Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
DTAFast standalone engine management
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T12+ is a programmable T-series engine ECU. Up to 12 cylinders fully sequential. Dual drive-by-wire, dual knock sensing, four variable cam controls and paddle-shift support. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T12+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Complete connector pin assignments

These pin positions and labels are from the DTAFast T12-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.

Connector 1 — pinout version 1.03

PinFunction in manufacturer diagram1Coil 32Coil 113PWM 34PWM 25PWM 16Motor 1 +7Motor 1 -8Injector 119Injector 110Coil 111Coil 512Coil 713Power Ground 114Power Ground 215Injector 616Injector 517Injector 218Coil 219Coil 820Coil 921Injector 922Injector 1023Injector 824Injector 725Injector 426Coil 427Coil 628Coil 1029Motor 2 +30Motor 2 -31Ignition 12v In32Injector 1233Coil 1234Injector 3

Connector 2 — pinout version 1.03

PinFunction in manufacturer diagram1Analogue 22Wheel 13Analogue 104Digital 15Analogue 36Analogue 47Thermistor 18Digital 295v Output10Analogue 111Digital 312Crank Sensor13Analogue 1214Digital 415Digital 516Analogue 1117Thermistor 318Analogue 519Analogue 620Wheel 221Sensor Ground22Cam 123Cam 3245v Output25Thermistor 226CAN High27Digital 628CAN Low29Cam 230Cam 431Wheel 332Wheel 433Sensor Ground34Analogue 9

Connector 3 — pinout version 1.03

PinFunction in manufacturer diagram1Lambda 2 Pump Current2Lambda 2 VGND3Lambda 2 Heater Negative4PWM 95Lambda 2 Trim Resistor6Lambda 2 Nernst Voltage7Lambda 1 Pump Current8Lambda 1 VGND9Lambda 1 Heater Negative10PWM 811Lambda 1 Trim Resistor12Lambda 1 Nernst Voltage13Analogue 1314Analogue 1415Analogue 1516Analogue 1617Analogue 718Analogue 819Digital 720Digital 821Digital 922PWM 423PWM 524PWM 625PWM 726Permanent 12v27Permanent 12v28PWM 1029PWM 1130PWM 1231Knock 132Knock 233CAN 2 High34CAN 2 Low

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: DTAFast T12 Plus
DTAFast T12 Plus engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T12+ is a programmable T-series engine ECU. Up to 12 cylinders fully sequential. Dual drive-by-wire, dual knock sensing, four variable cam controls and paddle-shift support. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T12+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Complete connector pin assignments

These pin positions and labels are from the DTAFast T12-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.

Connector 1 — pinout version 1.03

PinFunction in manufacturer diagram
1Coil 3
2Coil 11
3PWM 3
4PWM 2
5PWM 1
6Motor 1 +
7Motor 1 -
8Injector 11
9Injector 1
10Coil 1
11Coil 5
12Coil 7
13Power Ground 1
14Power Ground 2
15Injector 6
16Injector 5
17Injector 2
18Coil 2
19Coil 8
20Coil 9
21Injector 9
22Injector 10
23Injector 8
24Injector 7
25Injector 4
26Coil 4
27Coil 6
28Coil 10
29Motor 2 +
30Motor 2 -
31Ignition 12v In
32Injector 12
33Coil 12
34Injector 3

Connector 2 — pinout version 1.03

PinFunction in manufacturer diagram
1Analogue 2
2Wheel 1
3Analogue 10
4Digital 1
5Analogue 3
6Analogue 4
7Thermistor 1
8Digital 2
95v Output
10Analogue 1
11Digital 3
12Crank Sensor
13Analogue 12
14Digital 4
15Digital 5
16Analogue 11
17Thermistor 3
18Analogue 5
19Analogue 6
20Wheel 2
21Sensor Ground
22Cam 1
23Cam 3
245v Output
25Thermistor 2
26CAN High
27Digital 6
28CAN Low
29Cam 2
30Cam 4
31Wheel 3
32Wheel 4
33Sensor Ground
34Analogue 9

Connector 3 — pinout version 1.03

PinFunction in manufacturer diagram
1Lambda 2 Pump Current
2Lambda 2 VGND
3Lambda 2 Heater Negative
4PWM 9
5Lambda 2 Trim Resistor
6Lambda 2 Nernst Voltage
7Lambda 1 Pump Current
8Lambda 1 VGND
9Lambda 1 Heater Negative
10PWM 8
11Lambda 1 Trim Resistor
12Lambda 1 Nernst Voltage
13Analogue 13
14Analogue 14
15Analogue 15
16Analogue 16
17Analogue 7
18Analogue 8
19Digital 7
20Digital 8
21Digital 9
22PWM 4
23PWM 5
24PWM 6
25PWM 7
26Permanent 12v
27Permanent 12v
28PWM 10
29PWM 11
30PWM 12
31Knock 1
32Knock 2
33CAN 2 High
34CAN 2 Low

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.

Revision 3: DTAFast T12 Plus
DTAFast T12 Plus engine management unit
Manufacturer product photograph: DTAFast. Permission to republish confirmed by the user.

DTAFast T12+ is a programmable T-series engine ECU. Up to 12 cylinders fully sequential. Dual drive-by-wire, dual knock sensing, four variable cam controls and paddle-shift support. Manufacturer specification and product photographs.

Control and software

DTAFast describes configurable inputs and outputs, Bosch wideband control, on-board logging, and a trigger oscilloscope in T-Series PC software. Capabilities, logging rates and pin usage vary by unit and firmware; confirm the exact installation and ECU specification. Product details.

Connector pinout and wiring

Use the T12+ manufacturer wiring diagram for numbered connector cavities, diagram orientation, switched and permanent supplies, grounds, actuators, sensors and hardware-revision notes. Outputs can be configurable: confirm assignments and limits in both the diagram and actual calibration. The similarly named non-plus ECU has its own separate pinout.

Complete connector pin assignments

These pin positions and labels are from the DTAFast T12-PLUS wiring diagram, shown from the pin-insertion side. A dash means no function is shown in the drawing. Verify the ECU version, electrical limits and configured functions before wiring.

Connector 1 — pinout version 1.03

PinFunction in manufacturer diagram
1Coil 3
2Coil 11
3PWM 3
4PWM 2
5PWM 1
6Motor 1 +
7Motor 1 -
8Injector 11
9Injector 1
10Coil 1
11Coil 5
12Coil 7
13Power Ground 1
14Power Ground 2
15Injector 6
16Injector 5
17Injector 2
18Coil 2
19Coil 8
20Coil 9
21Injector 9
22Injector 10
23Injector 8
24Injector 7
25Injector 4
26Coil 4
27Coil 6
28Coil 10
29Motor 2 +
30Motor 2 -
31Ignition 12v In
32Injector 12
33Coil 12
34Injector 3

Connector 2 — pinout version 1.03

PinFunction in manufacturer diagram
1Analogue 2
2Wheel 1
3Analogue 10
4Digital 1
5Analogue 3
6Analogue 4
7Thermistor 1
8Digital 2
95v Output
10Analogue 1
11Digital 3
12Crank Sensor
13Analogue 12
14Digital 4
15Digital 5
16Analogue 11
17Thermistor 3
18Analogue 5
19Analogue 6
20Wheel 2
21Sensor Ground
22Cam 1
23Cam 3
245v Output
25Thermistor 2
26CAN High
27Digital 6
28CAN Low
29Cam 2
30Cam 4
31Wheel 3
32Wheel 4
33Sensor Ground
34Analogue 9

Connector 3 — pinout version 1.03

PinFunction in manufacturer diagram
1Lambda 2 Pump Current
2Lambda 2 VGND
3Lambda 2 Heater Negative
4PWM 9
5Lambda 2 Trim Resistor
6Lambda 2 Nernst Voltage
7Lambda 1 Pump Current
8Lambda 1 VGND
9Lambda 1 Heater Negative
10PWM 8
11Lambda 1 Trim Resistor
12Lambda 1 Nernst Voltage
13Analogue 13
14Analogue 14
15Analogue 15
16Analogue 16
17Analogue 7
18Analogue 8
19Digital 7
20Digital 8
21Digital 9
22PWM 4
23PWM 5
24PWM 6
25PWM 7
26Permanent 12v
27Permanent 12v
28PWM 10
29PWM 11
30PWM 12
31Knock 1
32Knock 2
33CAN 2 High
34CAN 2 Low

Identification

Record the exact model suffix, hardware revision, firmware, serial and harness before modifying wiring or calibration. Obtain software and manuals from DTAFast and see the DTAFast family reference for related models and legacy controllers.