specification notesSyvecs product historyManufacturer wiring reference
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs S7-ISyvecs manufacturer product photograph, reproduced with permission. Image source.
Overview and hardware
Syvecs S7-I is a British engine-management ECU. 16 general-purpose inputs, 16 low-side outputs, 6 ignition, 2 half bridges; 1 lambda, 1 knock and 1 EGT; 94 pins. Second CAN bus was introduced in September 2020. Units purchased before January 2026 have 16 MB logging, later units 64 MB standard, 128 MB optional. Its I/O connector arrangement is shared with S7Plus, subject to application.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S7-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
All 94 positions below follow the Syvecs S7-I model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.
The guide identifies connector B positions 2–3 as switchable or build-dependent between CAN 2 and EGT2, and notes a change for units ordered from September 2020. Confirm the actual build before using them.
Connector A
Pin
Source label
A1
PWR CTR OUT
A2
H-Bridge1 / SlaveOut1
A3
H-Bridge2/ SlaveOut2
A4
N/A
A5
N/A
A6
N/A
A7
N/A
A8
N/A
A9
N/A
A10
FUEL1
A11
FUEL2
A12
FUEL3
A13
FUEL4
A14
FUEL5
A15
FUEL6
A16
FUEL7
A17
FUEL8
A18
FUEL9/PWM1
A19
FUEL10/PWM2
A20
FUEL11/PWM3
A21
FUEL12/PWM4
A22
FUEL13/PWM5
A23
FUEL14/PWM6
A24
FUEL15/PWM7
A25
FUEL16/PWM8
A26
IGN1
A27
IGN2
A28
IGN3
A29
IGN4
A30
IGN5
A31
IGN6
A32
PWRGND
A33
PWRGND
A34
PWRGND
Connector B
Pin
Source label
B1
PWRGND
B2
EGT2 + / CAN2L
B3
EGT2 - /CAN2H
B4
KNOCK
B5
N/A
B6
PVBAT
B7
VBAT
B8
LAM1A
B9
LAM1B
B10
LAM1C
B11
LAM1D
B12
N/A
B13
VBAT
B14
N/A
B15
N/A
B16
N/A
B17
N/A
B18
N/A
B19
VBAT
B20
KLINE
B21
RS232RX
B22
RS232TX
B23
LANRX-
B24
LANRX+
B25
LANTX-
B26
LANTX+
Connector C
Pin
Source label
C1
KNOCK GROUNDS
C2
ANGND
C3
ANGND
C4
N/A
C5
5V OUT
C6
5V OUT
C7
N/A
C8
CAN L
C9
CAN H
C10
AN01
C11
AN02
C12
AN03
C13
AN04
C14
AN05
C15
AN06
C16
AN07
C17
AN08
C18
AN09
C19
AN10
C20
AN11
C21
AN12
C22
AN13
C23
AN14
C24
AN15
C25
AN16
C26
EGT1-
C27
EGT1+
C28
PWR CTR IN
C29
N/A
C30
N/A
C31
N/A
C32
N/A
C33
N/A
C34
N/A
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.
Revision 2: Syvecs S7-ISyvecs manufacturer product photograph, reproduced with permission. Image source.
Overview and hardware
Syvecs S7-I is a British engine-management ECU. 16 general-purpose inputs, 16 low-side outputs, 6 ignition, 2 half bridges; 1 lambda, 1 knock and 1 EGT; 94 pins. Second CAN bus was introduced in September 2020. Units purchased before January 2026 have 16 MB logging, later units 64 MB standard, 128 MB optional. Its I/O connector arrangement is shared with S7Plus, subject to application.
Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.
Wiring and pinout
Manufacturer S7-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.
Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.
Complete connector pin assignments
All 94 positions below follow the Syvecs S7-I model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.
The guide identifies connector B positions 2–3 as switchable or build-dependent between CAN 2 and EGT2, and notes a change for units ordered from September 2020. Confirm the actual build before using them.
Connector A
Pin
Source label
A1
PWR CTR OUT
A2
H-Bridge1 / SlaveOut1
A3
H-Bridge2/ SlaveOut2
A4
N/A
A5
N/A
A6
N/A
A7
N/A
A8
N/A
A9
N/A
A10
FUEL1
A11
FUEL2
A12
FUEL3
A13
FUEL4
A14
FUEL5
A15
FUEL6
A16
FUEL7
A17
FUEL8
A18
FUEL9/PWM1
A19
FUEL10/PWM2
A20
FUEL11/PWM3
A21
FUEL12/PWM4
A22
FUEL13/PWM5
A23
FUEL14/PWM6
A24
FUEL15/PWM7
A25
FUEL16/PWM8
A26
IGN1
A27
IGN2
A28
IGN3
A29
IGN4
A30
IGN5
A31
IGN6
A32
PWRGND
A33
PWRGND
A34
PWRGND
Connector B
Pin
Source label
B1
PWRGND
B2
EGT2 + / CAN2L
B3
EGT2 - /CAN2H
B4
KNOCK
B5
N/A
B6
PVBAT
B7
VBAT
B8
LAM1A
B9
LAM1B
B10
LAM1C
B11
LAM1D
B12
N/A
B13
VBAT
B14
N/A
B15
N/A
B16
N/A
B17
N/A
B18
N/A
B19
VBAT
B20
KLINE
B21
RS232RX
B22
RS232TX
B23
LANRX-
B24
LANRX+
B25
LANTX-
B26
LANTX+
Connector C
Pin
Source label
C1
KNOCK GROUNDS
C2
ANGND
C3
ANGND
C4
N/A
C5
5V OUT
C6
5V OUT
C7
N/A
C8
CAN L
C9
CAN H
C10
AN01
C11
AN02
C12
AN03
C13
AN04
C14
AN05
C15
AN06
C16
AN07
C17
AN08
C18
AN09
C19
AN10
C20
AN11
C21
AN12
C22
AN13
C23
AN14
C24
AN15
C25
AN16
C26
EGT1-
C27
EGT1+
C28
PWR CTR IN
C29
N/A
C30
N/A
C31
N/A
C32
N/A
C33
N/A
C34
N/A
Calibration and sources
Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.