Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Mitsubishi EVO 9 is a V Series plug-in ECU documented for Mitsubishi Lancer EVO 9. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tablesAll positions listed in the application-specific Vi-PEC installation guide, page 22, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. The guide repeats Aux–Ign 4 at pins 30 and 31 and Aux 3 at pins 41 and 63; verify the loom and configuration.Main ECU connector: documented positionsPositionECU function1Injection 156Aux – Inj 72Injection 457Aux – Inj 83Aux – Ign 561An Volt 24Aux – Ign 662An Temp 36Aux – Ign 763Aux 39Injection 266DI 211Ignition Cyls 1 and 467DI 712Ignition Cyls 2 and 368DI 514Aux 871An Volt 415Aux 578An Volt 318Aux 180DI 320Aux – Inj 583DI 421Aux – Ign 388DI 822Aux – Inj 690Aux – Ign 824Injection 391Knock 128Aux 792An Volt 147+14V Main Relay96An Temp 229Aux 699DI 630Aux – Ign 446Ground31Aux – Ign 432Aux 241Aux 343Trig 144An Temp 150Trig 253DI 154An Volt 555Aux 4Other connectionsPositionECU functionExpansion 1Signal GroundExpansion 2+5V OutExpansion 3DI 9Expansion 4DI 10Expansion 5An Volt 6Expansion 6An Volt 7Expansion 7An Volt 8Expansion 8An Temp 4
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Vi-PEC V Series Mitsubishi EVO 9
Vi-PEC V Series Mitsubishi EVO 9 is a V Series plug-in ECU documented for Mitsubishi Lancer EVO 9. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Revision 3: Vi-PEC V Series Mitsubishi EVO 9Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Mitsubishi EVO 9 is a V Series plug-in ECU documented for Mitsubishi Lancer EVO 9. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 22, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. The guide repeats Aux–Ign 4 at pins 30 and 31 and Aux 3 at pins 41 and 63; verify the loom and configuration.