Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
SCS Delta standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
SCS Delta GDI4 ECU
SCS Delta GDI4 ECU. Image: SCS Delta SXTune hardware reference; reproduced with permission.

SCS Delta GDI4 is a programmable SCS Delta engine-management controller. Legacy GDI4 direct-injection controller with AMPSeal A 776164-1 and B 776163-5. The documented hardware provides four paired high- and low-side injector connections, electronic throttle, pump control, knock inputs and additional PWM/relay outputs. SCS lists it as a legacy unit; do not substitute the GDI6 pinout. SXTune GDI4 hardware reference.

Pinout and connector identification

Connector B B1–B4 are injector 1–4 high side and B13–B16 injector 1–4 low side. B5–B6 are throttle motor, and B7–B8 are fuel-pump drive in the documented configuration. The complete GDI4 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.

Complete connector pin assignments

These assignments and electrical notes are from the SXTune deltagdi4 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.

The source repeats connector B in two tables with differing example application names at several positions, including B18–B20, B29 and B32. The table below reproduces the first source table's application column; those examples must not be treated as fixed configuration.

Connectors A and B

PinShort NameNameDescriptionApplication
A1VBATTBatteryPower Supply input 6-18VDirect Battery Supply (fuse 15A)
A2VKEYIgnitionIgnition Switch inputIgnition Switched Supply (fuse 10A)
A3P_GND1Power Ground 1Power GroundPower Ground 1
A4OUT1Low Side 13A Open Collector w/recirc diodeHot Soak Relay Control
A5OUT2Low Side 23A Open Collector w/recirc diodeA/C Clutch Relay Control
A6OUT3Low Side 33A Open Collector w/recirc diodePurge Valve Control
A7OUT4Low Side 43A Open Collector w/recirc diodeLambda Heater Drive
A8D_GNDHall GroundDigital GroundCrank/Cam Sensors Ground
A9CRANKHall InputDigital InputCrank Sensor Input
A10CAM1Hall InputDigital InputIntake Cam Input
A11TCOOLNTC Input3.16K pull-up to VREFCoolant Temp Input
A12TAIRNTC Input3.16K pull-up to VREFCharge Air Temp Input
A13IGN1Ignition 1Logic or Power (hardware selected)Ignition Coil 1 Output
A14IGN2Ignition 2Logic or Power (hardware selected)Ignition Coil 2 Output
A15IGN3Ignition 3Logic or Power (hardware selected)Ignition Coil 3 Output
A16IGN4Ignition 4Logic or Power (hardware selected)Ignition Coil 4 Output
A17LINEAR1Analog Input 147k pull-up to VREFFuel Rail Pressure Input
A18CAM2Hall InputDigital InputExhaust Cam Input
A19A_GND1Analog Ground 1Analog GroundTemp Sensors Ground
A20LMBD1Lambda 1 InputWeak bias to 450mVLambda 1 Input
A21CAN1HCAN 1H120 Ohm TerminatedCAN 1 High
A22CAN1LCAN 1LCAN 1 Low
A23HALL1Hall Input 1Digital InputMAF Input
A24OUT5Low Side 53A Open Collector w/recirc diodeMain Relay Output
A25OUT6Low Side 63A Open Collector w/recirc diodeThermostat Control Output
A26OUT7Low Side 73A Open Collector w/recirc diodeIntake Cam PWM Output
A27OUT8Low Side 83A Open Collector w/recirc diodeExhaust Cam PWM Output
A28OUT9Low Side 93A Open Collector w/recirc diodeFan 1 Relay/PWM Output
A29OUT10Low Side 103A Open Collector w/recirc diodeFan 2 Relay/PWM Output
A30A_GND2Analog Ground 2Analog GroundTPS/MAP/MAF Ground
A31NTC1NTC Input 13.16K pull-up to VREFGear Cut Input
A32LINEAR2Analog Input 247k pull-up to VREFThrottle Position Sensor 1 Input
A33LINEAR3Analog Input 347k pull-up to VREFMAP Sensor Input
A34VREF1VREF 15V 500mA sensor supply5V Sensor Supply 1
A35P_GND2Power Ground 2Power GroundPower Ground 2
B1INJ1+Injector 1 +Injector 1 High SideInjector 1 +
B2INJ2+Injector 2 +Injector 2 High SideInjector 2 +
B3INJ3+Injector 3 +Injector 3 High SideInjector 3 +
B4INJ4+Injector 4 +Injector 4 High SideInjector 4 +
B5HBRIDGE1+H Bridge M+5A H-BridgeThrottle +
B6HBRIDGE1-H Bridge M-5A H-BridgeThrottle -
B7HBRIDGE2+Fuel Pump Drive +5A H-BridgeFuel Pump +
B8HBRIDGE2-Fuel Pump Drive -5A H-BridgeFuel Pump -
B9OUT11Low Side 113A Open Collector w/recirc diodeWastegate Valve Output
B10OUT12Low Side 123A Open Collector w/recirc diodeRecirc Valve Output
B11VREF2VREF 25V 500mA sensor supply5V Sensor Supply 2
B12HBRIDGE3+H Bridge 3 M+5A H-BridgeElectronic Turbo Actuator +
B13INJ1-Injector 1 -Injector 1 Low SideInjector 1 -
B14INJ2-Injector 2 -Injector 2 Low SideInjector 2 -
B15INJ3-Injector 3 -Injector 3 Low SideInjector 3 -
B16INJ4-Injector 4 -Injector 4 Low SideInjector 4 -
B17HALL3Hall Input 3Digital InputWheel Speed Input LR
B18HALL4Hall Input 4Digital InputWheel Speed Input RR
B19HALL5Hall Input 5Digital InputWheel Speed Input LF
B20HALL6Hall Input 6Digital InputWheel Speed Input RF
B21KNOCK1Knock 1 +Knock InputKnock Sensor 1 Input
B22KNOCK2Knock 2 +Knock InputKnock Sensor 2 Input
B23K_GNDKnock GroundDigital GroundKnock Sensor Ground
B24HBRIDGE3-H Bridge 3 M-5A H-BridgeElectronic Turbo Actuator -
B25LINEAR4Analog Input 447k pull-up to VREFThrottle Position Sensor 2 Input
B26LINEAR5Analog Input 547k pull-up to VREFPedal Position Sensor 1 Input
B27LINEAR6Analog Input 647k pull-up to VREFPedal Position Sensor 2 Input
B28LINEAR7Analog Input 747k pull-up to VREFOil Pressure Sensor Input
B29LINEAR8Analog Input 847k pull-up to VREFFuel Line Pressure Sensor Input
B30LINEAR9Analog Input 947k pull-up to VREFTraction Control Pot Input
B31LINEAR10Analog Input 1047k pull-up to VREFA/C System Pressure Input
B32LINEAR11Analog Input 1147k pull-up to VREFBoost Pressure Sensor Input
B33NTC2NTC Input 23.16k pull-up to VREFFuel Level Input
B34CAN2HCAN 2 H120 Ohm TerminatedCAN 2 High
B35CAN2LCAN 2 LCAN 2 Low

PC communications DB9 female

PinName
1Ground
6CAN High
7CAN Low
8Battery Voltage

Calibration and installation

Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.

See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.