
The Vi-PEC i44 is a iSeries wire-in programmable engine-management ECU. 4 injector and 4 ignition outputs; the installation manual identifies peak-and-hold capability and a single A connector, with some inputs sharing header pins. The i44 has an internal MAP sensor; the i88 requires an external sensor. Link's archived i44 product page contains some contradictory labels and driver descriptions, so confirm exact hardware and revision. Link-hosted model information.
Wiring and pinout
The official iSeries wiring and installation manual has the i44 header pinout, wiring diagrams and trigger sensor detail. Refer to the correct model and revision, as similar A-connector shells can have different functions, optional drivers and sensor circuitry.
Engine loom connector pinout
The Vi-PEC iSeries installation manual, pages 19, shows the connector viewed into the ECU header or from the wire side of the loom. Numbers below follow the manual's connector diagram; colours describe its standard loom and may differ in a modified harness. Pins 22 and 23 each have shared, selectable functions; see the manual. Confirm configuration, pull-ups and electrical limits in the original before wiring.
Connector A — 34-way
| Pin | Function | Loom colour in manual |
|---|---|---|
| 1 | Injector 4 | Brown/Orange |
| 2 | Injector 3 | Brown/Red |
| 3 | Injector 2 | Brown |
| 4 | Injector 1 | Brown/Black |
| 5 | +14 V | Red |
| 6 | +8 V | Red/White |
| 7 | Shield/Ground | Green |
| 8 | Trigger 1 | Black |
| 9 | Trigger 2 | Red |
| 10 | Ignition 4 | Blue/Orange |
| 11 | Ignition 3 | Blue/Red |
| 12 | Ignition 2 | Blue/Brown |
| 13 | Ignition 1 | Blue |
| 14 | Analogue voltage 4 | White/Black |
| 15 | Temperature 1 | Yellow |
| 16 | Temperature 2 | Yellow/Brown |
| 17 | Analogue voltage 1 | Yellow/Blue |
| 18 | Auxiliary 4 | Orange |
| 19 | Auxiliary 3 | Orange/Red |
| 20 | Auxiliary 2 | Orange/Brown |
| 21 | Auxiliary 1 | Orange/Black |
| 22 | Analogue voltage 2 or digital input 4 | White/Brown |
| 23 | Digital input 3 or knock | Grey/Red |
| 24 | Ground out | Green |
| 25 | Ground | Black |
| 26 | Auxiliary 8 | Orange/Purple |
| 27 | Auxiliary 7 | Orange/Blue |
| 28 | Auxiliary 6 | Orange/Green |
| 29 | Auxiliary 5 | Orange/Yellow |
| 30 | Digital input 1 | Grey/Black |
| 31 | Digital input 2 | Grey/Brown |
| 32 | +5 V | Red/Blue |
| 33 | Analogue voltage 3 | Yellow/Black |
| 34 | Ground | Black |
Communications connector
The six-way communications connector is separate from the engine loom connectors. iSeries installation manual; confirm orientation in the diagram.
| Pin | Wire | Function |
|---|---|---|
| 1 | Brown | Ground |
| 2 | Blue | Not connected |
| 3 | White | CAN high |
| 4 | Green | CAN low |
| 5 | Yellow | ECU RS232 transmit |
| 6 | Grey | ECU RS232 receive |
Tuning and software
Link identifies PCLink for G4+ as compatible with iSeries ECUs. Choose the software matching the ECU firmware and keep a copy of the calibration before making changes. Link Vi-PEC software archive.