
FuelTech FT700PLUS is a VisionFT engine-management unit. VisionFT controller with a larger nominal 12-inch display and the FT700-series control architecture; FuelTech lists 36 inputs and 50 outputs. Confirm screen and installation dimensions in the current manual. FuelTech model documentation · FuelTech range comparison.
Identification and software
Record the exact model, serial, harness, firmware and configured outputs; similarly named FT models may use different connectors and functions. Tuning software: FuelTech Vision. FuelTech software and compatibility.
Wiring and pinout
Use the model-specific manual and the current FuelTech manuals index for connector view, cavity numbering, fuse values, sensor grounds and injector-driver limits. The manufacturer wiring archive contains installation-specific examples; match the exact ECU and harness before wiring. Pin functions depend on the model, hardware and configured output.
See FuelTech engine-management family for other models and company background. FuelTech is based in Brazil and has a US operation in Georgia. Sources reviewed 17 November 2026.
FT700-family connector pin assignments
The FuelTech FT700 / FT700Plus quick installation guide describes the 34-way A and B connectors and optional C, D and M harness connections below. Identify the connector from its markings and the guide's rear views. Inputs and outputs can be configured: check the actual calibration, hardware, current limits, relay and ground wiring before connecting loads. In particular, trigger references are not generic grounds for Hall sensors.
A — 34 way
| Pin | Function and harness wire |
|---|---|
| 1 | Blue output #1 (blue #1) |
| 2 | Blue output #2 (blue #2) |
| 3 | Blue output #3 (blue #3) |
| 4 | Blue output #4 (blue #4) |
| 5 | Blue output #5 (blue #5) |
| 6 | Blue output #6 (blue #6) |
| 7 | Blue output #7 (blue #7) |
| 8 | Blue output #8 (blue #8) |
| 9 | Blue output #9 (blue #9) |
| 10 | Blue output #10 (blue #10) |
| 11 | Blue output #11 (blue #11) |
| 12 | Blue output #12 (blue #12) |
| 13 | Blue output #13 (blue #13) |
| 14 | Blue output #14 (blue #14) |
| 15 | Blue output #15 (blue #15) |
| 16 | Blue output #16 (blue #16) |
| 17 | Power ground (black/white) |
| 18 | Gray output #1 (gray #1) |
| 19 | Gray output #2 (gray #2) |
| 20 | Gray output #3 (gray #3) |
| 21 | Gray output #4 (gray #4) |
| 22 | Gray output #5 (gray #5) |
| 23 | Gray output #6 (gray #6) |
| 24 | Gray output #7 (gray #7) |
| 25 | Gray output #8 (gray #8) |
| 26 | Yellow output #1 (yellow #1) |
| 27 | Yellow output #2 (yellow #2) |
| 28 | Yellow output #3 (yellow #3) |
| 29 | Yellow output #4 (yellow #4) |
| 30 | Yellow output #5 (yellow #5) |
| 31 | Yellow output #6 (yellow #6) |
| 32 | Yellow output #7 (yellow #7) |
| 33 | Yellow output #8 (yellow #8) |
| 34 | 12 V input from main relay (red) |
B — 34 way
| Pin | Function and harness wire |
|---|---|
| 1 | RPM signal input (red) |
| 2 | Magnetic RPM sensor reference (white) |
| 3 | Cam sync signal input (red) |
| 4 | Cam sync reference input (white) |
| 5 | White input #1 |
| 6 | White input #2 |
| 7 | White input #3 |
| 8 | White input #4 |
| 9 | White input #5 |
| 10 | Battery negative (black) |
| 11 | CAN A low (yellow/blue) |
| 12 | CAN A high (white/red) |
| 13 | White input #6 |
| 14 | White input #7 |
| 15 | White input #8 |
| 16 | White input #9 |
| 17 | White input #10 |
| 18 | Power ground (black/white) |
| 19 | Power ground (black/white) |
| 20 | CAN B high (white/red) |
| 21 | White input #11 |
| 22 | White input #12 |
| 23 | White input #13 |
| 24 | White input #14 |
| 25 | White input #15 |
| 26 | 12 V input from main relay (red) |
| 27 | 5 V sensor supply (green/red) |
| 28 | CAN B low (yellow/blue) |
| 29 | Sensor ground (green/black) |
| 30 | White input #16 |
| 31 | White input #17 |
| 32 | White input #18 |
| 33 | White input #19 / Power Shift positive |
| 34 | White input #20 / Power Shift negative |
C — 26 way, optional
| Pin | Function |
|---|---|
| 1 | 12 V input from main relay |
| 2 | 12 V input from main relay |
| 3 | 12 V input from main relay |
| 4 | Gray output #9 |
| 5 | Gray output #10 |
| 6 | Gray output #11 |
| 7 | Gray output #12 |
| 8 | Yellow output #9 |
| 9 | Yellow output #10 |
| 10 | Yellow output #11 |
| 11 | Yellow output #12 |
| 12 | Yellow output #13 |
| 13 | Yellow output #14 |
| 14 | Yellow output #15 |
| 15 | Yellow output #16 |
| 16 | Yellow output #17 |
| 17 | Yellow output #18 |
| 18 | CAN C high |
| 19 | CAN C low |
| 20 | Yellow output #19 |
| 21 | Yellow output #20 |
| 22 | O2 sensor #1 heater positive |
| 23 | O2 sensor #2 heater positive |
| 24 | Power ground |
| 25 | Power ground |
| 26 | Power ground |
C22 and C23 can provide sensor-heater positives; the guide also describes alternate yellow-output use when the built-in oxygen conditioners are not used.
D — 26 way, optional
| Pin | Function |
|---|---|
| 1 | Frequency channel #1, red; configurable input #21 |
| 2 | Frequency channel #1, white; configurable input #22 |
| 3 | Frequency channel #2, red; configurable input #23 |
| 4 | Frequency channel #2, white; configurable input #24 |
| 5 | Frequency channel #3, red; configurable input #25 |
| 6 | Frequency channel #3, white; configurable input #26 |
| 7 | Frequency channel #4, red; configurable input #27 |
| 8 | Frequency channel #4, white; configurable input #28 |
| 9 | High-speed input #1; configurable input #29 |
| 10 | High-speed input #2; configurable input #30 |
| 11 | High-speed input #3; configurable input #31 |
| 12 | High-speed input #4; configurable input #32 |
| 13 | High-speed input #5; configurable input #33 |
| 14 | High-speed input #6; configurable input #34 |
| 15 | High-speed input #7; configurable input #35 |
| 16 | High-speed input #8; configurable input #36 |
| 17 | O2 sensor #1 signal |
| 18 | O2 sensor #1 ground |
| 19 | O2 sensor #1 IP |
| 20 | O2 sensor #1 calibration resistor |
| 21 | O2 sensor #1 heater negative |
| 22 | O2 sensor #2 signal |
| 23 | O2 sensor #2 ground |
| 24 | O2 sensor #2 IP |
| 25 | O2 sensor #2 calibration resistor |
| 26 | O2 sensor #2 heater negative |
For O2 sensors, heater positive for #1 is C22 and for #2 is C23. Frequency and high-speed inputs may also be configured as analogue inputs. Follow the source for exact sensor types and output configuration.
M — 14 way, optional
| Pin | Function |
|---|---|
| 1 | Ethernet + |
| 2 | CAN D high |
| 3 | Right microphone input |
| 4 | Right speaker signal |
| 5 | Microphone ground |
| 6 | Video #2 ground |
| 7 | Video #2 signal |
| 8 | Ethernet − |
| 9 | CAN D low |
| 10 | Left microphone input |
| 11 | Left speaker signal |
| 12 | Speaker ground |
| 13 | Video #1 ground |
| 14 | Video #1 signal |
The source's M13 function label says video #1 ground while its information column says video #2; confirm the harness and manufacturer's diagram before connecting.