Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Syvecs S7-I ECU
Syvecs manufacturer product photograph, reproduced with permission. Image source.

Overview and hardware

Syvecs S7-I is a British engine-management ECU. 16 general-purpose inputs, 16 low-side outputs, 6 ignition, 2 half bridges; 1 lambda, 1 knock and 1 EGT; 94 pins. Second CAN bus was introduced in September 2020. Units purchased before January 2026 have 16 MB logging, later units 64 MB standard, 128 MB optional. Its I/O connector arrangement is shared with S7Plus, subject to application.

Compare the required injector, ignition, actuator and sensor channels with the hardware available on the actual ECU. Capabilities and configurable functions depend on firmware, hardware revision and calibration.

Wiring and pinout

Manufacturer S7-I wiring guide and pinout. Use the guide's connector view and pin numbering and verify ECU hardware revision and configuration before wiring. Pin and input functions may vary by calibration or vehicle. Syvecs wiring index contains further example pinout files.

Vehicle-specific replacement kits use their own harness or carrier board. Consult the corresponding vehicle-specific Syvecs guide rather than assuming a generic schedule applies.

Complete connector pin assignments

All 94 positions below follow the Syvecs S7-I model-specific wiring guide, using the guide's source labels. N/A reproduces a source-marked unavailable position. Pin names describe hardware channels; assignments, software configuration, connector orientation, hardware options and electrical limits must be checked in that guide for the exact ECU.

The guide identifies connector B positions 2–3 as switchable or build-dependent between CAN 2 and EGT2, and notes a change for units ordered from September 2020. Confirm the actual build before using them.

Connector A

PinSource label
A1PWR CTR OUT
A2H-Bridge1 / SlaveOut1
A3H-Bridge2/ SlaveOut2
A4N/A
A5N/A
A6N/A
A7N/A
A8N/A
A9N/A
A10FUEL1
A11FUEL2
A12FUEL3
A13FUEL4
A14FUEL5
A15FUEL6
A16FUEL7
A17FUEL8
A18FUEL9/PWM1
A19FUEL10/PWM2
A20FUEL11/PWM3
A21FUEL12/PWM4
A22FUEL13/PWM5
A23FUEL14/PWM6
A24FUEL15/PWM7
A25FUEL16/PWM8
A26IGN1
A27IGN2
A28IGN3
A29IGN4
A30IGN5
A31IGN6
A32PWRGND
A33PWRGND
A34PWRGND

Connector B

PinSource label
B1PWRGND
B2EGT2 + / CAN2L
B3EGT2 - /CAN2H
B4KNOCK
B5N/A
B6PVBAT
B7VBAT
B8LAM1A
B9LAM1B
B10LAM1C
B11LAM1D
B12N/A
B13VBAT
B14N/A
B15N/A
B16N/A
B17N/A
B18N/A
B19VBAT
B20KLINE
B21RS232RX
B22RS232TX
B23LANRX-
B24LANRX+
B25LANTX-
B26LANTX+

Connector C

PinSource label
C1KNOCK GROUNDS
C2ANGND
C3ANGND
C4N/A
C55V OUT
C65V OUT
C7N/A
C8CAN L
C9CAN H
C10AN01
C11AN02
C12AN03
C13AN04
C14AN05
C15AN06
C16AN07
C17AN08
C18AN09
C19AN10
C20AN11
C21AN12
C22AN13
C23AN14
C24AN15
C25AN16
C26EGT1-
C27EGT1+
C28PWR CTR IN
C29N/A
C30N/A
C31N/A
C32N/A
C33N/A
C34N/A

Calibration and sources

Syvecs uses SCal calibration software and provides firmware and base calibrations. Check version compatibility with the unit and preserve the existing tune before changes.