Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
SCS Delta standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
SCS Delta 880 ECU
SCS Delta 880 ECU. Image: SCS Delta SXTune hardware reference; reproduced with permission.

SCS Delta 880 is a programmable SCS Delta engine-management controller. Legacy two-connector Delta unit listed separately from the 800 in the SXTune hardware archive. The reference shows two throttle bridges, wheel-speed inputs, knock inputs and gearshift-related assignments. Its defaults differ from the 800, so similar-looking plugs do not prove a direct swap. SXTune 880 hardware reference.

Pinout and connector identification

A17 is the gear-position sensor input in the documented application; B9 is a configurable output, B10 is gearshift air-pressure relay, B15 is gear-up solenoid and B16 gear-down solenoid. B1–B4 are the two throttle bridge pairs. These are the documented application functions, not universal settings. The complete 880 connector pinout identifies every pin, its electrical description and the diagram. Numbering is model-specific; verify the connector view, supply fuses and the calibration. Adjacent models can use the same connector family with different functions.

Complete connector pin assignments

These assignments and electrical notes are from the SXTune delta880 technical reference. Application names are examples and some channels are configurable. Confirm the matching hardware revision, orientation, electrical limits and calibration in the source before wiring.

Main Connector

PinNameDescriptionNotes
1BatteryDirect Battery Supply (15A fuse)Direct Battery Power 6-15V
2IgnitionIgnition Switched Supply (10A fuse)Ignition Key Input
3Power Ground 1Power GroundPower Ground
4Low Side Output 13A Open CollectorInjector 1
5Low Side Output 23A Open CollectorInjector 2
6Low Side Output 33A Open CollectorInjector 3
7Low Side Output 43A Open CollectorInjector 4
8Crank/Cam GroundDigital GroundCrank/Cam Sensor Ground
9Crank InputVR/Hall - Software SelectableCrank Sensor Input
10Cam Input 1VR/Hall - Software SelectableInlet Cam Sensor 1 Input
11NTC Input 13.16K pull-up to VREFCoolant Temp Input
12NTC Input 23.16K pull-up to VREFAir Temp Input
13Ignition 1TTL/Power Ignition OutputIgnition 1
14Ignition 2TTL/Power Ignition OutputIgnition 2
15Ignition 3TTL/Power Ignition OutputIgnition 3
16Ignition 4TTL/Power Ignition OutputIgnition 4
17Analog Input 147k pull-up to VREFGear Position Sensor
18Cam Input 2VR/Hall - Software SelectableCam 2 / Wheel Speed
19Analog Ground 1Analog GroundAnalog Ground
20Lambda 1 InputWeak bias to 450mV0-5V Analog Input
21CAN 1H120 Ohm TerminatedTo PC comms DB9
22CAN 1LTo PC comms DB9
23Low Side Output 53A Open CollectorMFIO Injector 5 and Lambda 3 Input
24Low Side Output 73A Open Collector w/ recirc diodeMain Relay/PWM1
25Low Side Output 83A Open Collector w/ recirc diodeFuel Pump Relay/PWM2
26Low Side Output 93A Open Collector w/ recirc diodePWM3
27Low Side Output 103A Open Collector w/ recirc diodePWM4
28Low Side Output 113A Open Collector with pull-up to VBATT via diodeTacho Output
29Low Side Output 63A Open CollectorMFIO Injector 6 and Lambda 4 Input
30Analog Ground 2Analog GroundAnalog Ground
31NTC Input 33.16K pull-up to VREFNTC1
32Analog Input 247k pull-up to VREFTPS1
33Analog Input 347k pull-up to VREFMAP
34VREF500mA 5V supply to sensors5V Reference
35Power Ground 2Power GroundPower Ground 2

Secondary Connector

PinNameDescriptionNotes
B1H Bridge 1 M+5A H-BridgeThrottle 1 +
B2H Bridge 1 M-5A H-BridgeThrottle 1 -
B3H Bridge 2 M+5A H-BridgeThrottle 2 +
B4H Bridge 2 M-5A H-BridgeThrottle 2 -
B5Bipolar Output 13A Hi Side/Lo Side DrivePWM5
B6Bipolar Output 23A Hi Side/Lo Side DrivePWM6
B7Bipolar Output 33A Hi Side/Lo Side DrivePWM7
B8Bipolar Output 43A Hi Side/Lo Side DrivePWM8
B9Low Side Output 123A Open CollectorUser Configurable Output
B10Low Side Output 133A Open CollectorGear Shift Air Pressure Relay
B11Cam Input 3VR/Hall - Software SelectableCam 3
B12Cam Input 4VR/Hall - Software SelectableCam 4
B13Ignition 5TTL/PowerShort circuit protection for Power
B14Ignition 6TTL/PowerShort circuit protection for Power
B15Ignition 7TTL/PowerGear Up Solenoid Output
B16Ignition 8TTL/PowerGear Down Solenoid Output
B17Hall Input 1Hall Effect InputWheel Speed LR
B18Hall Input 2Hall Effect InputWheel Speed RR
B19Hall Input 3Hall Effect InputWheel Speed LF
B20Hall Input 4Hall Effect InputWheel Speed RF
B21Knock 1 +
B22Knock 2 +
B23Knock GroundDigital Ground
B24Lambda 2 InputWeak bias to 450mVLambda 2
B25Analog Input 447k pull-up to VREFTPS2
B26Analog Input 547k pull-up to VREFPPS1
B27Analog Input 647k pull-up to VREFPPS2
B28NTC Input 43.16k pull-up to VREFGear Up Paddle Input
B29NTC Input 53.16k pull-up to VREFGear Down Paddle Input
B30Analog Input 747k pull-up to VREFOil Pressure Sensor Input
B31Analog Input 847k pull-up to VREFClutch Switch Input
B32Analog Input 947k pull-up to VREFNeutral Switch Input
B33Analog Input 1047k pull-up to VREFGear Shift Air Pressure Sensor
B34CAN 2L120 Ohm Terminated
B35CAN 2H

PC communications DB9 female

PinName
1Ground
6CAN High
7CAN Low
8Battery Voltage

PC communications DTM

PinName
1Battery Voltage
2Ground
3CAN High
4CAN Low

Calibration and installation

Record hardware identity, firmware and the existing calibration. The SXTune documentation covers crank and cam setup, sensor configuration, electronic throttle, output testing, data logging and CAN. Capabilities depend on the exact unit and firmware; the presence of a menu in shared software does not establish hardware support. Match sensors, coil and injector drivers and fuse values to the original model documentation before applying power.

See SCS Delta family guide, the manufacturer legacy upgrade notes and the wiring index.