MoTeC M880, part 13002, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. Up to twelve cylinders or four rotors with the appropriate configuration. Manufacturer Gold Box archive; manufacturer model glossary.
Identification and compatibility
Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M880-specific documentation.
Pinout and software
Consult the MoTeC M880 product and wiring downloads and M400/M600/M800/M880 manufacturer manual. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.
These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.
Manufacturer connector pin list
From Appendix L of the MoTeC M400/M600/M800/M880 user manual (7 November 2003). This is the 66-position M800/M880 connector; positions 20, 21 and 22 are not listed in this appendix. Outputs marked * have no recirculation diode. Refer to the original connector view, wiring diagrams and electrical limits; output assignment may depend on model and configuration.
| Pin | Designation | Function and model restrictions |
|---|---|---|
| 23,32,41 | VBAT | Battery positive |
| 14,15,19 | GND | Battery negative |
| 3 | 8V-ENG | 8 V engine sensor supply |
| 16 | 5V-ENG | 5 V engine sensor supply |
| 27 | 0V-ENG | Engine sensor ground |
| 2 | 8V-AUX | 8 V auxiliary sensor and CAN supply |
| 34 | 5V-AUX | 5 V auxiliary sensor supply |
| 11 | 0V-AUX | Auxiliary sensor ground |
| 9 | AUX1 | Auxiliary output 1 |
| 8 | AUX2 | Auxiliary output 2 |
| 43 | AUX3* | Auxiliary output 3 |
| 51 | AUX4* | Auxiliary output 4 |
| 59 | AUX5 | Auxiliary output 5 |
| 65 | AUX6 | Auxiliary output 6 |
| 58 | AUX7 | Auxiliary output 7 |
| 64 | AUX8 | Auxiliary output 8 |
| 1 | IGN1* | Ignition output 1 |
| 5 | IGN2* | Ignition output 2 |
| 4 | IGN3* | Ignition output 3 |
| 10 | IGN4* | Ignition output 4 |
| 17 | IGN5* | Ignition output 5; not available on M400 |
| 25 | IGN6* | Ignition output 6; not available on M400 |
| 33 | INJ1 | Injector output 1 |
| 50 | INJ2 | Injector output 2 |
| 63 | INJ3 | Injector output 3 |
| 66 | INJ4 | Injector output 4 |
| 24 | INJ5 | Injector output 5; not available on M400 |
| 42 | INJ6 | Injector output 6; not available on M400 |
| 57 | INJ7 | Injector output 7; not available on M400 or M600 |
| 62 | INJ8 | Injector output 8; not available on M400 or M600 |
| 26 | AV1 | Analogue voltage input 1 |
| 18 | AV2 | Analogue voltage input 2 |
| 6 | AV3 | Analogue voltage input 3 |
| 7 | AV4 | Analogue voltage input 4 |
| 12 | AV5 | Analogue voltage input 5 |
| 36 | AV6 | Analogue voltage input 6 |
| 35 | AV7 | Analogue voltage input 7 |
| 44 | AV8 | Analogue voltage input 8 |
| 28 | AT1 | Analogue temperature input 1 |
| 38 | AT2 | Analogue temperature input 2 |
| 30 | AT3 | Analogue temperature input 3 |
| 39 | AT4 | Analogue temperature input 4 |
| 29 | AT5 | Analogue temperature input 5 |
| 37 | AT6 | Analogue temperature input 6 |
| 46 | DIG1 | Digital input 1 |
| 45 | DIG2 | Digital input 2 |
| 52 | DIG3 | Digital input 3 |
| 53 | DIG4 | Digital input 4 |
| 49 | REF | Crank reference timing input |
| 56 | SYNC | Cam sync timing input |
| 60 | LA1-P | Lambda 1 pump current |
| 54 | LA1-S | Lambda 1 sense voltage |
| 61 | LA2-P | Lambda 2 pump current; not available on M400 |
| 55 | LA2-S | Lambda 2 sense voltage; not available on M400 |
| 40 | TX-232 | RS232 transmit data |
| 31 | RX-232 | RS232 receive data |
| 47 | CAN-LO | CAN bus low |
| 48 | CAN-HI | CAN bus high |
| 13 | 0V-COM | Communications ground |