Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Nissan S14-S15 GTIR is a V Series plug-in ECU documented for Nissan S14–S15 SR20 and GTI-R short-header applications listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tablesThese are the positions documented in the Vi-PEC Nissan SR short-header installation guide, pages 22–23, looking into the ECU from the wire side. Positions absent from the guide are not assumed unused. The manufacturer gives separate 1991–93 S13 and 1994–2002 S13 Type-X/S14/S15 schedules. It does not label a separate GTi-R pinout, so confirm GTi-R wiring with Vi-PEC. Verify the loom, engine and exact model before fitting. The later schedule lists Aux 1 at both pins 9 and 10.V1.2 lower-board issue: The guide identifies an incorrect tacho and ignition 1/2 connection when that board is used with 1991–93 SR20DET vehicles. It specifies jumper changes and a swap of header wires 2 and 3; consult its page 24 and the supplier before installation.1994–2002 S13 Type-X, S14 and S15PositionECU function101Injector 120An Volt 2102Aux 624Aux 4103Injector 325Ignition 4 / Aux – Ign 4104Aux 532DI 5105Aux – Inj 534DI 2106Aux – Inj 635DI 4110Injector 241DI 1111Aux 743DI 339Ground38+14V ECCS Relay112Injector 4113Aux – Inj 7114Aux 8115Aux – Inj 81Ignition 12Aux 23Ignition 2 / Aux – Ign 25Ignition 3 / Aux – Ign 39Aux 110Aux 111Aux 315An Temp 216An Volt 418An Temp 119An Volt 131, 40Trig 122, 30Trig 21991–1993 S13PositionECU function101Injector 120An Volt 2102Aux 624Aux 4103Injector 325Aux 1104Aux 532DI 5105Aux – Inj 534DI 2106Aux – Inj 635DI 4110Injector 241DI 1111Aux 743DI 339Ground38+14V ECCS Relay112Injector 4113Aux – Inj 7114Aux 8115Aux – Inj 81Aux 22Ignition 13Ignition 2 / Aux – Ign 28Ignition 3 / Aux – Ign 39Ignition 4 / Aux – Ign 411Aux 315An Temp 216An Volt 418An Temp 119An Volt 131, 40Trig 122, 30Trig 2Expansion connector and internal MAPPositionECU functionInternal MAPAn Volt 3Expansion 1Signal GroundExpansion 2+5V OutExpansion 3DI 6Expansion 4-Expansion 5An Volt 5Expansion 6An Volt 6Expansion 7An Temp 3Expansion 8-
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Vi-PEC V Series Nissan S14-S15 GTIR
Vi-PEC V Series Nissan S14-S15 GTIR is a V Series plug-in ECU documented for Nissan S14–S15 SR20 and GTI-R short-header applications listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Revision 4: Vi-PEC V Series Nissan S14-S15 GTIRVi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Nissan S14-S15 GTIR is a V Series plug-in ECU documented for Nissan S14–S15 SR20 and GTI-R short-header applications listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
These are the positions documented in the Vi-PEC Nissan SR short-header installation guide, pages 22–23, looking into the ECU from the wire side. Positions absent from the guide are not assumed unused. The manufacturer gives separate 1991–93 S13 and 1994–2002 S13 Type-X/S14/S15 schedules. It does not label a separate GTi-R pinout, so confirm GTi-R wiring with Vi-PEC. Verify the loom, engine and exact model before fitting. The later schedule lists Aux 1 at both pins 9 and 10.
V1.2 lower-board issue: The guide identifies an incorrect tacho and ignition 1/2 connection when that board is used with 1991–93 SR20DET vehicles. It specifies jumper changes and a swap of header wires 2 and 3; consult its page 24 and the supplier before installation.